X-Ray Photoelectron Spectroscopy Characterization of Polyaniline-Cellulose Ester Composite Membranes

2010 ◽  
Vol 657 ◽  
pp. 35-45 ◽  
Author(s):  
Asif A. Qaiser ◽  
Margaret M. Hyland
Keyword(s):  
Oxidation State ◽  
Photoelectron Spectroscopy ◽  
Membrane Surface ◽  
Oxidative Polymerization ◽  
Composite Membranes ◽  
Core Level ◽  
Ring Cleavage ◽  
Cellulose Ester ◽  
X Ray

X-ray photoelectron spectroscopy (XPS) is a promising technique employed for the study of conducting polymers and their composites. XPS was used to study the surface chemistry of polyaniline-mixed cellulose ester (PANI-ME) composite membranes prepared by various chemical oxidative polymerization techniques such as insitu solution, vapour phase polymerizations and aniline polymerization using a two-compartment permeation cell. Hydrolytic degradation of surface deposited PANI and scission of cellulosic chains due to x-ray irradiation inside the XPS chamber influenced the quantification of polyaniline deposition levels as well as oxidation and doping states in PANI-ME membranes. N1s core level spectra allowed characterization of the PANI deposition level, its oxidation state and x-ray induced cellulosic ring cleavage. C1s and O1s core level spectra revealed PANI hydrolysis at the membrane surface. These degradation phenomena influence the performance of PANI composite membranes used specifically in electrodiffusion applications. It was shown that successful quantification of PANI deposition levels and its oxidation state on microporous mixed cellulose ester membranes using XPS could be realized by incorporating the degradation effects in the characterization results.

Characterization of Oxidized Nickel (II) Dimethylglyoxime Using X-Ray Photoelectron Spectroscopy

1987 ◽  
Vol 41 (6) ◽  
pp. 994-1000 ◽  
Author(s):  
V. Y. Young ◽  
F. C. Chang ◽  
K. L. Cheng
Keyword(s):  
Oxidation State ◽  
Photoelectron Spectroscopy ◽  
Binding Energies ◽  
Core Level ◽  
Solution Phase ◽  
Intensity Data ◽  
X Ray ◽  
Complex Core

X-ray photoelectron spectroscopy has been used to determine the oxidation state of nickel in the oxidized nickel (II) dimethylglyoxime complex. Core level binding energies for the Ni(2p), N(1s), and O(1s) levels; the presence or absence of shake-up satellites on the Ni(2p) levels; and the analysis of intensity data are consistent only with an assignment of +3. Structures consistent with the data are proposed for both the solid-and the solution-phase complexes.

Preparation and Characterization of Carbon Nanotubes/Al2O3 Inorganic Hybrid Material - A Bio-Inspired Poly(Dopamine) Approach

2018 ◽  
Vol 54 ◽  
pp. 127-135
Author(s):  
Wen Zhao ◽  
Wen Cai Wang ◽  
Yong Lai Lu ◽  
Li Qun Zhang
Keyword(s):  
Carbon Nanotubes ◽  
Aqueous Solution ◽  
Photoelectron Spectroscopy ◽  
Oxidative Polymerization ◽  
The Self ◽  
Liquid Phase Deposition ◽  
X Ray ◽  
Transmission Electron ◽  
Cnts Surface

Carbon nanotubes/alumina (CNTs/Al2O3) nanocomposites were prepared by the poly (dopamine) assisted chemical liquid phase deposition (CLPD). The poly (dopamine) layers were firstly coated on the CNTs surface uniformly by the self-oxidative polymerization of dopamine in mild aqueous solution and then the Al2O3 nanoparticles formed on the poly (dopamine) coated CNTs surface by the CLPD. The hydrophilic poly (dopamine) layers on the CNTs surface can improve the dispersion of CNTs in aqueous solution. Moreover, it can be used as a key linker between the CNTs and Al2O3 because of the nitrogen-containing group in poly (dopamine) could coordinate with Al3+ ions. The as-prepared poly (dopamine) coated CNTs and CNTs/Al2O3 nanohybrids were characterized by X-ray photoelectron spectroscopy (XPS), X-radial diffractometer (XRD) and high resolution transmission electron microscopy (HRTEM). These results showed that the poly (dopamine) layers were coated on the surface of CNTs uniformly, and the Al2O3 nanoparticles embellished with the poly (dopamine) coated CNTs surface. Compared with pristine NR composites, the thermal conductivity of the as-prepared NR/CNTs@Al2O3 composites increased 17%.

Synthesis and characterization of organic–inorganic poly(3,4-ethylenedioxythiophene)/MoS2 nanocomposite via in situ oxidative polymerization

2006 ◽  
Vol 21 (1) ◽  
pp. 112-118 ◽  
Author(s):  
A. Vadivel Murugan ◽  
Mathieu Quintin ◽  
Marie-Helene Delville ◽  
Guy Campet ◽  
Annamraju Kasi Viswanath ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Oxidative Polymerization ◽  
X Ray Diffraction ◽  
Rechargeable Lithium Batteries ◽  
X Ray ◽  
Transmission Electron ◽  
Basal Distance ◽  
New Type

Here we demonstrate the synthesis of a new type of layered poly(3,4-ethylenedioxy- thiophene) (PEDOT)/MoS2 nanocomposite via flocculation of delaminated MoS2 with subsequent in situ oxidative polymerization of 3,4-ethylenedioxythiophene. The resulting nanocomposite was characterized by Fourier transform infrared spectroscopy, powder x-ray diffraction, x-ray photoelectron spectroscopy, thermal analysis, transmission electron microscopy, and four-probe electrical conductivity measurements with respect to temperature. X-ray diffraction results indicated that the exfoliated MoS2 and PEDOT are restacked to produce a novel nanoscale composite material containing alternate nanoribbons of PEDOT in between MoS2 with a basal distance of ∼1.38 nm. The nanocomposite, which could be used as a cathode material for small power rechargeable lithium batteries, has also been demonstrated by the electrochemical insertion of lithium into the PEDOT/MoS2 nanocomposite, where a significant enhancement in the discharge capacity is observed, compared to that of respective pristine molybdenum disulfide.

