Fracture Properties and Characteristics of Sisal Textile Reinforced Epoxy Composites

2006 ◽  
Vol 312 ◽  
pp. 167-172
Author(s):  
Yan Li ◽  
Yiu Wing Mai ◽  
Lin Ye
Keyword(s):  
Fracture Toughness ◽  
Surface Treatment ◽  
Fiber Surface ◽  
Epoxy Composites ◽  
Mode I ◽  
Mode Ii ◽  
Fracture Properties ◽  
Pull Out ◽  
Mode Ii Fracture Toughness ◽  
Fiber Surface Treatment

In this paper, double cantilever beam (DCB) and end notch flexural (ENF) tests were performed to study mode I and mode II interlaminar fracture toughness of sisal textile reinforced epoxy composites. Two kinds of fiber surface treatment methods were used to improve the interfacial bonding properties between sisal fiber and the epoxy resin. Effect of fiber surface treatments on mode I and mode II fracture toughness was analyzed with the aid of microobservation and single fiber pull-out test. It was concluded that proper fiber surface treatment could improve the fracture properties of this kind of Eco-composite.

scholarly journals Displacement Rate Effects on the Mode II Shear Delamination Behavior of Carbon Fiber/Epoxy Composites

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1881
Author(s):  
Kean Ong Low ◽  
Mahzan Johar ◽  
Haris Ahmad Israr ◽  
Khong Wui Gan ◽  
Seyed Saeid Rahimian Koloor ◽  
...  
Keyword(s):  
Fracture Toughness ◽  
Peak Load ◽  
Epoxy Composites ◽  
Displacement Rate ◽  
Interface Debonding ◽  
Mode Ii ◽  
Scanning Electron Micrographs ◽  
Unstable Crack ◽  
Mode Ii Fracture ◽  
Mode Ii Fracture Toughness

This paper studies the influence of displacement rate on mode II delamination of unidirectional carbon/epoxy composites. End-notched flexure test is performed at displacement rates of 1, 10, 100 and 500 mm/min. Experimental results reveal that the mode II fracture toughness GIIC increases with the displacement, with a maximum increment of 45% at 100 mm/min. In addition, scanning electron micrographs depict that fiber/matrix interface debonding is the major damage mechanism at 1 mm/min. At higher speeds, significant matrix-dominated shear cusps are observed contributing to higher GIIC. Besides, it is demonstrated that the proposed rate-dependent model is able to fit the experimental data from the current study and the open literature generally well. The mode II fracture toughness measured from the experiment or deduced from the proposed model can be used in the cohesive element model to predict failure. Good agreement is found between the experimental and numerical results, with a maximum difference of 10%. The numerical analyses indicate crack jump occurs suddenly after the peak load is attained, which leads to the unstable crack propagation seen in the experiment.

scholarly journals Mixed-Mode Interlaminar Fracture Toughness of Glass and Carbon Fibre Powder Epoxy Composites—For Design of Wind and Tidal Turbine Blades

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2103
Author(s):  
Christophe Floreani ◽  
Colin Robert ◽  
Parvez Alam ◽  
Peter Davies ◽  
Conchúr M. Ó. Brádaigh
Keyword(s):  
Fracture Toughness ◽  
Carbon Fibre ◽  
Composite Structures ◽  
Mixed Mode ◽  
Epoxy Composites ◽  
Mode I ◽  
Mode Ii ◽  
Pure Mode ◽  
Interlaminar Fracture Toughness ◽  
Interlaminar Fracture

Powder epoxy composites have several advantages for the processing of large composite structures, including low exotherm, viscosity and material cost, as well as the ability to carry out separate melting and curing operations. This work studies the mode I and mixed-mode toughness, as well as the in-plane mechanical properties of unidirectional stitched glass and carbon fibre reinforced powder epoxy composites. The interlaminar fracture toughness is studied in pure mode I by performing Double Cantilever Beam tests and at 25% mode II, 50% mode II and 75% mode II by performing Mixed Mode Bending testing according to the ASTM D5528-13 test standard. The tensile and compressive properties are comparable to that of standard epoxy composites but both the mode I and mixed-mode toughness are shown to be significantly higher than that of other epoxy composites, even when comparing to toughened epoxies. The mixed-mode critical strain energy release rate as a function of the delamination mode ratio is also provided. This paper highlights the potential for powder epoxy composites in the manufacturing of structures where there is a risk of delamination.

scholarly journals Effect of sewage sludge ash filler on mode I and mode II interlaminar fracture toughness of S-glass/epoxy composites

2018 ◽  
Vol 1 (2) ◽  
Author(s):  
Mohamad Alsaadi 1,2 ◽  
Ahmet Erkliğ 2
Keyword(s):  
Fracture Toughness ◽  
Sewage Sludge ◽  
Epoxy Composites ◽  
Mode I ◽  
Mode Ii ◽  
Interlaminar Fracture Toughness ◽  
Sewage Sludge Ash ◽  
Interlaminar Fracture ◽  
Glass Fiber Reinforced ◽  
Sludge Ash

In this study, the influence of sewage sludge ash (SSA) waste particle contents on the mechanical properties and interlaminar fracture toughness for mode I and mode II delamination of S-glass fiber reinforced epoxy composites were investigated. Composite laminate specimens for tensile, flexural double-cantilever beam (DCB) and end-notched flexure (ENF) tests were prepared and tested according to ASTM standards with 5, 10, 15 and 20 wt% SSA filled S-glass/epoxy composites. Properties improvement reasons was explained based on optical and scanning electron microscopy. The highest improvement in tensile and flexural strength was obtained with 10 wt% content of SSA. The highest mode I and mode II interlaminar fracture toughness’s were obtained with 15 wt% content of SSA. The mode I and mode II interlaminar fracture toughness’s improved by 33 and 63.6%, respectively, compared to the composite without SSA.

Sign in / Sign up

Export Citation Format

Share Document