Vibration Characteristic of Violin Bowstring and Experimental Research on Helmholtz Motion of String

2014 ◽  
Vol 621 ◽  
pp. 707-711
Author(s):  
Bang Yan Ye ◽  
Jian Ping Liu ◽  
Cheng Zhong Zhang ◽  
X.Z. Zhao ◽  
S.S. Liang ◽  
...  
Keyword(s):  
High Speed ◽  
Interaction Mechanism ◽  
Process Time ◽  
High Speed Photography ◽  
Vibration Characteristic ◽  
Vibration System ◽  
Vibration Displacement ◽  
Stick Slip ◽  
String Vibration ◽  
Sawtooth Waveform

The sound source of violin is string vibration. By the stick–slip friction action between bow and string of violin, string and bridge form a complicated vibration system. The interaction mechanism of bowstring is very intricacy. In this paper, through theoretical analysis and experiment, the vibration behavior of violin string is investigated. We measured the vibration images of bowing and plucking violin string on a high-speed photography optical platform and got two different character of string vibration, including vibration displacement, velocity and space trajectory of the mark point on string. By comparing the displacement curves of the different points among on string, the variety of the ratio of positive process time to negative one of vibration sawtooth waveform are studied, and also the formation process of string vibration enveloping curve. On this basis, the Helmholtz motion of string vibration which is presented at 1862 is studied.

Crack divergence phenomena in tempered glass

2020 ◽  
Vol 13 (3) ◽  
pp. 115-129
Author(s):  
Shin’ichi Aratani
Keyword(s):  
Optimal Design ◽  
High Speed ◽  
Glass Plate ◽  
Acute Angle ◽  
Divergence Angle ◽  
High Speed Photography ◽  
Tempered Glass ◽  
Thick Glass

High speed photography using the Cranz-Schardin camera was performed to study the crack divergence and divergence angle in thermally tempered glass. A tempered 3.5 mm thick glass plate was used as a specimen. It was shown that two types of bifurcation and branching existed as the crack divergence. The divergence angle was smaller than the value calculated from the principle of optimal design and showed an acute angle.

Experimental study of hydrodynamic effects in the inverse water hydrocarbon emulsions flow in microchannels

2016 ◽  
Vol 11 (1) ◽  
pp. 30-37 ◽  
Author(s):  
A.A. Rakhimov ◽  
A.T. Akhmetov
Keyword(s):  
High Speed ◽  
Petroleum Industry ◽  
Chemical Compounds ◽  
High Viscosity ◽  
Blocking Effect ◽  
High Speed Photography ◽  
Simple Chemical ◽  
Reported Study ◽  
Dynamic Blocking ◽  
Hydrodynamic Effects

The paper presents results of hydrodynamic and rheological studies of the inverse water hydrocarbon emulsions. The success of the application of invert emulsions in the petroleum industry due, along with the high viscosity of the emulsion, greatly exceeding the viscosity of the carrier phase, the dynamic blocking effect, which consists in the fact that the rate of flow of emulsions in capillary structures and cracks falls with time to 3-4 orders, despite the permanent pressure drop. The reported study shows an increase in viscosity with increasing concentration or dispersion of emulsion. The increase in dispersion of w/o emulsion leads to an acceleration of the onset of dynamic blocking. The use of microfluidic devices, is made by soft photolithography, along with high-speed photography (10,000 frames/s), allowed us to see in the blocking condition the deformation of the microdroplets of water in inverse emulsion prepared from simple chemical compounds.

scholarly journals Prey Capturing Dynamics and Nanomechanically Graded Cutting Apparatus of Dragonfly Nymph

Materials ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 559
Author(s):  
Lakshminath Kundanati ◽  
Prashant Das ◽  
Nicola M. Pugno
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
High Speed ◽  
Prey Capture ◽  
High Speed Photography ◽  
Sensory Organs ◽  
Dragonfly Nymph ◽  
Drag Forces ◽  
Predatory Insects ◽  
Dragonfly Nymphs

Aquatic predatory insects, like the nymphs of a dragonfly, use rapid movements to catch their prey and it presents challenges in terms of movements due to drag forces. Dragonfly nymphs are known to be voracious predators with structures and movements that are yet to be fully understood. Thus, we examine two main mouthparts of the dragonfly nymph (Libellulidae: Insecta: Odonata) that are used in prey capturing and cutting the prey. To observe and analyze the preying mechanism under water, we used high-speed photography and, electron microscopy. The morphological details suggest that the prey-capturing labium is a complex grasping mechanism with additional sensory organs that serve some functionality. The time taken for the protraction and retraction of labium during prey capture was estimated to be 187 ± 54 ms, suggesting that these nymphs have a rapid prey mechanism. The Young’s modulus and hardness of the mandibles were estimated to be 9.1 ± 1.9 GPa and 0.85 ± 0.13 GPa, respectively. Such mechanical properties of the mandibles make them hard tools that can cut into the exoskeleton of the prey and also resistant to wear. Thus, studying such mechanisms with their sensory capabilities provides a unique opportunity to design and develop bioinspired underwater deployable mechanisms.