Surface characterization of di-(2-ethylhexyl)dithiophosphoric acid-activated composite membranes by x-ray photoelectron spectroscopy

2000 ◽  
Vol 30 (1) ◽  
pp. 430-433 ◽  
Author(s):  
Mar�a Jes�s Ariza ◽  
Enrique Rodr�guez-Castell�n ◽  
Rodrigo Rico ◽  
Juana Benavente ◽  
Mar�a Mu�oz ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Surface Characterization ◽  
Composite Membranes ◽  
Dithiophosphoric Acid ◽  
X Ray

The Growth and Characterization of Germanium-Carbon Alloy Thin Films

1992 ◽  
Vol 270 ◽  
Author(s):  
Haojie Yuan ◽  
R. Stanley Williams
Keyword(s):  
Thin Films ◽  
Photoelectron Spectroscopy ◽  
Vacuum Chamber ◽  
Optical Band Gap ◽  
High Vacuum ◽  
Optical Absorption Spectroscopy ◽  
Alloy Thin Film ◽  
New Materials ◽  
X Ray

ABSTRACTThin films of pure germanium-carbon alloys (GexC1−x with x ≈ 0.0, 0.2, 0.4, 0.5, 0.6, 0.8, 1.0) have been grown on Si(100) and A12O3 (0001) substrates by pulsed laser ablation in a high vacuum chamber. The films were analyzed by x-ray θ-2θ diffraction (XRD), x-ray photoelectron spectroscopy (XPS), Auger electron spectroscopy (AES), conductivity measurements and optical absorption spectroscopy. The analyses of these new materials showed that films of all compositions were amorphous, free of contamination and uniform in composition. By changing the film composition, the optical band gap of these semiconducting films was varied from 0.00eV to 0.85eV for x = 0.0 to 1.0 respectively. According to the AES results, the carbon atoms in the Ge-C alloy thin film samples has a bonding configuration that is a mixture of sp2 and sp3 hybridizations.

Monitoring and characterization of creation of geopolymers prepared from fly ash and metakaolin by X-ray photoelectron spectroscopy method

2014 ◽  
Vol 34 (3) ◽  
pp. 841-849 ◽  
Author(s):  
M. Kanuchova ◽  
L. Kozakova ◽  
M. Drabova ◽  
M. Sisol ◽  
A. Estokova ◽  
...  
Keyword(s):  
Fly Ash ◽  
Photoelectron Spectroscopy ◽  
Spectroscopy Method ◽  
X Ray

Characterization of columns grown during KrF laser micromachining of Al2O3–TiC ceramics

2003 ◽  
Vol 18 (5) ◽  
pp. 1123-1130 ◽  
Author(s):  
V. Oliveira ◽  
R. Vilar
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Laser Pulses ◽  
Formation Mechanisms ◽  
X Ray ◽  
Reducing Conditions ◽  
Transmission Electron ◽  
Column Formation ◽  
Krf Laser

This paper aims to contribute to the understanding of column formation mechanisms in Al2O3–TiC ceramics micromachined using excimer lasers. Chemical and structural characterization of columns grown in Al2O3–TiC composite processed with 200 KrF laser pulses at 10 J/cm2 was carried out by scanning electron microscopy, transmission electron microscopy, x-ray photoelectron spectroscopy, and x-ray diffraction analysis. Fully developed columns consist of a core of unprocessed material surrounded by an outer layer of Al2TiO5, formed in oxidizing conditions, and an inner layer, formed in reducing conditions, composed of TiC and Al3Ti or an AlTi solid solution. Possible mechanisms of column formation are discussed.

Preparation of Carbon Nanofibers from Polyacrylonitrile Nanofibers by Electrospinning

2011 ◽  
Vol 415-417 ◽  
pp. 642-647
Author(s):  
En Zhong Li ◽  
Da Xiang Yang ◽  
Wei Ling Guo ◽  
Hai Dou Wang ◽  
Bin Shi Xu
Keyword(s):  
Electron Microscope ◽  
Carbon Nanofibers ◽  
Photoelectron Spectroscopy ◽  
Solution Concentration ◽  
Dimethyl Formamide ◽  
Ultrafine Fibers ◽  
X Ray ◽  
Scanning Electron ◽  
Pan Fibers

Ultrafine fibers were electrospun from polyacrylonitrile (PAN)/N,N-dimethyl formamide (DMF) solution as a precursor of carbon nanofibers. The effects of solution concentration, applied voltage and flow rate on preparation and morphologies of electrospun PAN fibers were investigated. Morphologies of the green fibers, stabilized fibers and carbonized fibers were compared by scanning electron microscope (SEM). The diameter of PAN nanofibers is about 450nm and the distribution of diameter is well-proportioned. Characterization of the elements changes of fibers were performed by X-ray photoelectron spectroscopy (XPS).

Sign in / Sign up

Export Citation Format

Share Document