Numerical Simulation on Effects of TCO Work Function on Performance of a-Si:H Solar Cells

2019 ◽  
Vol 966 ◽  
pp. 501-506
Author(s):  
Ahmad Sholih ◽  
Dadan Hamdani ◽  
Sigit Tri Wicaksono ◽  
Mas Irfan P. Hidayat ◽  
Yoyok Cahyono ◽  
...  
Keyword(s):  
Solar Cells ◽  
Work Function ◽  
Conversion Efficiency ◽  
High Efficiency ◽  
Low Cost ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Conducting Oxides ◽  
Conversion Efficiencies

In this paper, we have investigated the effect of the work function of transparent conducting oxides (TCO) on the performance of a-Si:H p-i-n solar cells, including open circuit voltage (VOC), short circuit current (JSC), fill factor (FF) and conversion efficiency, using AFORS-HET software. The simulation has focused on two layers: front contact work function (ΦTCO-front) and back contact work function (ΦTCO-back) with various band from 4.7 eV to 5.3 eV and 4.2 eV to 4.9 eV respectively. From the simulation results, we know that the work function of TCO greatly affects the performance of solar cells such as Voc, Jsc, FF and conversion efficiency. By optimization, we arrive at results for Voc, Jsc, FF and conversion efficiencies of 0.88 V, 8.95 mA / cm2, 65% and 5.1% respectively. This result is obtained on ΦTCO-front 5.2 eV. When ΦTCO-front 5.2 eV, the value of VOC, FF and conversion efficiency has been saturated, while the value of the J sc actually begins to decrease. Furthermore, when the ΦTCO - back is 4.3 eV, we get the best results for VOC, Jsc, FF and conversion Efficiency of 0.9 V, 8.96 mA / cm2, 73 % and 5.9 % respectively. When ΦTCO-back 4.3 eV, the value of VOC, FF and conversion efficiency begins to decrease, while the value of the Jsc does’t change significantly. These optimizations may help in producing low cost high efficiency p-i-n solar cells experimentally.

scholarly journals Optimization of Rear Local Al-Contacts on High Efficiency Commercial PERC Solar Cells with Dot and Line Openings

2014 ◽  
Vol 2014 ◽  
pp. 1-5 ◽  
Author(s):  
Peisheng Liu ◽  
Xiaolong Zhang ◽  
Ling Sun ◽  
Shanshan Dai ◽  
Chenhui Yu ◽  
...  
Keyword(s):  
Conversion Efficiency ◽  
High Efficiency ◽  
Crystalline Silicon ◽  
Short Circuit ◽  
Rear Surface ◽  
Short Circuit Current ◽  
Alloy Layer ◽  
Open Circuit ◽  
Carrier Lifetimes ◽  
Conversion Efficiencies

Crystalline silicon PERCs with dot or line openings on rear surface were studied here. By measuring the minor carrier lifetimes of the PERCs with dot and line openings, passivation effects of rear surface with dot and line openings were discussed. The performance affected by dot and line openings was analyzed in detail by testing the open-circuit voltages, short-circuit current densities, fill factors, and conversion efficiencies of the PERCs. The results show that the wider space resulted in better minor carrier lifetimes on the rear surface. And the cells with a line opening space of 0.5 mm had an average of 0.22% improvement of conversion efficiency, compared with the cells with full-area Al-BSF. On the other hand, the dot opening PERCs exhibited only a conversion efficiency of 17.4%, although there had been good rear surface reflectivity. The bad Al-Si alloy layer and large hollow densities in dot Al-contacts resulted in bad performance of the PERCs with dot openings.

scholarly journals ABX3 inorganic halide perovskites for solar cells: chemical and crystal structure stability

2021 ◽  
Vol 26 (4) ◽  
Author(s):  
Cristian Moisés Díaz-Acosta ◽  
Antonia Martínez-Luévanos ◽  
Sofía Estrada-Flores ◽  
Lucia Fabiola Cano-Salazar ◽  
Elsa Nadia Aguilera-González ◽  
...  
Keyword(s):  
Crystal Structure ◽  
Solar Cells ◽  
High Efficiency ◽  
Low Cost ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Structure Stability ◽  
Halide Perovskites ◽  
Halide Perovskite

ABSTRACT Solar energy is one of the most promising and developed technologies in recent years, due to its high efficiency and low cost. Perovskite-type solar cells have been the focus of attention by the world scientific community. The main objective of this article is to present an (PSCs) analysis of the various investigations reported on the development of ABX3 inorganic halide perovskite-based solar cells, with emphasis in the effect that temperature and humidity have on their chemical and crystal structure stability. The main methods that are used to obtain ABX3 inorganic halide perovskites are also presented and analyzed. An analysis about the structure of these photovoltaic cells and how to improve their efficiency (PCS), fill factor (FF), short circuit current density (Jsc) and open circuit voltage (Voc) of these devices is presented. As a conclusion, a relationship of the methods, synthesis variables, and type of inorganic halide perovskite used for the development of devices with the best efficiencies is presented; the trends towards which this area of science is heading are also highlighted.

