droplet transfer
Recently Published Documents


TOTAL DOCUMENTS

172
(FIVE YEARS 68)

H-INDEX

15
(FIVE YEARS 4)

2022 ◽  
Vol 148 ◽  
pp. 107781
Author(s):  
Wei Sun ◽  
Shushuai Liu ◽  
Fuqiang Guo ◽  
Dongting Wu ◽  
Yongang Zhang ◽  
...  

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Saeed Behzadinasab ◽  
Alex W. H. Chin ◽  
Mohsen Hosseini ◽  
Leo L. M. Poon ◽  
William A. Ducker

AbstractTransfer of SARS-CoV-2 from solids to fingers is one step in infection via contaminated solids, and the possibility of infection from this route has driven calls for increased frequency of handwashing during the COVID-19 pandemic. To analyze this route of infection, we measured the percentage of SARS-CoV-2 that was transferred from a solid to an artificial finger. A droplet of SARS-CoV-2 suspension (1 µL) was placed on a solid, and then artificial skin was briefly pressed against the solid with a light force (3 N). Transfer from a variety of solids was detected, and transfer from the non-porous solids, glass, stainless steel, and Teflon, was substantial when the droplet was still wet. The viral titer for the finger was 13–16% or 0.8–0.9 log less than for the input droplet. Transfer still occurred after the droplet evaporated, but was smaller, 3–9%. We found a lower level of transfer from porous solids but did not find a significant effect of solid wettability for non-porous solids.


Metals ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 1712
Author(s):  
Baihao Cai ◽  
Juan Fu ◽  
Yong Zhao ◽  
Fugang Chen ◽  
Yonghui Qin ◽  
...  

In this paper, the morphological characteristics of arc plasma and droplet transfer during the alternating magnetic field-assisted narrow gap groove laser-MIG (metal inert gas) hybrid welding process were investigated. The characteristics of arc plasma and droplet transfer, electron temperature, and density were analyzed using a high-speed camera and spectrum diagnosis. Our results revealed that the arc maintained a relatively stable state and rotated at a high speed to enhance the arc stiffness, and further improved the stability of the arc under the alternating magnetic field. The optimum magnetic field parameters in this experiment were B = 16 mT and f = 20 Hz, the electron temperature was 9893.6 K and the electron density was 0.99 × 1017 cm−3 near the bottom of the groove, which improved the temperature distribution inside the narrow gap groove and eliminated the lack of sidewall fusion defect. Compared to those without a magnetic field, the magnetic field could promote droplet transfer, the droplet diameter decreased by 17.6%, and the transition frequency increased by 23.5% (owing to the centrifugal force during droplet spinning and electromagnetic contraction force). The width of the weld bead was increased by 12.4% and the pores were also significantly reduced due to the stirring of the magnetic field on the molten pool.


Metals ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 1510
Author(s):  
Leilei Wang ◽  
Yanqiu Zhao ◽  
Yue Li ◽  
Xiaohong Zhan

Hybrid laser arc welding (HLAW) features advantages such as higher welding speed and gap tolerance as well as smaller welding deformation and heat-affected zone than arc welding. Porosity in hybrid laser arc weld due to keyhole fluctuation tends to be the initial source of crack propagation, which will significantly diminish the weld performance. A high-speed imaging technique was adopted to record and analyze the droplet transfer and keyhole fluctuation behavior during hybrid laser arc welding of aluminum alloys. A heat transfer and fluid flow model of HLAW was established and validated for a perspective of the evolution process of droplet transfer and keyhole fluctuation. The relationship between keyhole fluctuation and weld porosity was also revealed. During the droplet transfer stage, liquid metal on the top surface of the weld pool flows toward the keyhole originated by globular transfer, and the keyhole fluctuates and decreases significantly, which has a higher tendency to form a bubble in the weld pool. The bubble evolves into porosity once trapped in the mush-zone near the trailing edge of the weld pool. Therefore, globular transfer during HLAW is the principal origin of keyhole fluctuation and weld porosity. Welding current has a significant influence on keyhole fluctuation and weld porosity rate. Droplet transfer frequency, keyhole fluctuation, and porosity rate increase with higher welding current under the globular transfer mode. The porosity rate shows a nearly positive correlation with the standard deviation of keyhole fluctuation.


Sign in / Sign up

Export Citation Format

Share Document