Research and Application on High Efficiency Reversible Cutting Technique

2004 ◽  
Vol 471-472 ◽  
pp. 825-829
Author(s):  
Wen Ge Wu ◽  
Si Qin Pang ◽  
Qi Xun Yu
Keyword(s):  
High Efficiency ◽  
Cutting Tool ◽  
Handling Time ◽  
Cutting Parameters ◽  
Machining Process ◽  
Processing Route ◽  
Rough Machining ◽  
Machined Surface ◽  
Primary Motion ◽  
The Way

Reversible cutting method is a research thesis proposed to shorten processing route, decrease tool number and handling time, increase machining efficiency. There are three movement ways, i.e. reversible feed motion, reversible primary motion and reversible composite motion. Primary motion is done by workpiece, conventional or reversible feed motion is done by cutting tool in the way of reversible feed motion, e.g. turning. Cutting velocity is passed to cutting tool, clockwise or anti-clockwise cutting movement is done by cutting tool in the way of reversible primary motion, e.g. milling, shaping, drilling (spade drill), reaming. Primary and feed motions are all reversible in composite motion, e.g. turn-milling. Chip deformation and machined surface with reversible finishing is discussed. A mechanical analysis is carried out to the workpiece deformation of slender shaft turning in normal direction and reversible direction. The result has been verified by experiments. Experimental data for the range of cutting parameters tested showed that the reversible fine machining produce the compressive residual stresses at the surface, which are critical in the performance of the machined components. Experimental research indicted that the results of micro-hardness of reversible fine machining technique are smaller than that of general fine machining show that decreased plastic deformation of the surface layer and work-hardening. It can be adopted such planning which rough machining during advance stroke and fine machining during return stroke in machining process.

Analysis of Reversible Fine Machining Sequence Effect on Surface Integrity

2006 ◽  
Vol 315-316 ◽  
pp. 391-395
Author(s):  
Wen Ge Wu ◽  
Si Qin Pang ◽  
Zhan Qiang Liu
Keyword(s):  
Surface Roughness ◽  
Residual Stresses ◽  
Surface Integrity ◽  
Machining Process ◽  
Processing Route ◽  
Machining Accuracy ◽  
Machining Efficiency ◽  
Micro Hardness ◽  
Rough Machining ◽  
Machined Surface

Reversible cutting method is a new research thesis proposed to shorten processing route, decrease tool number and handling time, increase machining efficiency. The aim of the presented work was to analysis the effects of reversible fine machining sequence on surface integrity in machined layer. Nonlinear hardening during reverse loading and the change of the Bauschinger effect factor with plastic strain were properly taken into account. In experiments, the residual stresses have been measured using the X-ray diffraction technique (at the surface of the workpiece and in depth). Moreover, micro-hardness and surface roughness of machined surface are presented. Experimental data for the range of cutting parameters tested showed that the reversible fine machining produce the tensile residual stresses at the surface, which are critical in the performance of the machined components. The experimental results of micro-hardness of reversible fine machining technique are smaller than that of general fine machining show that decreased plastic deformation of the surface layer and work-hardening. Surface roughness of machined surface with reversible finishing is discussed. Research results indicted that it can be adopted such planning which rough machining during advance stroke and fine machining or semi-finishing during return stroke in machining process. In this way, it has such advantages that increase machining efficiency and machining accuracy, decrease bending deformation.

Surface Roughness and Cutting Force Components Evaluation in Hard Turning by Differently Shaped Cutting Tools

2016 ◽  
Vol 862 ◽  
pp. 26-32 ◽  
Author(s):  
Michaela Samardžiová
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Hard Turning ◽  
Cutting Tool ◽  
Single Point ◽  
Machining Process ◽  
Tool Geometry ◽  
Machined Surface ◽  
Cutting Force Components ◽  
Force Components

There is a difference in machining by the cutting tool with defined geometry and undefined geometry. That is one of the reasons of implementation of hard turning into the machining process. In current manufacturing processes is hard turning many times used as a fine finish operation. It has many advantages – machining by single point cutting tool, high productivity, flexibility, ability to produce parts with complex shapes at one clamping. Very important is to solve machined surface quality. There is a possibility to use wiper geometry in hard turning process to achieve 3 – 4 times lower surface roughness values. Cutting parameters influence cutting process as well as cutting tool geometry. It is necessary to take into consideration cutting force components as well. Issue of the use of wiper geometry has been still insufficiently researched.

