Research of Heat Input in Friction Stir Welding

2019 ◽  
Vol 945 ◽  
pp. 634-638
Author(s):  
V. Statsenko ◽  
A. Sukhorada ◽  
M. Bernvskaya
Keyword(s):  
Friction Stir Welding ◽  
Heat Input ◽  
Rotation Speed ◽  
Heat Losses ◽  
High Tech ◽  
Heat Power ◽  
Friction Stir ◽  
Experimental Scheme ◽  
Experimental Tube ◽  
Productive Process

Nowadays the most perspective, high-tech and productive process is friction stir welding. The most important part of this technology is to determine the temperature of the material in the stir zone. This parameter is easily counted by the amount of the heat input, put in the welding zone. We made experimental researches about the relation of the heat input, therotation speed and thediameter of the working tool. For that purpose an experimental scheme was chosen, which models a welding material (aluminum alloy AMg5) as an experimental tube 20 mm in diameter. The tool (shear steel P6M5) is modeled as a working plate. Measurements of the frictional moments depending on the rotation speed of the experimental working tube during the constant temperature are made on the prepared stand. By the experimental data the specific heat input and the heat power were counted on every concentric ring, 2 mm in width, in the end of the working tool, 20 mm in diameter. Also, the sum of the heat power for the whole tool during various rotation speed terms was counted too. On the stand throughout the experiment were determined all the thermal conductivity heat losses along the rod, which the experimental tube was pinned on, all the working plate heat losses through the gasket towards the working desk and the convection from the surface of the rotating experimental tube to the environment. According the data, any of these losses is from 3 to 10 percent. This is shown in the heat input counting.

Research of Heat Power in Friction Stir Spot Welding

2019 ◽  
Vol 806 ◽  
pp. 81-86
Author(s):  
V. Statsenko ◽  
A. Sukhorada
Keyword(s):  
Heat Input ◽  
Spot Welding ◽  
Rotation Speed ◽  
Friction Stir Spot Welding ◽  
Heat Losses ◽  
High Tech ◽  
Heat Power ◽  
Friction Stir ◽  
Experimental Scheme ◽  
Experimental Tube

Nowadays the most perspective, high-tech and productive process is friction stir spot welding. The most important part of this technology is to determine the temperature of the material in the stir zone. This parameter is easily counted by the amount of the heat input, put in the welding zone. We made experimental researches about the relation of the heat power, therotation speed and the diameter of the working tool. For that purpose an experimental scheme was chosen, which models a welding material (aluminum alloy AMg5) as an experimental tube 20 mm in diameter. The tool (shear steel P6M5) is modeled as a working plate. Measurements of the frictional moments depending on the rotation speed of the experimental working tube during the constant temperature are made on the prepared stand. By the experimental data the specific heat input and the heat power were counted on every concentric ring, 2 mm in width, in the end of the working tool, 20 mm in diameter. Also, the sum of the heat power for the whole tool during various rotation speed terms was counted too. On the stand throughout the experiment were determined all the thermal conductivity heat losses along the rod, which the experimental tube was pinned on, all the working plate heat losses through the gasket towards the working desk and the convection from the surface of the rotating experimental tube to the environment. According the data, any of these losses is from 3 to 10 percent. This is shown in the heat input counting.

Methodology for Calculating Heat Loss in the Study of Friction Stir Welding

2021 ◽  
Vol 887 ◽  
pp. 575-580
Author(s):  
V. Statsenko ◽  
A. Sukhorada ◽  
N. Mikhailova
Keyword(s):  
Friction Stir Welding ◽  
Tool Steel ◽  
Heat Input ◽  
Heat Liberation ◽  
High Tech ◽  
Steel R6m5 ◽  
Heat Power ◽  
Friction Stir ◽  
Experimental Tube ◽  
Productive Process

Currently, the most promising high-tech and productive process is friction stir welding. An important element of this technology is the determination of the material temperature in the stir zone, which can be determined by calculation based on the amount of heat input introduced into the welding zone. To determine this value, experimental of the dependence of heat input on the tool rotation speed and welding speed were carried out. For this, a scheme of experiments has been selected in which the material to be welded (aluminum alloy AMg5) is modeled as an experimental tube with a diameter of 20 mm, and the tool (made of tool steel R6M5) is modeled as a working plate. On the designed and manufactured stand, studies of the dependence of the heat-liberation value for the speeds of rotation of the experimental tube 42-105 rad/s were carried out. In this case, due to the pressing force of the experimental tube and the working plate, a constant temperature of the place of friction was maintained. The obtained experimental data were used to calculate the heat-liberation value and heat power on each concentric ring 2 mm wide at the end of the working tool with a diameter of 20 mm, as well as the total heat power for different speeds of rotation and welding.When carrying out experiments on the bench, heat losses were determined by thermal conductivity along the rod on which the experimental tube is fixed, as well as from the working plate made of tool steel through the gasket onto the working table and by convection from the surface of the rotating experimental tube into the environment. The calculation results showed that each of these losses does not exceed 3-10%. These losses are taken into account in the heat supply calculations.

