Experimental Research on Superlong Deep-Hole Drilling Processing Technology for Steel of 4145H Drill Collar

2011 ◽  
Vol 201-203 ◽  
pp. 2597-2600
Author(s):  
Zhan Feng Liu ◽  
Rui Liang Li
Keyword(s):  
Cutting Tool ◽  
Cutting Tools ◽  
Tool Material ◽  
Cutting Parameters ◽  
Machining Process ◽  
Hole Drilling ◽  
Deep Hole ◽  
Actual Structure ◽  
Steel Processing ◽  
Drill Collar

Through the analysis for steel of 4145H drill collar, Research into the various factors of cutting, such as the cutting tool material, cutting-tool angle and cutting parameters, combined with the actual structure of the workpiece and the superlong deep-hole processing method for study. In the test, the machining process is analyzed, especially the process of boring and honing. The test result indicates that the trepanning process is stable and reliable to solve the superlong deep hole (Φ71mm×7500mm) of 4145H drill collar steel processing problems of production if the optimizing cutting method is appropriate and the cutting tools and the cutting parameters are rational.

Experimental Research on Superlong Deep-Hole Drilling Processing Technology for Beryllium Bronze

2011 ◽  
Vol 130-134 ◽  
pp. 1634-1637 ◽  
Author(s):  
Zhan Feng Liu ◽  
Rui Liang Li
Keyword(s):  
Heat Treatment ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Tool Material ◽  
Cutting Parameters ◽  
Processing Method ◽  
Hole Drilling ◽  
Deep Hole ◽  
Actual Structure ◽  
Beryllium Bronze

According to the material properties and the cutting performance of beryllium bronze, research into the various factors of cutting, such as the materials heat treatment, the cutting tool material, cutting-tool angle and the cutting parameters, combined with the actual structure of the workpiece and the overlong deep-hole processing method for study. The test proved that selected reasonable heat treatment , processing methods, cutting tools and cutting parameters can be solved Φ12mm × 4000mm overlong deep-hole processing problems of the beryllium bronze.

scholarly journals Temperature monitoring in the subsurface during single lip deep hole drilling

2020 ◽  
Vol 87 (12) ◽  
pp. 757-767
Author(s):  
Robert Wegert ◽  
Vinzenz Guski ◽  
Hans-Christian Möhring ◽  
Siegfried Schmauder
Keyword(s):  
Cutting Parameters ◽  
Drill Hole ◽  
Machining Process ◽  
Hole Drilling ◽  
Drilling Process ◽  
Deep Hole ◽  
Machining Processes ◽  
Deep Hole Drilling ◽  
Feed Force ◽  
Cutting Zone

AbstractThe surface quality and the subsurface properties such as hardness, residual stresses and grain size of a drill hole are dependent on the cutting parameters of the single lip deep hole drilling process and therefore on the thermomechanical as-is state in the cutting zone and in the contact zone between the guide pads and the drill hole surface. In this contribution, the main objectives are the in-process measurement of the thermal as-is state in the subsurface of a drilling hole by means of thermocouples as well as the feed force and drilling torque evaluation. FE simulation results to verify the investigations and to predict the thermomechanical conditions in the cutting zone are presented as well. The work is part of an interdisciplinary research project in the framework of the priority program “Surface Conditioning in Machining Processes” (SPP 2086) of the German Research Foundation (DFG).This contribution provides an overview of the effects of cutting parameters, cooling lubrication and including wear on the thermal conditions in the subsurface and mechanical loads during this machining process. At first, a test set up for the in-process temperature measurement will be presented with the execution as well as the analysis of the resulting temperature, feed force and drilling torque during drilling a 42CrMo4 steel. Furthermore, the results of process simulations and the validation of this applied FE approach with measured quantities are presented.

Hardened Steel Turning by Means of Modern CBN Cutting Tools

2013 ◽  
Vol 581 ◽  
pp. 188-193 ◽  
Author(s):  
Łukasz Ślusarczyk ◽  
Grzegorz Struzikiewicz
Keyword(s):  
Cutting Tool ◽  
Cutting Tools ◽  
Tool Material ◽  
Chip Morphology ◽  
Cutting Parameters ◽  
Hardened Steel ◽  
Cutting Depth ◽  
Cutting Rate ◽  
Steel Turning ◽  
The Impact

The paper presents an analysis of the impact of cutting parameters such as cutting rate, feed rate, cutting depth and cutting tool material grade for surface roughness, the components of the total cutting force and chip morphology. We analysed the process of rolling 145Cr steel with a hardness of 55HRC with Wiper type tools with different percentage of CBN. The results and conclusions were presented.