Simulation of InAIN/Si Single-Heterojunction Solar Cells Using wxAMPS

2014 ◽  
Vol 665 ◽  
pp. 111-114 ◽  
Author(s):  
Ying Huang ◽  
Xiao Ming Shen ◽  
Xiao Feng Wei
Keyword(s):  
Solar Cells ◽  
Fill Factor ◽  
High Efficiency ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Indium Content ◽  
Open Circuit ◽  
Heterojunction Solar Cells ◽  
Si Solar Cells

In this paper, InAlN/Si single-heterojunction solar cells have been theoretically simulated based on wxAMPS software. The photovoltaic parameters, such as open circuit voltage, short circuit current, fill factor and conversion efficiency were investigated with changing the indium content and thickness of n-InAlN layer. Simulation results show that the optimum efficiency of InAlN/Si solar cells is 23.1% under AM 1.5G spectral illuminations, with the indium content and thickness of n-InAlN layer are 0.65 and 600nm, respectively. The simulation would contribute to design and fabricate high efficiency InAlN/Si solar cells in experiment.

scholarly journals Investigation of Low-Cost Surface Processing Techniques for Large-Size Multicrystalline Silicon Solar Cells

2010 ◽  
Vol 2010 ◽  
pp. 1-6 ◽  
Author(s):  
Yuang-Tung Cheng ◽  
Jyh-Jier Ho ◽  
William J. Lee ◽  
Song-Yeu Tsai ◽  
Yung-An Lu ◽  
...  
Keyword(s):  
Solar Cells ◽  
Silicon Nitride ◽  
Conversion Efficiency ◽  
High Efficiency ◽  
Short Circuit ◽  
Open Circuit ◽  
Multicrystalline Silicon ◽  
Double Layers ◽  
Large Size ◽  
Si Solar Cells

The subject of the present work is to develop a simple and effective method of enhancing conversion efficiency in large-size solar cells using multicrystalline silicon (mc-Si) wafer. In this work, industrial-type mc-Si solar cells with area of125×125 mm2were acid etched to produce simultaneouslyPOCl3emitters and silicon nitride deposition by plasma-enhanced chemical vapor deposited (PECVD). The study of surface morphology and reflectivity of different mc-Si etched surfaces has also been discussed in this research. Using our optimal acid etching solution ratio, we are able to fabricate mc-Si solar cells of 16.34% conversion efficiency with double layers silicon nitride (Si3N4) coating. From our experiment, we find that depositing double layers silicon nitride coating on mc-Si solar cells can get the optimal performance parameters. Open circuit (Voc) is 616 mV, short circuit current (Jsc) is 34.1 mA/cm2, and minority carrier diffusion length is 474.16 μm. The isotropic texturing and silicon nitride layers coating approach contribute to lowering cost and achieving high efficiency in mass production.

High-Efficiency HIT Solar Cells for Excellent Power Generating Properties

2008 ◽  
Vol 1123 ◽  
Author(s):  
Toshihiro Kinoshita ◽  
Daisuke Ide ◽  
Yasufumi Tsunomura ◽  
Shigeharu Taira ◽  
Toshiaki Baba ◽  
...  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Conversion Efficiency ◽  
Production Cost ◽  
High Efficiency ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Open Circuit ◽  
Surface Recombination Velocity ◽  
Dominant Factor

AbstractIn order to achieve the widespread use of HIT (Hetero-junction with I etero-Intrinsic T ntrinsic Thin-layer) solar cells, it is important to reduce the power generating cost. There are three main approaches for reducing this cost: raising the conversion efficiency of the HIT cell, using a thinner wafer to reduce the wafer cost, and raising the open circuit voltage to obtain a better temperature coefficient. With the first approach, we have achieved the highest conversion efficiency values of 22.3%, confirmed by AIST, in a HIT solar cell. This cell has an open circuit voltage of 0.725 V, a short circuit current density of 38.9 mA/cm2 and a fill factor of 0.791, with a cell size of 100.5 cm2. The second approach is to use thinner Si wafers. The shortage of Si feedstock and the strong requirement of a lower sales price make it necessary for solar cell manufacturers to reduce their production cost. The wafer cost is an especially dominant factor in the production cost. In order to provide low-priced, high-quality solar cells, we are trying to use thinner wafers. We obtained a conversion efficiency of 21.4% (measured by Sanyo) for a HIT solar cell with a thickness of 85μm. Even better, there was absolutely no sagging in our HIT solar cell because of its symmetrical structure. The third approach is to raise the open circuit voltage. We obtained a remarkably higher Voc of 0.739 V with the thinner cell mentioned above because of its low surface recombination velocity. The high Voc results in good temperature properties, which allow it to generate a large amount of electricity at high temperatures.