Microstructure and Mechanical Properties of Friction Stir Welded Annealed Pure Copper Joints

2013 ◽  
Vol 787 ◽  
pp. 346-351
Author(s):  
Salar Salahi ◽  
Vahid Rezazadeh ◽  
Atabak Iranizad ◽  
Ali Hosseinzadeh ◽  
Amir Safari
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Welding Speed ◽  
Heat Input ◽  
Applied Load ◽  
Rotation Speed ◽  
Pure Copper ◽  
Friction Stir ◽  
Tool Rotation Speed ◽  
Tool Rotation

As a novel technique for joining materials, friction stir welding (FSW) has significant advantages over the conventional welding methods and is widely applied for joining different materials including aluminum, magnesium and copper alloys. In this research, the mechanical and microstructural characteristics of friction stir welded annealed pure copper joints were investigated. The influence of the tool rotation speed, welding speed and applied load was studied. The friction stir welding (FSW) was conducted at welding speed ranged from 30 to 70 mm/ min, rotation speed ranged from 400 to 1200rpm and applied load ranged from 1000 to 1500 kg. After welding process, tensile and Vickers hardness tests were performed. It has been found that increasing the tool rotational speed and/or reducing the welding speed increases heat input and causes grain coarsening in stir zone. High applied load refines the microstructure of NZ and increases the hardness and tensile strength of NZ. An optimum heat input condition was found to reach the best mechanical properties of the joints. The tensile characteristics of the friction stir welded tensile samples depend significantly on the tool rotation speed ,welding speed and applied load.

scholarly journals Dissimilar Friction Stir Welding of AA2024 and AISI 1018: Microstructure and Mechanical Properties

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 330
Author(s):  
Mohamed M. Z. Ahmed ◽  
Nabil Jouini ◽  
Bandar Alzahrani ◽  
Mohamed M. El-Sayed Seleman ◽  
Mohammad Jhaheen
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Friction Stir Welding ◽  
Cross Section ◽  
Heat Input ◽  
Rotation Rate ◽  
Rotation Speed ◽  
Transverse Cross Section ◽  
Traverse Speed ◽  
Friction Stir

This study investigated the effect of the friction stir welding rotation rate and welding speed on the quality and properties of the dissimilar joints between aluminum and carbon steel. Plates of 4 mm thickness from both AA2024 and AISI 1018 were successfully friction stir butt welded at rotation speeds of 200, 250, and 300 rpm and welding speeds of 25, 50, and 75 mm/min. The joint quality was investigated along the top surface and the transverse cross-sections. Further investigation using scanning electron microscopy was conducted to assess the intermetallic layers and the grain refining in the stir zone. The mechanical properties were investigated using tensile testing for two samples for each weld that wire cut perpendicular to the welding direction and the hardness profiles were obtained along the transverse cross-section. Both the top surface and the transverse cross-section macrographs indicated defect free joints at a rotation rate of 250 rpm with the different welding speeds. The intermetallic compounds (IMCs) formation was significantly affected by the heat input, where there is no formation of IMCs at the Al/steel interfaces when higher traverse speed (75 mm/min) or lower rotation speed (200 rpm) were used, which gave the maximum tensile strength of about 230 MPa at the low rotation speed (200 rpm) along with 3.2% elongation. This is attributed to the low amount of heat input (22.32 J/mm) experienced. At the low traverse speed (25 mm/min and 250 rpm), a continuous layer of Al-rich IMCs FeAl3 is formed at the joint interface due to the high heat input experienced (79.5 J/mm). The formation of the IMCs facilitates fracture and reduced the tensile strength of the joint to about 98 MPa. The fracture mechanism was found to be of mixed mode and characterized by a cleavage pattern and dimples. The hardness profiles indicated a reduction in the hardness at the aluminum side and an increase at the steel side.

scholarly journals Effect of Stirring Pin Rotation Speed on Microstructure and Mechanical Properties of 2A14-T4 Alloy T-Joints Produced by Stationary Shoulder Friction Stir Welding

Materials ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 1938
Author(s):  
Haifeng Yang ◽  
Hongyun Zhao ◽  
Xinxin Xu ◽  
Li Zhou ◽  
Huihui Zhao ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Rotation Speed ◽  
Weld Nugget ◽  
Al Alloy ◽  
Nugget Zone ◽  
T Joints ◽  
Friction Stir ◽  
Stationary Shoulder ◽  
Microstructure And Mechanical Properties