Impact of Cutting Speed on the Resultant Cutting Tools Durability in Turning Process of Steel 100CrMn6

2014 ◽  
Vol 616 ◽  
pp. 292-299
Author(s):  
Ján Duplák ◽  
Peter Michalik ◽  
Miroslav Kormoš ◽  
Slavko Jurko ◽  
Pavel Kokuľa ◽  
...  
Keyword(s):  
Cutting Tool ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Machining Process ◽  
Turning Process ◽  
Machine Material ◽  
Actual Production ◽  
Real Behavior ◽  
Optimization Of Cutting Parameters

Durability of cutting tools represent to a large spectral index on the basis of which is characterized by functional work. Every manufacturer of cutting tools before the actual production of these tools during the development make a tests and prescribing them characteristics on which is possible then to predict their behavior in the actual production process. It might be argued, that these information are optimized and ideal and therefore the information which producers sells by these cutting tools, do not correspond completely with their real behavior. It is necessary that information by using experiments to verify and then review their informative value and correctness. Durability of cutting tools is often indicated for one tested material of marketing aspect, which is machined and effort of user is to achieve this variable for other machined materials, then is happened problem in the production. The problem is very short lifetime of cutting tool in machining process, where the effect is impossibility to optimize the machining process. The results of this action are excesses time caused by exchanged of cutting plate and then it is make a low production of machining industry by setting of machines, and then the factory has an economical loses. This article is focused on tested of cutting tools made by sintered carbide, where the machine material is steel 100CrMn6. This type of steel is used by manufacturer of bearings, therefore the experimental part of this article should be a helper for machining manufactures, which make effectively manage with tools by optimization of cutting parameters of cutting tools and thus increase their productivity and to achieve a higher profits.

scholarly journals VARIASI KECEPATAN PEMOTONGAN PROSES PEMBUBUTAN BAJA AISI 4140 TERHADAP KEAUSAN DAN UMUR MATA PAHAT KARBIDA

POROS ◽  
2021 ◽  
Vol 17 (1) ◽  
pp. 26
Author(s):  
Sobron Y. Lubis ◽  
Sofyan Djamil ◽  
Adianto Adianto ◽  
Amor Santosa ◽  
Edric VM.
Keyword(s):  
Cutting Tool ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Machining Process ◽  
Aisi 4140 Steel ◽  
Steel Material ◽  
Aisi 4140 ◽  
Edge Wear ◽  
Coated Carbide

In the machining process, increased production can be done by increasing the use of cuttingparameters. However, the use of high cutting parameters has an effect on the wear of the cutting toolused. The aim of this research is to analyze the wear and tear that occurs on cutting tools and tool lifewhen cutting AISI 4140 steel by using variations in cutting speed. The machining process uses a CNClathe by turning the surface of the AISI 4140 steel workpiece. The wear criteria are determined when thecutting tool has reached the edge wear limit (VB) of 0.3 mm. Observation and measurement of carbidecutting tools are carried out every 5 minutes the machining process is carried out. If the cutting tool hasnot shown the specified wear value, then the cutting tool then cuts, so that the wear value is obtained.From the research conducted it was found that at a cutting speed of 160 m / min the cutting tool iscapable of cutting for 39 minutes, 13 seconds. At a cutting speed of 180 m / min the cutting tool is capableof cutting for 38 minutes, 14 seconds. At a cutting speed of 200 m / min the cutting tool is capable ofcutting for 33 minutes, 8 seconds. At a cutting speed of 240 m / min the cutting tool is capable of cuttingfor 26 minutes, 3 seconds. Taylor's advanced tool life for the coated carbide cutting tool in turning AISI4140 steel material is: Vc. Tl.0.073 = 8203.

Research on Technology Test of 304 Stainless Steel Super Long Deep-Hole Drilling

2013 ◽  
Vol 774-776 ◽  
pp. 1137-1140 ◽  
Author(s):  
Zhan Feng Liu ◽  
Meng Xu
Keyword(s):  
Stainless Steel ◽  
Cutting Tools ◽  
Cutting Parameters ◽  
304 Stainless Steel ◽  
Hole Drilling ◽  
Tool Geometry ◽  
Drilling Process ◽  
Deep Hole ◽  
Deep Hole Drilling ◽  
Material Tool

In this paper, through the analysis of 304 stainless steel to elaborate the influence of various factors in the process of drilling from the blade material,tool geometry parameters,cutting parameters and drilling methods.It is proved by selecting reasonable processing, cutting tools and cutting parameters (Φ50mm × 4700mm) 304 stainless steel parts of the drilling process issues can be resolved.

scholarly journals Evaluation of Cutting-Tool Coating on the Surface Roughness and Hole Dimensional Tolerances during Drilling of Al6061-T651 Alloy

Materials ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1783
Author(s):  
Hamza A. Al-Tameemi ◽  
Thamir Al-Dulaimi ◽  
Michael Oluwatobiloba Awe ◽  
Shubham Sharma ◽  
Danil Yurievich Pimenov ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Cutting Tool ◽  
Good Practice ◽  
Cutting Tools ◽  
Statistical Design ◽  
Cutting Parameters ◽  
Statistical Design Of Experiments ◽  
Hole Quality ◽  
Coated Tools ◽  
Tool Coating

