Preparation of Cu2ZnSnS4 Thin Film by So-Gel Spin-Coated Deposition

2009 ◽  
Vol 79-82 ◽  
pp. 835-838 ◽  
Author(s):  
Min Yen Yeh ◽  
Chin Cheng Lee ◽  
Dong Sing Wuu
Keyword(s):  
Solar Cells ◽  
Energy Gap ◽  
Sol Gel ◽  
Solar Irradiation ◽  
Optical Absorption Coefficient ◽  
X Ray Diffraction ◽  
Optical Energy Gap ◽  
Texture Surface ◽  
X Ray ◽  
High Absorption

In this work Cu2ZnSnS4 (CZTS) suitable for the absorption layer in solar cells was successfully prepared by sol-gel spin-coated deposition. CZTS precursors were prepared by using solutions of copper (II) chloride, zinc (II) chloride, tin (IV) chloride, and thiourea. The CZTS with texture surface structures, resulting from 3 times of stacks through the cycles of spin-coated and synthesized (at 320 °C) processes, is found to be merged well together, and the thickness of the CZTS reaches ~ 3 μm. The kesterite crystallinity of the CZTS designated from the x-ray diffraction of (112), (200), (312), and (322) planes of CZTS were obtained. The optical-energy gap of the CZTS is about 1.5 eV. The average optical-absorption coefficient of the CZTS is ~ 2.4 x 104 cm-1, and the high absorption band of the CZTS covers most of the solar irradiation spectrum. This makes the CZTS the most potential material for solar cells. The chemical composition Cu:Zn:Sn:S = 30:14:16:40 of the CZTS is obtained at a synthesized temperature of 320 °C.

scholarly journals Laser induced plasma of cadmium oxide: structural, morphological and optical properties

2021 ◽  
Vol 2114 (1) ◽  
pp. 012012
Author(s):  
Tamara S. Hussein ◽  
Ala F. Ahmed
Keyword(s):  
Optical Properties ◽  
Energy Gap ◽  
Cadmium Oxide ◽  
X Ray Diffraction ◽  
Structural And Optical Properties ◽  
Optical Energy Gap ◽  
X Ray ◽  
Laser Induced Plasma ◽  
Atomic Force ◽  
Doping Ratio

Abstract In this study, the effect of grafting with Iron (Fe) ratios (0.1, 0.3 and 0.5) on the structural and optical properties of cadmium oxide films (CdO) was studied, as these films were prepared on glass bases using the method of pulse laser deposition (PLD). The crystallization nature of the prepared films was examined by X-ray diffraction technique (XRD), which showed that the synthesis of the prepared films is polycrystalline, and Atomic Force Microscope (AFM) images also showed that the increased vaccination with Iron led to an increase in the crustal size ratio and a decrease in surface roughness, The absorption coefficient was calculated and the optical energy gap for the prepared thin films. It was found the absorption decreases and the energy gap decreases with the increase of doping ratio.

An investigation of physical properties and photovoltaic performance of methylammonium lead-tin iodide (CH3NH3Sn1-xPbxI3) solar cells

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Omid Malekan ◽  
Mehdi Adelifard ◽  
Mohamad Mehdi Bagheri Mohagheghi
Keyword(s):  
Thin Films ◽  
Solar Cells ◽  
Conversion Efficiency ◽  
Photovoltaic Performance ◽  
Perovskite Solar Cells ◽  
X Ray Diffraction ◽  
Content Type ◽  
X Ray ◽  
High Absorption Coefficient ◽  
High Absorption