In this study, 2A14-T4 Al-alloy T-joints were prepared via stationary shoulder friction stir welding (SSFSW) technology where the stirring pin’s rotation speed was set as different values. In combination with the numerical simulation results, the macro-forming, microstructure, and mechanical properties of the joints under different welding conditions were analyzed. The results show that the thermal cycle curves in the SSFSW process are featured by a steep climb and slow decreasing variation trends. As the stirring pin’s rotation speed increased, the grooves on the weld surface became more obvious. The base and rib plates exhibit W- or N-shaped hardness distribution patterns. The hardness of the weld nugget zone (WNZ) was high but was lower than that of the base material. The second weld’s annealing effect contributed to the precipitation and coarsening of the precipitated phase in the first weld nugget zone (WNZ1). The hardness of the heat affect zone (HAZ) in the vicinity of the thermo-mechanically affected zone (TMAZ) dropped to the minimum. As the stirring pin's rotation speed increased, the tensile strengths of the base and rib plates first increased and then dropped. The base and rib plates exhibited ductile and brittle/ductile fracture patterns, respectively.

Features of structure formation processes in AA2024 alloy joints formed by the friction stir welding with bobbin tool

2021 ◽  
Vol 23 (2) ◽  
pp. 98-115
Author(s):  
Alexey Ivanov ◽  
◽  
Valery Rubtsov ◽  
Andrey Chumaevskii ◽  
Kseniya Osipovich ◽  
...  
Keyword(s):  
Friction Stir Welding ◽  
Structure Formation ◽  
Welded Joints ◽  
Heat Input ◽  
Welded Joint ◽  
Welding Process ◽  
Tool Material ◽  
Travel Speed ◽  
Material System ◽  
Friction Stir

Introduction. One of friction stir welding types is the bobbin friction stir welding (BFSW) process, which allows to obtain welded joints in various configurations without using a substrate and axial embedding force, as well as to reduce heat loss and temperature gradient across the welded material thickness. This makes the BFSW process effective for welding aluminum alloys, which properties are determined by their structural-phase state. According to research data, the temperature and strain rate of the welded material have some value intervals in which strong defect-free joints are formed. At the same time, much less attention has been paid to the mechanisms of structure formation in the BFSW process. Therefore, to solve the problem of obtaining defect-free and strong welded joints by BFSW, an extended understanding of the basic mechanisms of structure formation in the welding process is required. The aim of this work is to research the mechanisms of structure formation in welded joint of AA2024 alloy obtained by bobbin tool friction stir welding with variation of the welding speed. Results and discussion. Weld formation conditions during BFSW process are determined by heat input into a welded material, its fragmentation and plastic flow around the welding tool, which depend on the ratio of tool rotation speed and tool travel speed. Mechanisms of joint formation are based on a combination of equally important processes of adhesive interaction in “tool-material” system and extrusion of metal into the region behind the welding tool. Combined with heat dissipation conditions and the configuration of the “tool-material” system, this leads to material extrusion from a welded joint and its decompaction. This results in formation of extended defects. Increasing in tool travel speed reduce the specific heat input, but in case of extended joints welding an amount of heat released in joint increases because of specific heat removal conditions. As a result, the conditions of adhesion interaction and extrusion processes change, which leads either to the growth of existing defects or to the formation of new ones. Taking into account the complexity of mechanisms of structure formation in joint obtained by BFSW, an obtaining of defect-free joints implies a necessary usage of various nondestructive testing methods in combination with an adaptive control of technological parameters directly in course of a welding process.

scholarly journals PENGARUH TOOL ROTATION SPEED TERHADAP SIFAT MEKANIK SAMBUNGAN ALUMINIUM PADUAN 6061-T6 PADA PROSES FRICTION STIR WELDING

2019 ◽  
Vol 25 (3) ◽  
Author(s):  
Tarmizi Tarmizi ◽  
Riki Indrawan ◽  
Irfan Irfan
Keyword(s):  
Friction Stir Welding ◽  
Rotation Speed ◽  
Friction Stir ◽  
Tool Rotation Speed ◽  
Tool Rotation

