Characteristics of Ni-Zn Rechargeable Batteries with Zn Anode Prepared by Using Nano-Cellulose as its Binder Agent

2021 ◽  
Vol 1028 ◽  
pp. 105-110
Author(s):  
Rida Nurul Shelni Rofika ◽  
Mardiyati Mardiyati ◽  
Rahmat Hidayat
Keyword(s):  
Zno Nanoparticles ◽  
Large Scale ◽  
Low Cost ◽  
Rechargeable Batteries ◽  
Li Ion Batteries ◽  
Host Matrix ◽  
Nano Cellulose ◽  
Li Ion ◽  
Zn Anode ◽  
Scale Usage

While the operating voltages of Ni-Zn batteries are smaller than Li-ion batteries, Ni-Zn batteries offer some advantages, such as high specific energy and low cost. Ni-Zn batteries use green materials as they use aqueous electrolytes and do not need hazardous organic solvents. Both Ni and Zn are abundant and much less expensive in comparison to lithium. Therefore, Ni-Zn batteries are more suitable as secondary batteries for applications that do not need mobility, such as for storing electricity from solar panels at home or office building. At present, large scale usage of Ni-Zn batteries is hindered by their low life cycle due to Zn anode degradation during the operation. The Zn anode deteriorates as dendrite and passivation growth causing self-discharge at the Zn anode. Many efforts have been tried to solve those problems by adding additives in the electrode or electrolyte and a specific binder in the Zn anode. In the present work, in addition to standard CMC and PTFE as the binder in Zn anode, we also added nano-cellulose as its binder agent as the host matrix may be formed with a much smaller void, providing much more dispersion of ZnO nanoparticles and better reduction on Zn dendrite formation. The battery structures in this work were Zn-anode | electrolytes (KOH, aqueous) | Ni-cathode. Ni cathode used in this work is similar to those found in commercial Ni-Zn batteries. The Zn anode was prepared with various compositions of binder and hydroxides, such as Ca(OH)2, and ZnO nanoparticles as the active materials. The characteristics of the batteries are largely affected by the composition of the binder and other substances forming the Zn anode, particularly the proportion of the hydroxide. However, in general, the present result shows the potential of this modified Ni-Zn battery as an alternative to supersede expensive Li-ion batteries for low-cost and stationary applications.

Green water-based binders for LiFePO4/C cathode in Li-ion batteries: a comparative study

2021 ◽  
Author(s):  
Xiaojing Zhang ◽  
xinyi Ge ◽  
Zhigang Shen ◽  
Han Ma ◽  
Jingshi Wang ◽  
...  
Keyword(s):  
Comparative Study ◽  
Polyvinylidene Fluoride ◽  
Low Cost ◽  
Green Water ◽  
Li Ion Batteries ◽  
Environmental Friendliness ◽  
Water Based ◽  
Li Ion

Compared with environmentally harmful binder polyvinylidene fluoride (PVDF) in Li-ion batteries (LIBs), water-based binders have many advantages, such as low cost, rich sources and environmental friendliness. In this study, various...

Novel low-cost, high-energy-density (>700 Wh kg−1) Li-rich organic cathodes for Li-ion batteries

2021 ◽  
Vol 415 ◽  
pp. 128509
Author(s):  
Qihang Yu ◽  
Wu Tang ◽  
Yang Hu ◽  
Jian Gao ◽  
Ming Wang ◽  
...  
Keyword(s):  
Energy Density ◽  
Low Cost ◽  
High Energy ◽  
High Energy Density ◽  
Li Ion Batteries ◽  
Li Ion

Organic electrode materials for non-aqueous, aqueous, and all-solid-state Na-ion batteries

2021 ◽  
Author(s):  
Kathryn Holguin ◽  
Motahareh Mohammadiroudbari ◽  
Kaiqiang Qin ◽  
Chao Luo
Keyword(s):  
Solid State ◽  
High Performance ◽  
Electrode Materials ◽  
Low Cost ◽  
Li Ion Batteries ◽  
Organic Electrode ◽  
Li Ion

Na-ion batteries (NIBs) are promising alternatives to Li-ion batteries (LIBs) due to the low cost, abundance, and high sustainability of sodium resources. However, the high performance of inorganic electrode materials...