Purpose In the past several years, CH3NH3PbI3 perovskite material has been extensively evaluated as an absorber layer of perovskite solar cells due to its excellent structural and optical properties, and greater than 22% conversion efficiency. However, improvement and future commercialization of solar cells based on CH3NH3PbI3 encountered restrictions due to toxicity and instability of the lead element. Recently, studies on properties of lead-free and mixture of lead with other cations perovskite thin films as light absorber materials have been reported. The purpose of this paper was the fabrication of CH3NH3Sn1-xPbxI3 thin films with different SnI2 concentrations in ambient condition, and study on the structural, morphological, optical, and photovoltaic performance of the studied solar cells. The X-ray diffraction studies revealed the formation of both CH3NH3PbI3 and CH3NH3SnI3 phases with increasing the Sn concentration, and improvement in crystallinity and morphology was also observed. All perovskite layers had a relatively high absorption coefficient >104 cm−1 in the visible wavelengths, and the bandgap values varied in the range from 1.46 to 1.63 eV. Perovskite solar cells based on these thin films have been fabricated, and device performance was investigated. Results showed that photo-conversion efficiency (PCE) for the pure CH3NH3PbI3sample was 1.20%. With adding SnI2, PCE was increased to 4.48%. Design/methodology/approach In this work, the author mixed tin and lead with different percentages in the perovskite thin film. Also, the preparation of these layers and also other layers to fabricate solar cells based on them were conducted in an open and non-glove box environment. Finally, the effect of [Sn/Pb] ratio in the CH3NH3Sn1-xPbxI3 layers on the structural, morphological, optical, electrical and photovoltaic performance have been investigated. Findings CH3NH3Sn1-xPbxI3 (x = 0.0, 0.25, 0.50, 0.75, 1.0) perovskite thin films have been grown by a spin-coating technique. It was found that as tin concentration increases, the X-ray diffraction and FESEM images studies revealed the formation of both CH3NH3PbI3 and CH3NH3SnI3 phases, and improvement in crystallinity, and morphology; all thin films had high absorption coefficient values close to 104 cm−1 in the visible region, and the direct optical bandgap in the layers decreases from 1.63 eV in pure CH3NH3SnI3 to 1.46 eV for CH3NH3Sn0.0.25Pb0.75I3 samples; all thin films had p-type conductivity, and mobility and carrier density increased; perovskite solar cells based on these thin films have been fabricated, and device performance was investigated. Results showed that photo-conversion efficiency (PCE) for the pure CH3NH3PbI3sample was 1.20%. With adding SnI2, PCE was increased to 4.48%. Originality/value The preparation method seems to be interesting as it is in an ambient environment without the protection of nitrogen or argon gas.

Study of Heating Effect on Specific Surface Area, and Changing Optical Properties of ZnO Nanocrystals

2011 ◽  
Vol 403-408 ◽  
pp. 1205-1210
Author(s):  
Jaleh Babak ◽  
Ashrafi Ghazaleh ◽  
Gholami Nasim ◽  
Azizian Saeid ◽  
Golbedaghi Reza ◽  
...  
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Energy Gap ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
X Ray ◽  
Zno Nanocrystals ◽  
Transmission Electron ◽  
Zno Nanocrystal

In this work ZnO nanocrystal powders have been synthesized by using Zinc acetate dehydrate as a precursor and sol-gel method. Then the products have been annealed at temperature of 200-1050°C, for 2 hours. The powders were characterized using X-ray diffraction (XRD), UV-vis absorption and photoluminescence (PL) spectroscopy. The morphology of refrence ZnO nanoparticles have been studied using Transmission Electron Microscope (TEM). During the annealing process, increase in nanocrystal size, defects and energy gap quantitative, and decrease in specific surface area have been observed.

scholarly journals Optical and Structural investigations of LiNbO3 thin films by PLD

2020 ◽  
pp. 17-23
Keyword(s):  
Thin Film ◽  
Substrate Temperature ◽  
Energy Gap ◽  
Ultra Violet ◽  
Raw Material ◽  
Laser Deposition ◽  
X Ray Diffraction ◽  
Optical Energy Gap ◽  
Structural Investigations ◽  
X Ray

Lithium niobate (LiNbO3) nanostructure thin film was prepared and deposited on the substrates made of quartz by utilizing pulse laser deposition (PLD) technique. The effect of substrate temperature changing on the optical and structural properties of LiNbO3 films was investigated and studied. The chemical mixture was prepared by mixing the raw material (Li2CO3, Nb2O5) with Ethanol liquid without any further purification, at the stirrer time 3hrs without heating, then the formed material was overexposed to annealing process at 1000°C for 4hrs. LiNbO3 nanostructure thin film was characterized and analyzed by utilizing the Ultra-Violet visible (UV-vis) and X-Ray Diffraction (XRD). The UV-vis results showed that the increase in the substrate temperature to 300°C leads to decrease in the values of transmission (T%), absorption (A) and optical energy gap (Eg) and increase in the values of reflection (R%) and refractive index (n). While, the XRD results explained that the LiNbO3 structure became more pure and crystalline with increase the substrate temperature, because the intensity of the phase 2θ at the value of 34.8°, 40.06° and 48.48° correspond to (110), (113) and (024) planes disappeared at the substrate temperature 300°C. So, all presented results give a good indication to use LiNbO3 nanostructure thin film prepared at the substrate temperature 300°C for manufacturing the optical waveguide to give the best results.

scholarly journals Enhancement of vanadium oxide doped Eu+3 for gas sensor application