Holes Machining Process Optimization with Genetic Algorithm

2011 ◽  
Vol 460-461 ◽  
pp. 117-122 ◽  
Author(s):  
Guang Yu Zhu ◽  
Lian Fang Chen
Keyword(s):  
Genetic Algorithm ◽  
Cutting Tool ◽  
Machining Process ◽  
Processing Route ◽  
Optimal Route ◽  
Optimal Processing ◽  
Global Optimal ◽  
Level Method ◽  
Multi Level ◽  
Changing Times

In this paper, a multi-level method has been adopted to optimize the holes machining process with genetic algorithm (GA). Based on the analyzing of the features of the part with multi-holes, the local optimal processing route for the holes with the same processing feature is obtained with GA, then try to obtain the global optimal route with GA by considering the obtained local optimal route and the holes with different features. That is what the multi-level method means. The optimal route means the minimum moving length of the cutting tool and the minimum changing times of the cutting tool. The experiment is carried out to verify the algorithm and the proposed method, and result indicates that with GA and using the multi-level method the optimal holes machining route can be achieved efficiently.

A novel approach to machining process fault detection using unsupervised learning

2020 ◽  
pp. 095440542093755
Author(s):  
Thomas McLeay ◽  
Michael S Turner ◽  
Keith Worden
Keyword(s):  
Fault Detection ◽  
Unsupervised Learning ◽  
Tool Path ◽  
Cutting Tool ◽  
Novelty Detection ◽  
Cutting Parameters ◽  
Machining Process ◽  
Machining Processes ◽  
Workpiece Material ◽  
Data Set

The most common machining processes of turning, drilling, milling and grinding concern the removal of material from a workpiece using a cutting tool. The performance of machining processes depends on a number of key method parameters, including cutting tool, workpiece material, machine configuration, fixturing, cutting parameters and tool path trajectory. The large number of possible configurations can make it difficult to implement fault detection systems without having to train the system to a particular method or fault type. The research of this article applies a novel method to detect the changing state of a process over time in order to detect faulty machining conditions such as worn tools and cutting depth changes. Unlike studies in the previous literature in this domain, an unsupervised learning method is used, so that the method can be applied in production to unfamiliar processes or fault conditions. In the case presented, novelty detection is applied to a multivariate sensor feature data set obtained from a milling process. Sensor modalities include acoustic emission, vibration and spindle power and time and frequency domain features are employed. The Mahalanobis squared-distance is used to measure discordancy of each new data point, and values that exceed a principled novelty threshold are categorised as fault conditions.

Designing and implementation of a novel online adaptive control with optimization technique in hard turning

2020 ◽  
pp. 095965182095219
Author(s):  
Vahid Pourmostaghimi ◽  
Mohammad Zadshakoyan
Keyword(s):  
Adaptive Control ◽  
Tool Wear ◽  
Hard Turning ◽  
Cutting Tool ◽  
Optimization Technique ◽  
Cutting Parameters ◽  
Numerical Control ◽  
Machining Process ◽  
Machining Parameters ◽  
Optimization Methodology

Determination of optimum cutting parameters is one of the most essential tasks in process planning of metal parts. However, to achieve the optimal machining performance, the cutting parameters have to be regulated in real time. Therefore, utilizing an intelligent-based control system, which can adjust the machining parameters in accordance with optimal criteria, is inevitable. This article presents an intelligent adaptive control with optimization methodology to optimize material removal rate and machining cost subjected to surface quality constraint in finish turning of hardened AISI D2 considering the real condition of the cutting tool. Wavelet packet transform of cutting tool vibration signals is applied to estimate tool wear. Artificial intelligence techniques (artificial neural networks, genetic programming and particle swarm optimization) are used for modeling of surface roughness and tool wear and optimization of machining process during hard turning. Confirmatory experiments indicated that the efficiency of the proposed adaptive control with optimization methodology is 25.6% higher compared to the traditional computer numerical control turning systems.

