The Role of the Technological Residual Stress in Spiral Bevel Gears’ Degradation

2017 ◽  
Vol 885 ◽  
pp. 153-158
Author(s):  
Dávid Angel ◽  
Márton Benke ◽  
Valéria Mertinger
Keyword(s):  
Residual Stress ◽  
X Ray Diffraction ◽  
Spiral Bevel Gears ◽  
Bevel Gears ◽  
Hardness Tests ◽  
Stress Asymmetry ◽  
Head Segment ◽  
Spiral Bevel ◽  
Microstructure Measurements

The subjects of the examination were automotive components, spiral bevel gears, built up by two main parts, the axle, where the component is prone to fracture, and the head segment, where the working surface can be found. The occasional fracture occurs during the straightening process after the hardening heat treatment. Our aims were to monitor the evolution of the residual stress during the manufacturing processes and to reveal the role of the residual stress in the component’s fracture. The residual stress measurements were carried out via non-destructive X-ray diffraction. To reveal the component’s fracture hardness tests and microstructure measurements were also performed. Based on the results, the fracture of the components were connected to the stress asymmetry which was derived from the microstructure of the early stages of manufacturing.

scholarly journals Contact stiffness and damping of spiral bevel gears under transient mixed lubrication conditions

Friction ◽  
2021 ◽  
Author(s):  
Zongzheng Wang ◽  
Wei Pu ◽  
Xin Pei ◽  
Wei Cao
Keyword(s):  
Contact Stiffness ◽  
Mixed Lubrication ◽  
Asperity Contact ◽  
Spiral Bevel Gears ◽  
Bevel Gears ◽  
Dry Contact ◽  
Spiral Bevel ◽  
Stiffness And Damping ◽  
Lubrication Conditions ◽  
Film Lubrication

AbstractExisting studies primarily focus on stiffness and damping under full-film lubrication or dry contact conditions. However, most lubricated transmission components operate in the mixed lubrication region, indicating that both the asperity contact and film lubrication exist on the rubbing surfaces. Herein, a novel method is proposed to evaluate the time-varying contact stiffness and damping of spiral bevel gears under transient mixed lubrication conditions. This method is sufficiently robust for addressing any mixed lubrication state regardless of the severity of the asperity contact. Based on this method, the transient mixed contact stiffness and damping of spiral bevel gears are investigated systematically. The results show a significant difference between the transient mixed contact stiffness and damping and the results from Hertz (dry) contact. In addition, the roughness significantly changes the contact stiffness and damping, indicating the importance of film lubrication and asperity contact. The transient mixed contact stiffness and damping change significantly along the meshing path from an engaging-in to an engaging-out point, and both of them are affected by the applied torque and rotational speed. In addition, the middle contact path is recommended because of its comprehensive high stiffness and damping, which maintained the stability of spiral bevel gear transmission.

Deformations and Stresses in Face-Hobbed Spiral Bevel Gears

2011 ◽  
Author(s):  
Vilmos V. Simon
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Nodal Point ◽  
Design Parameters ◽  
Element Discretization ◽  
Spiral Bevel Gears ◽  
Bevel Gears ◽  
Tooth Surfaces ◽  
Spiral Bevel ◽  
Element Method

In this study an attempt is made to predict displacements and stresses in face-hobbed spiral bevel gears by using the finite element method. A displacement type finite element method is applied with curved, 20-node isoparametric elements. A method is developed for the automatic finite element discretization of the pinion and the gear. The full theory of the generation of tooth surfaces of face-hobbed spiral bevel gears is applied to determine the nodal point coordinates on tooth surfaces. The boundary conditions for the pinion and the gear are set automatically as well. A computer program was developed to implement the formulation provided above. By using this program the influence of design parameters and load position on tooth deflections and fillet stresses is investigated. On the basis of the results, obtained by performing a big number of computer runs, by using regression analysis and interpolation functions, equations for the calculation of tooth deflections and fillet stresses are derived.

scholarly journals Lubrication characteristics of gear after shot peening base on 25-pellet model

2018 ◽  
Vol 10 (7) ◽  
pp. 168781401879065 ◽  
Author(s):  
Shuai Mo ◽  
Shengping Zhu ◽  
Guoguang Jin ◽  
Jiabei Gong ◽  
Zhanyong Feng ◽  
...  
Keyword(s):  
Shot Peening ◽  
High Speed ◽  
Target Material ◽  
Bevel Gear ◽  
Tooth Surface ◽  
Spiral Bevel Gear ◽  
Spiral Bevel Gears ◽  
Bevel Gears ◽  
Spiral Bevel ◽  
Lubrication Characteristics

High-speed heavy-load spiral bevel gears put forward high requirement for flexural strength; shot peening is a technique that greatly improves the bending fatigue strength of gears. During shot peening, a large number of fine pellets bombard the surface of the metal target material at very high speeds and let the target material undergo plastic deformation, at the same time strengthening layer is produced. Spiral bevel gear as the object of being bombarded inevitably brought the tooth surface micro-morphology changes. In this article, we aim to reveal the effect of microtopography of tooth shot peening on gear lubrication in spiral bevel gear, try to establish a reasonable description of the microscopic morphology for tooth surface by shot peening, to reveal the lubrication characteristics of spiral bevel gears after shot peening treatment based on the lubrication theory, and do comparative research on the surface lubrication characteristics of a variety of microstructures.

scholarly journals A Method for Thermal Analysis of Spiral Bevel Gears

1996 ◽  
Vol 118 (4) ◽  
pp. 580-585 ◽  
Author(s):  
R. F. Handschuh ◽  
T. P. Kicher
Keyword(s):  
Three Dimensional ◽  
Contact Analysis ◽  
Heat Transfer Analysis ◽  
Maximum Pressure ◽  
Tooth Contact Analysis ◽  
Tooth Contact ◽  
Finite Element Program ◽  
Spiral Bevel Gears ◽  
Bevel Gears ◽  
Spiral Bevel

A modelling method for analyzing the three-dimensional thermal behavior of spiral bevel gears has been developed. The model surfaces are generated through application of differential geometry to the manufacturing process for face-milled spiral bevel gears. Contact on the gear surface is found by combining tooth contact analysis with three-dimensional Hertzian theory. The tooth contact analysis provides the principle curvatures and orientations of the two surfaces. This information is then used directly in the Hertzian analysis to find the contact size and maximum pressure. Heat generation during meshing is determined as a function of the applied load, sliding velocity, and coefficient of friction. Each of these factors change as the point of contact changes during meshing. A nonlinear finite element program was used to conduct the heat transfer analysis. This program permitted the time- and position-varying boundary conditions, found in operation, to be applied to a one-tooth model. An example model and analytical results are presented.

Sign in / Sign up

Export Citation Format

Share Document