Effects of 0.03MF2 – 0.12LiF (M = Ca, Sr, Ba) on the Sintering and Dielectric Properties of SrTiO3 Ceramics

2013 ◽  
Vol 9 ◽  
pp. 1-12
Author(s):  
Laldja Taïbi-Benziada ◽  
Hassiba Kermoun ◽  
Yasmina Belaroussi
Keyword(s):  
Room Temperature ◽  
Single Phase ◽  
Sintering Temperature ◽  
Cubic Phase ◽  
Frequency Range ◽  
X Ray Diffraction ◽  
X Ray ◽  
Frequency Independent ◽  
Cold Pressed ◽  
Piezoelectric Devices

Cold-pressed pellets were prepared from the mixtures SrTiO3- 0.03MF2- 0.12LiF, M = Ca, Sr or Ba, then air-fired at 950 °C for 2 hours. The obtained samples were investigated by X-ray diffraction and scanning electron microscopy. Each ceramic is a perovskite single phase and the relative density reaches 95% for all ceramics. The addition of 3 mol. % of the eutectic composition 1MF2- 4LiF (Tm~ 760 °C) to SrTiO3lowers the sintering temperature of pure strontium titanate from 1400 °C to 950 °C and induces a strong modification in the SrTiO3cubic phase: superlattice reflections are detected and the unit cell symmetry becomes orthorhombic. Dielectric measurements were performed between - 150 °C and 200 °C in the frequency range 20 Hz - 109Hz. The dielectric permittivity εrshowed no maximum in the temperature range investigated and is almost frequency independent. At room temperature, the dielectric losses tanδ are less than 0.1 %. Moreover, the frequency dependence of the complex permittivity exhibits a resonance in the microwave region. These fluorinated ceramics could be of interest in piezoelectric devices and are promising dielectrics for class I capacitors manufactured at low temperature.

scholarly journals Transport and Dielectric Properties of Mechanosynthesized La2/3Cu3Ti4O12 Ceramics

Crystals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 313
Author(s):  
Mohamad M. Ahmad ◽  
Hicham Mahfoz Kotb ◽  
Celin Joseph ◽  
Shalendra Kumar ◽  
Adil Alshoaibi
Keyword(s):  
Dielectric Constant ◽  
Sintering Temperature ◽  
Cubic Phase ◽  
X Ray Diffraction ◽  
Boundary Conductivity ◽  
X Ray ◽  
Giant Dielectric ◽  
Mechanochemical Milling ◽  
Giant Dielectric Constant ◽  
Lower Temperature

La2/3Cu3Ti4O12 (LCTO) powder has been synthesized by the mechanochemical milling technique. The pelletized powder was conventionally sintered for 10 h at a temperature range of 975–1025 °C, which is a lower temperature process compared to the standard solid-state reaction. X-ray diffraction analysis revealed a cubic phase for the current LCTO ceramics. The grain size of the sintered ceramics was found to increase from 1.5 ± 0.5 to 2.3 ± 0.5 μm with an increase in sintering temperature from 975 to 1025 °C. The impedance results show that the grain conductivity is more than three orders of magnitude larger than the grain boundary conductivity for LCTO ceramics. All the samples showed a giant dielectric constant (1.7 × 103–3.4 × 103) and dielectric loss (0.09–0.17) at 300 K and 10 kHz. The giant dielectric constant of the current samples was attributed to the effect of internal barrier layer capacitances due to their electrically inhomogeneous structure.

Impedance Spectroscopy Study of LiTaO3 Powder Synthesized via Sol-Gel Method

2012 ◽  
Vol 545 ◽  
pp. 275-278 ◽  
Author(s):  
Lili Widarti Zainuddin ◽  
Norlida Kamarulzaman
Keyword(s):  
Room Temperature ◽  
Single Phase ◽  
Sol Gel ◽  
Rhombohedral Structure ◽  
Spectroscopy Study ◽  
X Ray Diffraction ◽  
Gel Method ◽  
X Ray ◽  
Sol Gel Method ◽  
Impedance Spectroscopy Study