High Efficiency Machining for Integral Shaping from Simplicity Materials Using Five-Axis Machine Tools

2016 ◽  
Vol 10 (5) ◽  
pp. 804-812 ◽  
Author(s):  
Makoto Yamada ◽  
◽  
Tsukasa Kondo ◽  
Kai Wakasa
Keyword(s):  
Machine Tools ◽  
High Speed ◽  
High Efficiency ◽  
Cutting Process ◽  
Machining Process ◽  
Rough Machining ◽  
Convex Shape ◽  
Simple Material ◽  
Voxel Model ◽  
Five Axis

In the integrally shaping process from a simple material shape to an objective shape, it is necessary to reduce the time required for the machining process in order to improve cost savings and the effectiveness of mass production. For the purpose of achieving high efficiency in the integral shaping from simplicity materials, we have focused on a rough cutting process that requires the most time in the manufacturing process. The purpose of this research is to propose a method for realizing high-speed rough machining using five-axis machine tools with a voxel model, and confirm the high efficiency of the rough cutting. In this research, we use five-axis controlled machine tools for material machining, and suggest two machining methods for the rough cutting process using the voxel model. The first method derives the tool posture where the cutting removal quantity becomes the maximum; this method also carries out a rough cutting process via 3+2 axis controlled machining. The other method carries a complete convex shape that includes the required shape, and simultaneously machines via five-axis machining based on the complete convex shape. This paper demonstrates the 3+2 axis control machining method that uses the voxel model to perform the rough machining process with high efficiency, and the simultaneous five-axis control machining method that uses a complete convex shape model for rough machining. We confirm the results with a computer simulation and actual machining experiments.

Experimental Research on Superlong Deep-Hole Drilling Processing Technology for Steel of 4145H Drill Collar

2011 ◽  
Vol 201-203 ◽  
pp. 2597-2600
Author(s):  
Zhan Feng Liu ◽  
Rui Liang Li
Keyword(s):  
Cutting Tool ◽  
Cutting Tools ◽  
Tool Material ◽  
Cutting Parameters ◽  
Machining Process ◽  
Hole Drilling ◽  
Deep Hole ◽  
Actual Structure ◽  
Steel Processing ◽  
Drill Collar

Through the analysis for steel of 4145H drill collar, Research into the various factors of cutting, such as the cutting tool material, cutting-tool angle and cutting parameters, combined with the actual structure of the workpiece and the superlong deep-hole processing method for study. In the test, the machining process is analyzed, especially the process of boring and honing. The test result indicates that the trepanning process is stable and reliable to solve the superlong deep hole (Φ71mm×7500mm) of 4145H drill collar steel processing problems of production if the optimizing cutting method is appropriate and the cutting tools and the cutting parameters are rational.

The Effect of the Cutting Parameters on the Machined Surface Roughness

2017 ◽  
Vol 260 ◽  
pp. 219-226 ◽  
Author(s):  
Viktors Gutakovskis ◽  
Eriks Gerins ◽  
Janis Rudzitis ◽  
Artis Kromanis
Keyword(s):  
Surface Roughness ◽  
Metal Cutting ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Cutting Parameters ◽  
Cutting Process ◽  
Tool Geometry ◽  
Machining Parameters ◽  
Machined Surface ◽  
Machined Surface Roughness