2019 ◽  
Vol 15 (33) ◽  
pp. 17-27
Author(s):  
Hassan M. Odhaib
Keyword(s):  
Thin Films ◽  
Response Time ◽  
Vanadium Oxide ◽  
Energy Gap ◽  
Average Frequency ◽  
Europium Oxide ◽  
X Ray Diffraction ◽  
Optical Energy Gap ◽  
X Ray ◽  
Vis Spectroscopy

Thin films of vanadium oxide nanoparticles doped with different concentrations of europium oxide (2, 4, 6, and 8) wt % are deposited on glass and Si substrates with orientation (111) utilizing by pulsed laser deposition technique using Nd:YAG laser that has a wavelength of 1064 nm, average frequency of 6 Hz and pulse duration of 10 ns. The films were annealed in air at 300 °C for two hours, then the structural, morphological and optical properties are characterized using x-ray diffraction (XRD), Field emission scanning electron microscopy (FESEM) and UV-Vis spectroscopy respectively. The X-ray diffraction results of V2O5:Eu2O3 exhibit that the film has apolycrystalline monoclinic V2O5 and triclinic V4O7 phases. The FESEM image shows a homogeneous pattern and confirms the formation of uniform nanostructures on the glass substrate. The type of the particle found nanoparticles with different doping concentrations of Eu2O3. The optical energy gap increases with the increase of doping concentration and it varies from 2.67 eV to 2.71 eV. The prepared thin films are used to fabricate sensor against nitrogen dioxide gas. The dependence of sensitivity and response time on doping ratio and operation temperature of gas sensors has been studied, the maximum sensitivity was about 100%, the response time is equal to 24s and recovery time 16s for V2O5 doped 2% Eu2O3 at 50 °C.

scholarly journals Structural, morphological and optical studies of sol-gel engineered Sm3+ activated ZnO thin films for photocatalytic applications

2020 ◽  
Vol 21 (3) ◽  
pp. 433-439
Author(s):  
T. Kiran ◽  
H. M. Parveez Ahmed ◽  
Noor Shahina Begum ◽  
Karthik Kannan ◽  
D. Radhika
Keyword(s):  
Thin Films ◽  
Energy Gap ◽  
Uv Light ◽  
Sol Gel ◽  
Average Crystallite Size ◽  
Hexagonal Wurtzite Structure ◽  
Zno Thin Films ◽  
X Ray Diffraction ◽  
Optical Energy Gap ◽  
Prepared Material

Rare earth (RE) ions activated ZnO thin films were prepared via sol-gel route and the thin films be categorized by various techniques. X-ray diffraction (XRD) studies display the hexagonal wurtzite structure of the prepared thin films. Scherrer's formula was utilized to calculate the average crystallite size (25–40 nm) with different Sm3+ concentrations. The optical energy gap was calculated by Diffused Reflectance spectra (DRS). The Acid Red (AR) dye was degraded under ultraviolet (UV) light irradiation with ZnO: Sm3+(1-9 mol %) nanostructured thin films  and the highest photodegradation (95 %) was observed for 7 mol %  of  Sm3+ doped ZnO catalyst. All the obtained results suggest that prepared material could be a prominent material as photocatalyst.

Synthesis, Characterization and Comparative Study of TiO2 and ZnO Nanoparticles and their Application as a Photocatalysts for a Trichromatic Dye

2020 ◽  
Vol 5 (3) ◽  
pp. 252-268
Author(s):  
Meriem Kouhail ◽  
El Ahmadi Zakia ◽  
Benayada Abbes
Keyword(s):  
Zno Nanoparticles ◽  
Diffuse Reflectance Spectroscopy ◽  
Dye Degradation ◽  
Sol Gel ◽  
Solar Irradiation ◽  
Operational Parameters ◽  
X Ray Diffraction ◽  
Aquatic Life ◽  
X Ray ◽  
Uv Visible

Background: The textile industrial effluents cause profound imbalances in ecosystems, when released into nature; dyes are oxidized by micro-organisms, resulting in a decrease in the dissolved oxygen, which is necessary for the aquatic life. For this reason, it is important to implement economic, efficient, and green methods ensuring both the discoloration and detoxification of water. Objective: TiO2 and ZnO nanoparticles were synthesized by sol-gel and precipitation methods, respectively. These two nanoparticles were used to compare photocatalytic degradation under UV and solar irradiation for three reactive azoic dyes (trichromatic): Reactive Bezactive Yellow (RBY), Reactive Bezactive Red (RBR), and Reactive Bezactive Blue (RBB). Methods: The structural, i.e., morphological surface properties of the synthesized photocatalysts were characterized by Fourier Transform Infrared, X-ray diffraction, UV-Visible diffuse reflectance spectroscopy, and Scanning Electron Microscopy. : X-ray diffraction shows that TiO2 has a tetragonal structure with an anatase form. The effects of some operational parameters, such as the amount of TiO2 and ZnO, initial dye concentration, dye mixtures, and pH, were examined. The progress of photodegradation reaction was monitored by UV-Visible spectroscopy for decolorization and by High-Performance Liquid Chromatography for degradation, and the efficiency of degradation was confirmed by Chemical Oxygen Demand measurement. Results: The dye degradation was found to be better in the presence of solar irradiation than under UV irradiation. The photocatalytic activity of ZnO was higher than TiO2 when used in its optimal conditions. Conclusion: The percentage of degradation of each dye is different, and the order of degradation of the three reactive dyes is as follows: RBY> RBR> RBB.