A ceramics sample of LiTaO3 was prepared using a sol-gel method. The sample is annealed at 750 °C for 48 hours. X-ray diffraction analysis indicate the formation of single phase, rhombohedral structure. An ac impedance study was used to analyse the conductivity of LiTaO3 at room temperature and at various temperatures.

scholarly journals Equimolar Yttria-Stabilized Zirconia and Samaria-Doped Ceria Solid Solutions

Ceramics ◽  
2018 ◽  
Vol 1 (2) ◽  
pp. 343-352 ◽  
Author(s):  
Reginaldo Muccillo ◽  
Daniel de Florio ◽  
Eliana Muccillo
Keyword(s):  
Tetragonal Phase ◽  
Room Temperature ◽  
Single Phase ◽  
Rietveld Analysis ◽  
X Ray Diffraction ◽  
Ceramic Powders ◽  
Stabilized Zirconia ◽  
X Ray ◽  
Ceria Solid Solutions ◽  
Attrition Milling

Compositions of (ZrO2)0.92(Y2O3)0.08 (zirconia: 8 mol % yttria—8YSZ) and (CeO2)0.8(Sm2O3)0.2 (ceria: 20 mol % samaria—SDC20) ceramic powders were prepared by attrition milling to form an equimolar powder mixture, followed by uniaxial and isostatic pressing. The pellets were quenched to room temperature from 1200 °C, 1300 °C, 1400 °C and 1500 °C to freeze the defects configuration attained at those temperatures. X-ray diffraction analyses, performed in all quenched pellets, show the evolution of the two (8YSZ and SDC20) cubic fluorite structural phases to a single phase at 1500 °C, identified by Rietveld analysis as a tetragonal phase. Impedance spectroscopy analyses were carried out in pellets either quenched or slowly cooled from 1500 °C. Heating the quenched pellets to 1000 °C decreases the electrical resistivity while it increases in the slowly cooled pellets; the decrease is ascribed to annealing of defects created by lattice micro-tensions during quenching while the increase to partial destabilization of the tetragonal phase.

scholarly journals Sintering behaviour and microwave dielectric properties of MgO-2B2O3-xwt%BaCu(B2O5)-ywt%H3BO3 ceramics

2021 ◽  
Author(s):  
Haiquan Wang ◽  
Shixuan Li ◽  
Kangguo Wang ◽  
Xiuli Chen ◽  
Huanfu Zhou
Keyword(s):  
Dielectric Properties ◽  
Bulk Density ◽  
Single Phase ◽  
Sintering Temperature ◽  
Microwave Dielectric Properties ◽  
X Ray Diffraction ◽  
Microwave Dielectrics ◽  
X Ray ◽  
Microwave Dielectric ◽  
Sintering Behaviour

AbstractThis study investigates the bulk density, sintering behaviour, and microwave dielectric properties of the MgO-2B2O3 series ceramics synthesised by solid-state reaction. According to the X-ray diffraction and microstructural analyses, the as-prepared MgO-2B2O3 ceramics possess a single-phase structure with a rod-like morphology. The effects of different quantities of H3BO3 and BaCu(B2O5) (BCB) on the bulk density, sintering behaviour, and microwave dielectric properties of the MgO-2B2O3 ceramics were investigated. Accordingly, the optimal sintering temperature was obtained by adding 30 wt% H3BO3 and 8 wt% BCB. We also reduced the sintering temperature to 825 °C. Furthermore, the addition of 40 wt% H3BO3 and 4 wt% BCB increased the quality factor, permittivity, and temperature coefficient of resonance frequency of MgO-2B2O3 to 44,306 GHz (at 15 GHz), 5.1, and −32 ppm/°C, respectively. These properties make MgO-2B2O3 a viable low-temperature co-fired ceramic with broad applications in microwave dielectrics.

scholarly journals Structure and electric properties of cerium substituted SrBi1.8Ce0.2Nb2O9 and SrBi1.8Ce0.2Ta2O9 ceramics

