Fabrication and Thermoelectric Properties of N-Type Bi2Te3 Based Compounds by Spark Plasma Sintering

2005 ◽  
Vol 486-487 ◽  
pp. 253-256 ◽  
Author(s):  
D.M. Lee ◽  
Cheol Ho Lim ◽  
Dong Choul Cho ◽  
Seung Y. Shin ◽  
Won Seung Cho
Keyword(s):  
Thermal Conductivity ◽  
Electrical Resistivity ◽  
Spark Plasma Sintering ◽  
Thermoelectric Properties ◽  
Figure Of Merit ◽  
Bending Strength ◽  
Sintering Temperature ◽  
Powder Size ◽  
Plasma Sintering ◽  
Spark Plasma

N-type Bi2Te3 based thermoelectric compound was prepared by spark plasma sintering with a temperature range of 340~460°C and powder size of ~75㎛, 76~150㎛, 151~250㎛. Thermoelectric properties of the compound were measured as a function of the sintering temperature and powder size. With increasing sintering temperature, the electrical resistivity and thermal conductivity of the compound greatly changed because of the increase in relative density. The Seebeck coefficient and electrical resistivity were varied largely with increasing powder size. Therefore, the compound sintered at 460°C, with the powder of ~75㎛, showed a figure of merit of 2.44 x 10-3/K. Also, the bending strength was 75MPa.

Effect of Oxygen Content on Thermoelectric Properties of Sintered Bi-Te Based Compounds

2004 ◽  
Vol 449-452 ◽  
pp. 905-908 ◽  
Author(s):  
Dong Choul Cho ◽  
Cheol Ho Lim ◽  
D.M. Lee ◽  
Seung Y. Shin ◽  
Chung Hyo Lee
Keyword(s):  
Thermal Conductivity ◽  
Electrical Resistivity ◽  
Oxygen Content ◽  
Thermoelectric Properties ◽  
Figure Of Merit ◽  
Room Temperature ◽  
Air Atmosphere ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Effect Of Oxygen

The n-type thermoelectric materials of Bi2Te2.7Se0.3 doped with SbI3 were prepared by spark plasma sintering technique. The powders were ball-milled in an argon and air atmosphere. Then, powders were reduced in H2 atmosphere. Effects of oxygen content on the thermoelectric properties of Bi2Te2.7Se0.3 compounds have been investigated. Seebeck coefficient, electrical resistivity and thermal conductivity of the sintered compound were measured at room temperature. It was found that the effect of atmosphere during the powder production was remarkable and thermoelectric properties of sintered compound were remarkably improved by H2 reduction of starting powder. The obtained maximum figure of merit was 2.4 x 10-3/K.

Thermoelectric Properties of La-doped BaSi2 and (Ba,Sr)Si2 Solid Solutions

2007 ◽  
Vol 1044 ◽  
Author(s):  
Kohsuke Hashimoto ◽  
Ken Kurosaki ◽  
Hiroaki Muta ◽  
Shinsuke Yamanaka
Keyword(s):  
Thermal Conductivity ◽  
Solid Solution ◽  
Electrical Resistivity ◽  
Thermoelectric Properties ◽  
Figure Of Merit ◽  
Room Temperature ◽  
Dimensionless Figure Of Merit ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
La Doped

AbstractWe studied the thermoelectric properties of BaSi2 and SrSi2. The polycrystalline samples were prepared by spark plasma sintering (SPS). The electrical resistivity (ρ), Seebeck coefficient (S), and thermal conductivity (κ) were measured above room temperature. The maximum values of the dimensionless figure of merit (ZT) were 0.01 at 954 K for BaSi2 and 0.09 at 417 K for SrSi2. We tried to enhance the ZT values of BaSi2 and SrSi2 by prepareing and characterizing La-doped BaSi2 and (Ba,Sr)Si2 solid solution.