scholarly journals Synthesis and Characterization of 〖(CdO)〗_(1-x) 〖Mg〗_x films by pulsed laser deposition

2020 ◽  
Vol 18 (45) ◽  
pp. 59-67
Author(s):  
Jasim Mohamad Hussain ◽  
Awatif S Jasim ◽  
Kadhim Abdulwahid Aadim
Keyword(s):  
Absorption Coefficient ◽  
Energy Gap ◽  
Cadmium Oxide ◽  
Pulsed Laser ◽  
Laser Deposition ◽  
X Ray Diffraction ◽  
Structural And Optical Properties ◽  
Optical Energy Gap ◽  
X Ray

In this study, the effect of grafting with magnesium (Mg) ratios (0.1, 0.3, 0.5) on the structural and optical properties of cadmium oxide films (CdO) was studied, as these films were prepared on glass bases using the method of pulse laser deposition (PLD). The crystallization nature of the prepared membranes was examined by X-ray diffraction technique (XRD), which showed that the synthesis of the prepared membranes is polycrystalline, and (AFM) images also showed that the increased deformation with magnesium led to an increase in the grain size ratio and a decrease in surface roughness, as well as the absorption coefficient was calculated. And the optical energy gap for the prepared membranes, where it was found that the absorption coefficient increases with the increase in the proportion of vaccination and that the energy gap decreases with increasing rates of vaccination.

scholarly journals Structural and Optical Properties of ZnO-CdO Nanocomposite Using Electrodeposition Method

2016 ◽  
Vol 63 ◽  
pp. 127-133 ◽  
Author(s):  
Zehraa N. Abdul-Ameer ◽  
Ibrahim R. Agool
Keyword(s):  
Grain Size ◽  
Optical Properties ◽  
Surface Morphology ◽  
Electrochemical Deposition ◽  
Energy Gap ◽  
X Ray Diffraction ◽  
Structural And Optical Properties ◽  
Optical Energy Gap ◽  
X Ray ◽  
Shift Behavior

ZnO,CdO,ZnO-CdO nanocomposite were prepared using electrochemical deposition the prepared samples were characterized using X-ray diffraction and the photoluminenscence spectroscopy (PL) to get the surface morphology leading to calculation of optical energy gap .the grain size determined by Scherrer's equation (22-25) nm .through the calculation of Eg ,it was noticed a red shift behavior in ZnO manner due to addition of CdO content

scholarly journals Synthesized pure cobalt oxide nanostructure and doped with yttrium by hydrothermal method for photodetector applications

2019 ◽  
Vol 17 (40) ◽  
pp. 77-87
Author(s):  
Suhad A. Hamdan
Keyword(s):  
Optical Properties ◽  
Energy Gap ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
Optical Energy Gap ◽  
Nano Structure ◽  
X Ray ◽  
Pure Cobalt ◽  
Fast Rise ◽  
Higher Sensitivity

In this study, pure Co3O4 nano structure and doping with 4 %, and6 % of Yttrium is successfully synthesized by hydrothermal method.The XRD examination, optical, electrical and photo sensingproperties have been studied for pure and doped Co3O4 thin films.The X-ray diffraction (XRD) analysis shows that all films arepolycrystalline in nature, having cubic structure.The optical properties indication that the optical energy gap followsallowed direct electronic transition calculated using Tauc equationand it increases for doped Co3O4. The photo sensing properties ofthin films are studied as a function of time at different wavelengths tofind the sensitivity for these lights.High photo sensitivity doped Co3O4 with 6% of Yttrium, is a118.774% at wavelength 620 nm, while for pure Co3O4 films nosensitivity at the same wavelength. So, higher sensitivity is found fordoping Co3O4 with fast rise and fall times less than 1s.

Sign in / Sign up

Export Citation Format

Share Document