Aluminum alloys are soft and have low melting temperatures; therefore, machining them often results in cut material fusing to the cutting tool due to heat and friction, and thus lowering the hole quality. A good practice is to use coated cutting tools to overcome such issues and maintain good hole quality. Therefore, the current study investigates the effect of cutting parameters (spindle speed and feed rate) and three types of cutting-tool coating (TiN/TiAlN, TiAlN, and TiN) on the surface finish, form, and dimensional tolerances of holes drilled in Al6061-T651 alloy. The study employed statistical design of experiments and ANOVA (analysis of variance) to evaluate the contribution of each of the input parameters on the measured hole-quality outputs (surface-roughness metrics Ra and Rz, hole size, circularity, perpendicularity, and cylindricity). The highest surface roughness occurred when using TiN-coated tools. All holes in this study were oversized regardless of the tool coating or cutting parameters used. TiN tools, which have a lower coating hardness, gave lower hole circularity at the entry and higher cylindricity, while TiN/TiAlN and TiAlN seemed to be more effective in reducing hole particularity when drilling at higher spindle speeds. Finally, optical microscopes revealed that a built-up edge and adhesions were most likely to form on TiN-coated tools due to TiN’s chemical affinity and low oxidation temperature compared to the TiN/TiAlN and TiAlN coatings.

scholarly journals Effect of Cutting Parameters and Tool Geometry on the Performance Analysis of One-Shot Drilling Process of AA2024-T3

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 854
Author(s):  
Muhammad Aamir ◽  
Khaled Giasin ◽  
Majid Tolouei-Rad ◽  
Israr Ud Din ◽  
Muhammad Imran Hanif ◽  
...  
Keyword(s):  
Feed Rate ◽  
Surface Defects ◽  
Thrust Force ◽  
Cutting Tools ◽  
Chip Thickness ◽  
Cutting Parameters ◽  
Spindle Speed ◽  
Machining Process ◽  
Tool Geometry ◽  
Drilling Process

Drilling is an important machining process in various manufacturing industries. High-quality holes are possible with the proper selection of tools and cutting parameters. This study investigates the effect of spindle speed, feed rate, and drill diameter on the generated thrust force, the formation of chips, post-machining tool condition, and hole quality. The hole surface defects and the top and bottom edge conditions were also investigated using scan electron microscopy. The drilling tests were carried out on AA2024-T3 alloy under a dry drilling environment using 6 and 10 mm uncoated carbide tools. Analysis of Variance was employed to further evaluate the influence of the input parameters on the analysed outputs. The results show that the thrust force was highly influenced by feed rate and drill size. The high spindle speed resulted in higher surface roughness, while the increase in the feed rate produced more burrs around the edges of the holes. Additionally, the burrs formed at the exit side of holes were larger than those formed at the entry side. The high drill size resulted in greater chip thickness and an increased built-up edge on the cutting tools.

Wear of Coated Cutting Tool Based on AdvantEdge

2014 ◽  
Vol 551 ◽  
pp. 221-227
Author(s):  
Zhi Qiang Zhang ◽  
Tie Qiang Gang ◽  
Yi Kai Yi
Keyword(s):  
Wear Rate ◽  
Coating Thickness ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Simulation Software ◽  
Machining Process ◽  
Sliding Velocity ◽  
Coating Materials ◽  
Element Simulation ◽  
Coated Tool

In this paper, based on finite element simulation software AdvantEdge, the effects of different coating materials and thickness on the wear of cutting tools during the machining process have been studied. For the tools with coating materials of TiAlN, Al2O3, TiN, TiC, we can calculate the wear rate according to the Usui mathematical model of tool wear, and then consider thickness factor of TiC coating. Because of the lowest thermal conductivity, the workpiece cut by TiC coated tool will soften first and more over cutting time, it result in the lowest wear rate. And with the increase of coating thickness, the effect of "thermal barrier" is more obvious for the relatively thicker coating tool, but the relative sliding velocity between the chip and tool is increasing meanwhile, so a suitable coating thickness is necessary.

Forecasting Performance of Ceramic Cutting Tool

2017 ◽  
Vol 736 ◽  
pp. 86-90 ◽  
Author(s):  
Vyacheslav Maksarov ◽  
A. Khalimonenko
Keyword(s):  
Electrical Resistance ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Tool Material ◽  
Ceramic Materials ◽  
Specific Electrical Resistance ◽  
Testing Methods ◽  
Microstructural Parameters ◽  
Forecasting Performance ◽  
Nondestructive Testing Methods

The article considers the problems of forecasting the performance of cutting tools equipped with replaceable ceramic cutting bits. It is proposed to forecast the operability of ceramic tools on the ground of dependence between its performance characteristics and the microstructural parameters of the tool material. It is proposed to determine the parameters of ceramic bits microstructure by a nondestructive testing methods based on measuring the specific electrical resistance of ceramic materials. As a result of the study we have undertaken, a relationship was detected between the performance and specific electrical resistance of ceramic cutting tools.

Sign in / Sign up

Export Citation Format

Share Document