2016 ◽  
Vol 10 (3) ◽  
pp. 183-188 ◽  
Author(s):  
Mohamed Afqir ◽  
Amina Tachafine ◽  
Didier Fasquelle ◽  
Mohamed Elaatmani ◽  
Jean-Claude Carru ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Solid State ◽  
Room Temperature ◽  
Single Phase ◽  
Solid State Reaction Method ◽  
X Ray Diffraction ◽  
Reaction Method ◽  
X Ray ◽  
Lcr Meter ◽  
Curie Temperature Tc

SrBi1.8Ce0.2Nb2O9 (SBCN) and SrBi1.8Ce0.2Ta2O9 (SBCT) powders were prepared via solid-state reaction method. X-ray diffraction analysis reveals that the SBCN and SBCT powders have the single phase orthorhom-bic Aurivillius structure at room temperature. The contribution of Raman scattering and FTIR spectroscopy of these samples were relatively smooth and resemble each other. The calcined powders were uniaxially pressed and sintered at 1250?C for 8 h to obtaine dense ceramics. Dielectric constant, loss tangent and AC conductivity of the sintered Ce-doped SrBi2Nb2O9 and SrBi2Ta2O9 ceramics were measured by LCR meter. The Ce-doped SBN (SBCN) ceramics have a higher Curie temperature (TC) and dielectric constant at TC (380?C and ?? ~3510) compared to the Ce-doped SBT (SBCT) ceramics (330?C and ?? ~115) when measured at 100Hz. However, the Ce-doped SBT (SBCT) ceramics have lower conductivity and dielectric loss.

scholarly journals Ferromagnetic Order in the Intermetallic Alloys laNi5-xMgx

2012 ◽  
Vol 29 (1) ◽  
pp. 50
Author(s):  
D.N Ba ◽  
L.T Tai ◽  
N.T Trung ◽  
N.T Huy
Keyword(s):  
Magnetic Properties ◽  
Curie Temperature ◽  
Room Temperature ◽  
Single Phase ◽  
Chemical Doping ◽  
Intermetallic Alloys ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ferromagnetic Order ◽  
Diffraction Patterns

The influences of the substitution of Ni with Mg on crystallographic and magnetic properties of the intermetallic alloys LaNi5-xMgx (x ≤ 0.4) were investigated. The X-ray diffraction patterns showed that all samples were of single phase, and the lattice parameters, a and c, decreased slightly upon chemical doping. LaNi5 is well known as an exchange-enhanced Pauli paramagnet. Interestingly, in LaNi5-xMgx, the ferromagnetic order existed even with a small amount of dopants; the Curie temperature reached the value of room temperature for x = 0.2, and enhanced with increasing x.

Synthesis and Luminescence Properties of Chalcopyrite-Type CuAlS2

2006 ◽  
Vol 301 ◽  
pp. 177-180 ◽  
Author(s):  
Yuichiro Kuroki ◽  
Tomoichiro Okamoto ◽  
Masasuke Takata
Keyword(s):  
Diffraction Analysis ◽  
Room Temperature ◽  
Single Phase ◽  
Elevated Temperatures ◽  
Emission Peak ◽  
Maximum Intensity ◽  
X Ray Diffraction ◽  
Ultraviolet Emission ◽  
X Ray ◽  
Copper Aluminum

Copper aluminum disulfide (CuAlS2) powders were synthesized in an evacuated ampoule at elevated temperatures. X-ray diffraction analysis revealed that the powders heated at temperatures higher than 800oC were single-phase CuAlS2. In the cathodoluminescence (CL) spectra measured at room temperature, the powders heated at temperatures higher than 600oC exhibited a visible emission peak at approximately 1.8 eV and a distinct ultraviolet emission peak at 3.45 eV. The powder heated at 700oC showed the maximum intensity of ultraviolet emission which is considered to be associated with excitons.