Recovery Value Metals from Mixed Spent Li-Ion Batteries

2014 ◽  
Vol 540 ◽  
pp. 267-271
Author(s):  
Xin Liu ◽  
Lin Yan Li ◽  
Fan Yun Zeng ◽  
Xue Jun Wang ◽  
Sheng Ming Xu
Keyword(s):  
Solvent Extraction ◽  
Raw Materials ◽  
Low Cost ◽  
Rapid Development ◽  
Li Ion Batteries ◽  
Active Materials ◽  
Solid Ratio ◽  
Li Ion ◽  
Leaching Condition ◽  
Addition Amount

With the rapid development and wide application of Li-ion batteries, cathode materials containing value metals Co, Ni and Mn are blended by several kind of metal oxide presently for pursuing high safe stability and low cost. The composition of spent Li-ion batteries has become complicated and optimum leaching condition varied. In this paper, leaching process for the mixture of pure LiCoO2and Li (Ni1/3Co1/3Mn1/3)O2was studied. With an increase in component of LiCoO2in mixed materials, the optimum leaching condition varied as: temperature from 60°C to 90°C, H2O2addition amount from 0.54 to 0.75ml/g and liquid-solid ratio from 10 to 20. According to this result, a real mixed spent batteries materials was recovered by being leached in 2M H2SO4at temperature of 90°C, liquid-solid ratio 20 and 0.6ml/g H2O2added. The leaching efficiencies of Co, Ni, Mn, Li were 96.88%, 93.71%, 92.12%, 99.43% respectively. Cu, Al and Fe in solution were removed by precipitation and solvent extraction. Finally, Ni, Co, Mn were extracted by D2EHPA for separating with Na+and other impurities, which is used as a raw materials for preparation of cathode active materials in batteries.

scholarly journals Impact of Surface Chemistry of Silicon Nanoparticles on the Structural and Electrochemical Properties of Si/Ni3.4Sn4 Composite Anode for Li-Ion Batteries

Nanomaterials ◽  
2020 ◽  
Vol 11 (1) ◽  
pp. 18
Author(s):  
Tahar Azib ◽  
Claire Thaury ◽  
Fermin Cuevas ◽  
Eric Leroy ◽  
Christian Jordy ◽  
...  
Keyword(s):  
Surface Chemistry ◽  
Electrochemical Properties ◽  
Large Scale ◽  
Silicon Nanoparticles ◽  
Lithium Ion ◽  
Li Ion Batteries ◽  
Chemical Homogeneity ◽  
Electrochemical Behaviors ◽  
Pure Silicon ◽  
Li Ion

Embedding silicon nanoparticles in an intermetallic matrix is a promising strategy to produce remarkable bulk anode materials for lithium-ion (Li-ion) batteries with low potential, high electrochemical capacity and good cycling stability. These composite materials can be synthetized at a large scale using mechanical milling. However, for Si-Ni3Sn4 composites, milling also induces a chemical reaction between the two components leading to the formation of free Sn and NiSi2, which is detrimental to the performance of the electrode. To prevent this reaction, a modification of the surface chemistry of the silicon has been undertaken. Si nanoparticles coated with a surface layer of either carbon or oxide were used instead of pure silicon. The influence of the coating on the composition, (micro)structure and electrochemical properties of Si-Ni3Sn4 composites is studied and compared with that of pure Si. Si coating strongly reduces the reaction between Si and Ni3Sn4 during milling. Moreover, contrary to pure silicon, Si-coated composites have a plate-like morphology in which the surface-modified silicon particles are surrounded by a nanostructured, Ni3Sn4-based matrix leading to smooth potential profiles during electrochemical cycling. The chemical homogeneity of the matrix is more uniform for carbon-coated than for oxygen-coated silicon. As a consequence, different electrochemical behaviors are obtained depending on the surface chemistry, with better lithiation properties for the carbon-covered silicon able to deliver over 500 mAh/g for at least 400 cycles.