PENGARUH TOOL ROTATION SPEED TERHADAP SIFAT MEKANIK SAMBUNGAN ALUMINIUM PADUAN 6061 T6 PADA PROSES FRICTION STIR WELDING. Pengelasan aduk tekan merupakan proses pengelasan yang baru dikembangkan pada tahun 1991, hingga saat ini berbagai penelitian terus dilakukan untuk menemukan parameter yang dapat menghasilkan sambungan las yang optimum sebagai alternatif proses pengelasan fusi yang masih memiliki beberapa kekurangan. Penelitian ini bertujuan untuk mengetahui pengaruh kecepatan putar tool yang menjadi salah satu parameter penting dalam friction stir welding pada pelat aluminium paduan 6061-T6 dengan tebal 6 mm terhadap sifat mekanik sambungan las, dengan variasi kecepatan putar yang digunakan 910 rpm, 1175 rpm, 1555 rpm, 1700 rpm dan 2000 rpm untuk mendapatkan parameter yang optimum. Berdasarkan penelitian yang telah dilakukan didapatkan hasil bahwa sambungan las dengan kecepatan putaran 910 rpm, 1175 rpm dan 1555 rpm tidak terdapat cacat dan memenuhi kriteria sambungan las berdasarkan standar AWS D17.3 sedangkan sambungan las yang memiliki sifat mekanik yang paling optimum yaitu sambungan las dengan kecepatan putar tool 910 rpm karena pengkasaran butir dan larutnya presipitat tidak terlalu signifikan dibandingkan dengan kecepatan putaran lainnya.Kata kunci: Pengelasan aduk tekan, pengelasan fusi, kecepatan putar, tool, aluminium paduan 6061-T6.

A Study on Friction Stir Welding Process for AA2219/AA2195 Joints

2018 ◽  
Vol 762 ◽  
pp. 339-342
Author(s):  
Ho Sung Lee ◽  
Koo Kil No ◽  
Joon Tae Yoo ◽  
Jong Hoon Yoon
Keyword(s):  
Friction Stir Welding ◽  
Welded Joints ◽  
Rotation Speed ◽  
Microstructural Analysis ◽  
Frictional Heat ◽  
Welding Parameters ◽  
Manufacturing Cost ◽  
Significant Saving ◽  
Friction Stir ◽  
Rotation Direction

The object of this study was to study mechanical properties of friction stir welded joints of AA2219 and AA2195. AA2219 has been used as an aerospace materials for many years primarily due to its high weldability and high specific strength in addition to the excellent cryogenic property so to be successfully used for manufacturing of cryogenic fuel tank for space launcher. Relatively new Aluminum-Lithium alloy, AA2195 provides significant saving on weight and manufacturing cost with application of friction stir welding. Friction stir welding is a solid-state joining process, which use a spinning tool to produce frictional heat in the work piece. To investigate the effect of the rotation direction of the tool, the joining was performed by switching the positions of the two dissimilar alloys. The welding parameters include the travelling speed, rotation speed and rotation direction of the tool, and the experiment was conducted under the condition that the travelling speed of the tool was 120-300 mm/min and the rotation speed of the tool was 400-800 rpm. Tensile tests were conducted to study the strength of friction stir welded joints and microhardness were measured with microstructural analysis. The results indicate the failure occurred in the relatively weaker TMAZ/HAZ interface of AA2219. The optimum process condition was obtained at the rotation speed of 600-800 rpm and the travelling speed of 180-240 mm/min.

scholarly journals Material Flow Visualization of Dissimilar Friction STIR Welding Process Using Nano-Computed Tomography

2018 ◽  
Vol 140 (11) ◽  
Author(s):  
Xun Liu ◽  
Sheng Zhao ◽  
Kai Chen ◽  
Jun Ni
Keyword(s):  
Computed Tomography ◽  
Friction Stir Welding ◽  
Heat Input ◽  
Material Flow ◽  
Volume Fraction ◽  
Weld Zone ◽  
Process Conditions ◽  
Rotating Speed ◽  
Friction Stir ◽  
Small Tool

In this study, the friction stir welding (FSW) of aluminum alloy 6061-T6511 to TRIP 780 steel is analyzed under various process conditions. Two FSW tools with different sizes are used. To understand the underlying joining mechanisms and material flow behavior, nano-computed tomography (nano-CT) is applied for a 3D visualization of material distribution in the weld. With insufficient heat input, steel fragments are generally scattered in the weld zone in large pieces. This is observed in a combined condition of big tool, small tool offset, and low rotating speed or a small tool with low rotating speed. Higher heat input improves the material flowability and generates a continuous strip of steel. The remaining steel fragments are much finer. When the volume fraction of steel involved in the stirring nugget is small, this steel strip can be in a flat shape near the bottom, which generally corresponds to a better joint quality and the joint would fracture in the base aluminum side. Otherwise, a hook structure is formed and reduces the joint strength. The joint would fail with a combined brittle behavior on the steel hook and a ductile behavior in the surrounding aluminum matrix.

Sign in / Sign up

Export Citation Format

Share Document