X-ray diffraction study of oxygen-conducting compoundsLn2Mo2O9(Ln= La, Pr)

2014 ◽  
Vol 70 (4) ◽  
pp. 669-675 ◽  
Author(s):  
Alexander M. Antipin ◽  
Olga A. Alekseeva ◽  
Natalia I. Sorokina ◽  
Alexandra N. Kuskova ◽  
Michail Yu. Presniakov ◽  
...  
Keyword(s):  
Room Temperature ◽  
Cubic Phase ◽  
X Ray Diffraction ◽  
Ion Migration ◽  
Transmission Microscopy ◽  
Coordination Environment ◽  
X Ray ◽  
Oxygen Ions ◽  
Oxygen Ion ◽  
Oxygen Ion Migration

The La2Mo2O9(LM) and Pr2Mo2O9(PM) single crystals are studied using precision X-ray diffraction and high-resolution transmission microscopy at room temperature. The crystal structures are determined in the space groupP213. La and Pr atoms, as well as Mo1 and O1 atoms, are located in the vicinity of the threefold axes rather than on the axes as in the high-temperature cubic phase. In both structures studied, the O2 and O3 positions are partially occupied. The coexistence of different configurations of the Mo coordination environment facilitates the oxygen-ion migration in the structure. Based on the X-ray data, the activation energies of O atoms are calculated and the migration paths of oxygen ions in the structures are analysed. The conductivity of PM crystals is close to that of LM crystals. The O2 and O3 atoms are the main contributors to the ion conductivity of LM and PM.

scholarly journals Cubic InGaN Grown by MOCVD

1999 ◽  
Vol 4 (S1) ◽  
pp. 239-243
Author(s):  
J.B. Li ◽  
Hui Yang ◽  
L.X. Zheng ◽  
D.P. Xu ◽  
Y.T. Wang
Keyword(s):  
Room Temperature ◽  
Emission Peak ◽  
Buffer Layers ◽  
Cubic Phase ◽  
Yellow Luminescence ◽  
X Ray Diffraction ◽  
High Quality ◽  
X Ray ◽  
Cubic Gan ◽  
Pl Emission

We report on the growth of high-quality cubic phase InGaN on GaAs by MOCVD. The cubic InGaN layers are grown on cubic GaN buffer layers on GaAs (001) substrates. The surface morphology of the films are mirror-like. The cubic nature of the InGaN films is obtained by X-ray diffraction (XRD) measurements. The InGaN layers show strong photoluminescence (PL) at room temperature. Neither emission peak from wurtzite GaN nor yellow luminescence is observed in our films. The highest In content as determined by XRD is about 17% with an PL emission wavelength of 450 nm. The FWHM of the cubic InGaN PL peak are 153 meV and 216 meV for 427 nm and 450 nm emissions, respectively. It is found that the In compositions determined from XRD are not in agreement with those estimated from PL measurements. The reasons for this disagreement are discussed.

PHASE STRUCTURE, PIEZOELECTRIC AND MULTIFERRIOC BEHAVIOR OF (K0.48Na0.52)NbO3-Co2O3 PIEZOELECTRIC CERAMICS

2011 ◽  
Vol 04 (03) ◽  
pp. 225-229 ◽  
Author(s):  
WENJUAN WU ◽  
DINGQUAN XIAO ◽  
JIAGANG WU ◽  
JING LI ◽  
JIANGUO ZHU
Keyword(s):  
Room Temperature ◽  
Sintering Temperature ◽  
Magnetic Behavior ◽  
Orthorhombic Phase ◽  
Piezoelectric Ceramics ◽  
X Ray Diffraction ◽  
Two Phase ◽  
X Ray ◽  
Solid State Sintering ◽  
Sintering Method

( K 0.48 Na 0.52) NbO 3-x% Co 2 O 3 (x = 0, 0.03 and 0.05) (KNN-x% Co2O3 ) lead-free piezoelectric ceramics were prepared by the conventional solid-state sintering method. An orthorhombic phase was observed for all KNN-x% Co2O3 ceramics at room temperature, and two phase transitions were confirmed by the high temperature X-ray diffraction and the temperature dependence of the dielectric constant. The Co2O3 greatly improves the density and decreases the sintering temperature of KNN ceramics. The KNN-0.05 mol%Co2O3 ceramic exhibits good properties (d33 = 120 pC/N , k p = 0.41, Q m = 213 and T c = 407°C) and a good age stability. The multiferroic behavior was also observed at room temperature for the KNN-0.05 mol%Co2O3 ceramic, as confirmed by P–E loops and magnetic behavior.

Sign in / Sign up

Export Citation Format

Share Document