scholarly journals Interfacial Manipulation via In-Situ Grown ZnSe Overlayer toward Highly Reversible Zn Metal Anodes

2021 ◽  
Author(s):  
Xianzhong Yang ◽  
Chao Li ◽  
Zhongti Sun ◽  
Shuai Yang ◽  
Zixiong Shi ◽  
...  
Keyword(s):  
Large Scale ◽  
Coulombic Efficiency ◽  
Low Cost ◽  
Chemical Vapor ◽  
Side Reactions ◽  
Water Penetration ◽  
Metal Anode ◽  
Zn Anode ◽  
Manipulation Strategy

Abstract Zn metal anode has garnered growing scientific and industrial interest owing to its appropriate redox potential, low cost and good safety. Nevertheless, the instability of Zn metal, caused by dendrite formation, hydrogen evolution and side reactions, gives rise to poor electrochemical stability and unsatisfactory cycling life, greatly hampering large-scale utilization. Herein, an in-situ grown ZnSe layer with controllable thickness is crafted over one side of commercial Zn foil via chemical vapor deposition, aiming to achieve optimized interfacial manipulation between aqueous electrolyte/Zn anode. Thus-derived ZnSe overlayer not only prevents water penetration and restricts Zn2+ two-dimensional diffusion, but also homogenizes the electric field at the interface and facilitates favorable (002) plane growth of Zn. As a result, dendrite-free and homogeneous Zn deposition is obtained; side reactions are concurrently inhibited. In consequence, a high Coulombic efficiency of 99.2% and high cyclic stability for 860 cycles at 1.0 mA cm–2 in symmetrical cells is harvested. Meanwhile, when paired with V2O5 cathode, assembled full cell achieves an outstanding initial capacity (200 mAh g–1) and elongated lifespan (a capacity retention of 84% after 1000 cycles) at 5.0 A g–1. Our highly reversible Zn anode enabled by the interfacial manipulation strategy is anticipated to satisfy the demand of industrial and commercial use.

Ternary Cu2SnS3 cabbage-like nanostructures: large-scale synthesis and their application in Li-ion batteries with superior reversible capacity

Nanoscale ◽  
2011 ◽  
Vol 3 (10) ◽  
pp. 4389 ◽  
Author(s):  
Baihua Qu ◽  
Hongxing Li ◽  
Ming Zhang ◽  
Lin Mei ◽  
Libao Chen ◽  
...  
Keyword(s):  
Large Scale ◽  
Reversible Capacity ◽  
Li Ion Batteries ◽  
Li Ion ◽  
Large Scale Synthesis

Cu-ion induced self-polymerization of Cu phthalocyanine to prepare low-cost organic cathode materials for Li-ion batteries with ultra-high voltage and ultra-fast rate capability

2021 ◽  
Author(s):  
Haichang Zhang ◽  
Rui Zhang ◽  
Xingjiang Liu ◽  
Fei Ding ◽  
Chunsheng Shi ◽  
...  
Keyword(s):  
High Voltage ◽  
Cathode Materials ◽  
Fast Rate ◽  
Low Cost ◽  
Rate Capability ◽  
Li Ion Batteries ◽  
Practical Application ◽  
Battery Materials ◽  
Li Ion ◽  
Synthesis Routes

High cost, complex synthesis routes and low yield are pressing challenges hindering the practical application of organic battery materials. Herein, copper(II) phthalocyanine (CuPc), one of the most frequently used blue...

Sign in / Sign up

Export Citation Format

Share Document