Spark Plasma Sintering Effect on Thermoelectric Properties of Nanostructured Bismuth Telluride Synthesized by High Energy Ball Milling

2020 ◽  
Vol 20 (6) ◽  
pp. 3902-3908
Author(s):  
Sandeep K. Pundir ◽  
Sukhvir Singh ◽  
Parveen Jain
Keyword(s):  
Thermal Conductivity ◽  
Ball Milling ◽  
Spark Plasma Sintering ◽  
Thermoelectric Properties ◽  
Bismuth Telluride ◽  
Figure Of Merit ◽  
High Energy ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Energy Ball

Thermoelectric properties of high energy ball milled nano structured bismuth telluride (Bi2Te3) have been reported. By high energy ball milling, alloyed bulk crystalline ingots crush into nanopowder and followed by spark plasma sintering (SPS), we have demonstrate high figure of merit (ZT) in bismuth telluride pellet samples. In this work systematic study carried out on three pellet samples of Bi2Te3, synthesized by high ball milling for the time period of 4 hours, 8 hours and 12 hours and followed by SPS at the same processing parameters. A peak value of dimensionless figure of merit of about 1.22 at the temperature of 473 K has been achieved for 8 hours ball milled pellet sample. This enhancement in ZT value is mostly due to decrease in thermal conductivity. Results of this study demonstrate that ball milling and SPS has a major effect in controlling the density of grain boundaries of Bi2Te3 nano particles, while the pressure exerted on the powder samples during SPS introduce stress at the boundaries of the crystallites. These disordered crystallite boundary regions exert scattering of thermal energy carriers which reduced the thermal conductivity of the materials.

Microstructure and Thermoelectric Properties of P-Type Bi0.5Sb1.5Te3 Compounds Prepared by Spark Plasma Sintering

2006 ◽  
Vol 510-511 ◽  
pp. 1122-1125
Author(s):  
Won Seung Cho ◽  
Dong Choul Cho ◽  
Cheol Ho Lim ◽  
C.H. Lee ◽  
Woon Suk Hwang ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Electrical Resistivity ◽  
Seebeck Coefficient ◽  
Spark Plasma Sintering ◽  
Hydrogen Reduction ◽  
Sintering Temperature ◽  
Reduction Process ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
P Type

The microstructure and thermoelectrical properties of the 4wt% Te doped p-type Bi0.5Sb1.5Te3 compounds, fabricated by using spark plasma sintering in the temperature ranging from 250°C to 350°C, were characterized. The density of the sintered compounds was increased to 99.2% of theoretical density by carrying out the consolidation at 350oC for 2 min. The Seebeck coefficient, thermal conductivity and electrical resistivity were dependent on hydrogen reduction process and sintering temperature. The Seebeck coefficient increased with reduction process while the electrical resisitivity significantly decreased. Also, the electrical resistivity decreased and thermal conductivity increased with sintering temperature. The results suggest that the carrier density and mobility vary with reduction process and sintering temperature. The highest figure of merit of 3.5×10-3/K was obtained for the compounds spark plasma sintered at 350°C for 2 min by using the hydrogen-reduced powders.

Synthesis and Thermoelectric Properties of N-Type Bi2Te2.7Se0.3 Compounds by Spark Plasma Sintering

2005 ◽  
Vol 486-487 ◽  
pp. 654-657
Author(s):  
Dong Choul Cho ◽  
Cheol Ho Lim ◽  
Ki Tae Kim ◽  
Seung Y. Shin ◽  
D.M. Lee ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Electrical Resistivity ◽  
Seebeck Coefficient ◽  
Thermoelectric Properties ◽  
Hydrogen Reduction ◽  
Sintering Temperature ◽  
Reduction Process ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Temperature Time

Thermoelectric properties of the spark plasma sintered n-type Bi2Te2.7Se0.3 compounds were characterized with the sintering temperature, time and hydrogen reduction process. The Seebeck coefficient, electrical resistivity and thermal conductivity were dependent on hydrogen reduction process as well as sintering temperature. The Seebeck coefficient and electrical resistivity decreased and thermal conductivity increased with reduction treatment and sintering temperature. The results suggest that the carrier density varies with the dissolved oxygen and Te vacancies generated during the pulverization process. The highest figure of merit of 3.11×10-3/K was obtained for the compounds spark plasma sintered at 460°C for 16min by using the reduced powders.

Effect of Spark Plasma Sintering on the Microstructure Evolution and Properties of M3:2 High-Speed Steel

2014 ◽  
Vol 788 ◽  
pp. 329-333
Author(s):  
Rui Zhou ◽  
Xiao Gang Diao ◽  
Jun Chen ◽  
Xiao Nan Du ◽  
Guo Ding Yuan ◽  
...  
Keyword(s):  
Powder Metallurgy ◽  
Spark Plasma Sintering ◽  
High Speed ◽  
Bending Strength ◽  
Sintering Temperature ◽  
High Speed Steel ◽  
Continuous Heating ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
The Impact