From the invention of turning machine or lathe, some engineers are trying to increase the turning productivity. The increase of productivity is following after the breakout in instrumental area, such as the hard alloy instrument and resistance to wear cutting surfaces. The potential of cutting speed has a certain limit. New steel marks and cutting surfaces types allow significantly increase cutting and turning speeds. For the most operation types the productivity increase begins from the feeding increase. But the increase of feeding goes together with machined surface result decreasement. Metal cutting with high feeding is one of the most actual problems in the increasing of manufacturing volume but there are some problems one of them is the cutting forces increasement and larger metal removal rate, which decrease the cutting tool life significantly. Increasing of manufacturing volume, going together with the cutting instrument technology and material evolution, such as the invention of the carbide cutting materials and wear resistant coatings such as TiC and Ti(C,N). Each of these coating have its own properties and functions in the metal cutting process. Together with this evolution the cutting tool geometry and machining parameters dependencies are researched. Traditionally for the decreasing the machining time of one part, the cutting parameters were increased, decreasing by this way the machining operation quantity. In our days the wear resistance of the cutting tools increasing and it is mostly used one or two machining operations (medium and fine finishing). The purpose of the topic is to represent the experimental results of the stainless steel turning process, using increased cutting speeds and feeding values, to develop advanced processing technology, using new modern coated cutting tools by CVD and PVD methods. After investigation of the machined surface roughness results, develop the mathematical model of the cutting process using higher values of the cutting parameters.

Impact of Cutting Speed on the Resultant Cutting Tools Durability in Turning Process of Steel 100CrMn6

2014 ◽  
Vol 616 ◽  
pp. 292-299
Author(s):  
Ján Duplák ◽  
Peter Michalik ◽  
Miroslav Kormoš ◽  
Slavko Jurko ◽  
Pavel Kokuľa ◽  
...  
Keyword(s):  
Cutting Tool ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Machining Process ◽  
Turning Process ◽  
Machine Material ◽  
Actual Production ◽  
Real Behavior ◽  
Optimization Of Cutting Parameters

Durability of cutting tools represent to a large spectral index on the basis of which is characterized by functional work. Every manufacturer of cutting tools before the actual production of these tools during the development make a tests and prescribing them characteristics on which is possible then to predict their behavior in the actual production process. It might be argued, that these information are optimized and ideal and therefore the information which producers sells by these cutting tools, do not correspond completely with their real behavior. It is necessary that information by using experiments to verify and then review their informative value and correctness. Durability of cutting tools is often indicated for one tested material of marketing aspect, which is machined and effort of user is to achieve this variable for other machined materials, then is happened problem in the production. The problem is very short lifetime of cutting tool in machining process, where the effect is impossibility to optimize the machining process. The results of this action are excesses time caused by exchanged of cutting plate and then it is make a low production of machining industry by setting of machines, and then the factory has an economical loses. This article is focused on tested of cutting tools made by sintered carbide, where the machine material is steel 100CrMn6. This type of steel is used by manufacturer of bearings, therefore the experimental part of this article should be a helper for machining manufactures, which make effectively manage with tools by optimization of cutting parameters of cutting tools and thus increase their productivity and to achieve a higher profits.

Research on the Rough Cut of Heavy Pressure Vessels

2010 ◽  
Vol 129-131 ◽  
pp. 276-279
Author(s):  
Xu Li ◽  
Geng Huang He ◽  
Bin Du Hong ◽  
Hui Cai Zhao
Keyword(s):  
Pressure Vessel ◽  
Tool Material ◽  
Cutting Parameters ◽  
Pressure Vessels ◽  
Machining Efficiency ◽  
Rough Machining ◽  
Machined Surface ◽  
Large Size ◽  
Production Period ◽  
Rough Cut

The blank of heavy pressure vessel is forged directly, so its machined surface is very terrible. Because of its very large size and weight, it costs very much time and expenses cost, lots of tools and activity float to turn it during the period of rough machining. This paper describes the machining characteristic of the machining difficult points of heavy pressure vessel in China. Through analyzing the processing difficulties and utilizing the methods of experimentation and manufacture, it discussed on the choice of cutting parameters, tool structure and the optimization of tool material and so on. Then the effective measures of rough machining efficiency were constituted. Last, the processing plan which is summarized turns into the guidance of the heavy pressure vessel in actual production period.

Sign in / Sign up

Export Citation Format

Share Document