Droplet transfer behavior of narrow gap laser wire filling welding

2019 ◽  
Vol 33 (01n03) ◽  
pp. 1940045 ◽  
Author(s):  
Z. Zhang ◽  
R. Wang ◽  
G. Gou ◽  
H. Chen ◽  
W. Gao
Keyword(s):  
Welding Speed ◽  
High Speed ◽  
Transition Period ◽  
High Speed Photography ◽  
Narrow Gap ◽  
Droplet Transfer ◽  
Transfer Behavior ◽  
Feeding Speed ◽  
Wire Feeding ◽  
Droplet Transition

In this paper, we study the droplet transition behavior of narrow gap laser wire filling welding under the condition of changing welding speed and wire feeding speed, and it was observed by high-speed photography. It was found that with the increase of welding speed, the frequency of droplet transfer was reduced and the transition period was prolonged. With the increase of wire feeding speed, the wire was not fully melted and finally inserted into the molten pool.

Experimental Characterization of a Modified Airlift Pump

2014 ◽  
Author(s):  
Afshin Goharzadeh ◽  
Keegan Fernandes
Keyword(s):  
Water Flow ◽  
Flow Rate ◽  
High Speed ◽  
Water Flow Rate ◽  
High Speed Photography ◽  
Two Phase ◽  
Inner Diameter ◽  
Airlift Pump ◽  
Flow Map ◽  
Churn Flow

This paper presents an experimental investigation on a modified airlift pump. Experiments were undertaken as a function of air-water flow rate for two submergence ratios (ε=0.58 and 0.74), and two different riser geometries (i) straight pipe with a constant inner diameter of 19 mm and (ii) enlarged pipe with a sudden expanded diameter of 19 to 32 mm. These transparent vertical pipes, of 1 m length, were submerged in a transparent rectangular tank (0.45×0.45×1.1 m3). The compressed air was injected into the vertical pipe to lift the water from the reservoir. The flow map regime is established for both configurations and compared with previous studies. The two phase air-water flow structure at the expansion region is experimentally characterized. Pipeline geometry is found to have a significant influence on the output water flow rate. Using high speed photography and electrical conductivity probes, new flow regimes, such as “slug to churn” and “annular to churn” flow, are observed and their influence on the output water flow rate and efficiency are discussed. These experimental results provide fundamental insights into the physics of modified airlift pump.

A study of the collapse of arrays of cavities

1988 ◽  
Vol 190 ◽  
pp. 409-425 ◽  
Author(s):  
J. P. Dear ◽  
J. E. Field
Keyword(s):  
Shock Wave ◽  
High Speed ◽  
High Speed Photography ◽  
Cavitation Damage ◽  
Major Mechanism ◽  
Collapse Mechanisms ◽  
Multiple Jets ◽  
Circular Holes ◽  
Schlieren Photography ◽  
Thick Glass

This paper describes a method for examining the collapse of arrays of cavities using high-speed photography and the results show a variety of different collapse mechanisms. A two-dimensional impact geometry is used to enable processes occurring inside the cavities such as jet motion, as well as the movement of the liquid around the cavities, to be observed. The cavity arrangements are produced by first casting water/gelatine sheets and then forming circular holes, or other desired shapes, in the gelatine layer. The gelatine layer is placed between two thick glass blocks and the array of cavities is then collapsed by a shock wave, visualized using schlieren photography and produced from an impacting projectile. A major advantage of the technique is that cavity size, shape, spacing and number can be accurately controlled. Furthermore, the shape of the shock wave and also its orientation relative to the cavities can be varied. The results are compared with proposed interaction mechanisms for the collapse of pairs of cavities, rows of cavities and clusters of cavities. Shocks of kbar (0.1 GPa) strength produced jets of c. 400 m s−1 velocity in millimetre-sized cavities. In closely-spaced cavities multiple jets were observed. With cavity clusters, the collapse proceeded step by step with pressure waves from one collapsed row then collapsing the next row of cavities. With some geometries this leads to pressure amplification. Jet production by the shock collapse of cavities is suggested as a major mechanism for cavitation damage.

Sign in / Sign up

Export Citation Format

Share Document