Effects of sintering temperatures on the microstructure and mechanical performance of SPS M3:2 high speed steel prepared by spark plasma sintering was studied. High speed steel sintering curve of continuous heating from ambient temperature to 1200°C was estimated to analyze the sintering processes and sintering temperature range. The sintering temperature within this range was divided into groups to investigate hardness, relative density and microstructure of M3:2 high-speed steel. Strip and quadrate carbides were observed inside the equiaxed grains. SPS sintering temperature at 900°C can lead to nearly full densification with grain size smaller than 20μm. The hardness and bending strength are higher than that of the conventionally powder metallurgy fabricated ones sintered at 1270°C. However, fracture toughness of the high speed steel is lower than that of the conventional powder metallurgy steels. This can be attributed to the shape and distribution of M6C carbides which reduce the impact toughness of high speed steels.

Fabrication of Bi-Te Based Thermoelectric Semiconductors by Using Hybrid Powders

2005 ◽  
Vol 297-300 ◽  
pp. 875-880
Author(s):  
Cheol Ho Lim ◽  
Ki Tae Kim ◽  
Yong Hwan Kim ◽  
Dong Choul Cho ◽  
Young Sup Lee ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Single Crystals ◽  
Thermoelectric Properties ◽  
Thermoelectric Materials ◽  
Figure Of Merit ◽  
Bending Strength ◽  
Mixing Ratio ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
P Type

P-type Bi0.5Sb1.5Te3 compounds doped with 3wt% Te were fabricated by spark plasma sintering and their mechanical and thermoelectric properties were investigated. The sintered compounds with the bending strength of more than 50MPa and the figure-of-merit 2.9×10-3/K were obtained by controlling the mixing ratio of large powders (PL) and small powders (PS). Compared with the conventionally prepared single crystal thermoelectric materials, the bending strength was increased up to more than three times and the figure-of-merit Z was similar those of single crystals. It is expected that the mechanical properties could be improved by using hybrid powders without degradation of thermoelectric properties.

scholarly journals Thermoelectric properties of Cu3SbSe3 with intrinsically ultralow lattice thermal conductivity

2014 ◽  
Vol 2 (38) ◽  
pp. 15829-15835 ◽  
Author(s):  
Kriti Tyagi ◽  
Bhasker Gahtori ◽  
Sivaiah Bathula ◽  
A. K. Srivastava ◽  
A. K. Shukla ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Solid State ◽  
Spark Plasma Sintering ◽  
Thermoelectric Properties ◽  
Solid State Reaction ◽  
Electrical Transport ◽  
Single Phase ◽  
Lattice Thermal Conductivity ◽  
Plasma Sintering ◽  
Spark Plasma

Intrinsically ultra-low thermal conductivity and electrical transport in single-phase Cu2SbSe3 synthesized employing a solid state reaction and spark plasma sintering.

scholarly journals Mechanical Milling-Assisted Spark Plasma Sintering of Fine-Grained W-Ni-Mn Alloy

Materials ◽  
2018 ◽  
Vol 11 (8) ◽  
pp. 1323 ◽  
Author(s):  
Yanlin Pan ◽  
Daoping Xiang ◽  
Ning Wang ◽  
Hui Li ◽  
Zhishuai Fan
Keyword(s):  
Spark Plasma Sintering ◽  
Mechanical Milling ◽  
Bending Strength ◽  
Sintering Temperature ◽  
Interface Fracture ◽  
Composite Powders ◽  
Fine Grained ◽  
Plasma Sintering ◽  
Binding Phase ◽  
Spark Plasma

Fine-grained W-6Ni-4Mn alloys were fabricated by spark plasma sintering (SPS) using mechanical milling W, Ni and Mn composite powders. The relative density of W-6Ni-4Mn alloy increases from 71.56% to 99.60% when it is sintered at a low temperature range of 1000–1200 °C for 3 min. The spark plasma sintering process of the alloy can be divided into three stages, which clarify the densification process of powder compacts. As the sintering temperature increases, the average W grain size increases but remains at less than 7 µm and the distribution of the binding phase is uniform. Transmission electron microscopy (TEM) observation reveals that the W-6Ni-4Mn alloy consists of the tungsten phase and the γ-(Ni, Mn, W) binding phase. As the sintering temperature increases, the Rockwell hardness and bending strength of alloys initially increases and then decreases. The optimum comprehensive hardness and bending strength of the alloy are obtained at 1150 °C. The main fracture mode of the alloys is W/W interface fracture.

Sign in / Sign up

Export Citation Format

Share Document