Effect of CdTe thickness reduction in high efficiency CdS/CdTe solar cells

2001 ◽  
Vol 668 ◽  
Author(s):  
Akhlesh Gupta ◽  
I. Matulionis ◽  
J. Drayton ◽  
A.D. Compaan
Keyword(s):  
Solar Cells ◽  
High Efficiency ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Cdte Film ◽  
Open Circuit ◽  
Thickness Reduction ◽  
X Ray Diffraction ◽  
Cell Parameters ◽  
Cdte Solar Cells

ABSTRACTHigh efficiency CdTe solar cells are typically grown with CdTe thicknesses from 3 to 15 μm, although the thickness required for 90% absorption of the incident irradiation at 800 nm is only ∼1 μm. In this paper, we present the effect of CdTe thickness reduction on the performance of CdS/CdTe solar cells in which both the CdS and CdTe films were grown by sputtering. We produced a series of cells with different CdTe thickness (from 0.5 to 3.0 μm), and held the CdS thickness and back-contact-processing constant. The effect of CdTe thickness reduction on the diffusion of CdS into CdTe was studied using optical absorption and x-ray diffraction techniques. Only slight decreases occur in open-circuit voltage, short-circuit current, and fill factor with decrease in CdTe film thickness to 1.0 μm. Almost 10% efficient cells were obtained with 1 μm CdTe. Below 1 μm, all cell parameters decrease more rapidly, including the red quantum efficiency.

scholarly journals Graded Carrier Concentration Absorber Profile for High Efficiency CIGS Solar Cells

2015 ◽  
Vol 2015 ◽  
pp. 1-9 ◽  
Author(s):  
Antonino Parisi ◽  
Riccardo Pernice ◽  
Vincenzo Rocca ◽  
Luciano Curcio ◽  
Salvatore Stivala ◽  
...  
Keyword(s):  
Solar Cells ◽  
Band Gap ◽  
Carrier Concentration ◽  
High Efficiency ◽  
Energy Gap ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Doping Density ◽  
Cigs Solar Cells

We demonstrate an innovative CIGS-based solar cells model with a graded doping concentration absorber profile, capable of achieving high efficiency values. In detail, we start with an in-depth discussion concerning the parametrical study of conventional CIGS solar cells structures. We have used the wxAMPS software in order to numerically simulate cell electrical behaviour. By means of simulations, we have studied the variation of relevant physical and chemical parameters—characteristic of such devices—with changing energy gap and doping density of the absorber layer. Our results show that, in uniform CIGS cell, the efficiency, the open circuit voltage, and short circuit current heavily depend on CIGS band gap. Our numerical analysis highlights that the band gap value of 1.40 eV is optimal, but both the presence of Molybdenum back contact and the high carrier recombination near the junction noticeably reduce the crucial electrical parameters. For the above-mentioned reasons, we have demonstrated that the efficiency obtained by conventional CIGS cells is lower if compared to the values reached by our proposed graded carrier concentration profile structures (up to 21%).

scholarly journals Integrating Concentrated Optics for Ambient Perovskite Solar Cells

Energies ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2714
Author(s):  
Maria Khalid ◽  
Anurag Roy ◽  
Shubhranshu Bhandari ◽  
Senthilarasu Sundaram ◽  
Tapas K. Mallick
Keyword(s):  
Solar Cells ◽  
Solar Irradiance ◽  
High Efficiency ◽  
Low Cost ◽  
Short Circuit ◽  
Perovskite Solar Cells ◽  
Short Circuit Current ◽  
Initial Assessment ◽  
Pv System ◽  
Rapid Improvement

Metal halide perovskite solar cells (PSCs) are considered an effectual way to enhance photovoltaic (PV) properties, leading to low-cost and high efficiency. PSCs have experienced rapid improvement in the last ten years. The device’s energy production increases extensively in the presence of concentrated light. The use of concentrated optics in solar cells has spurred the PV industry towards tremendous research. Incorporating the concentrated optic into the PV system as a concentrated PV (CPV) means it can capture light effectively and operate at increased efficiencies under concentrated irradiance. This work addresses an initial assessment of the power conversion efficiency (PCE) enhancement of the ambient PSCs by externally integrating concentrated optics. Significantly, the concentrated optics exhibit ~90% of the PCE enhancement under the solar irradiance of 400 W/m2, whereas 16% of the PCE increase was observed when the solar irradiance changed to 1000 W/m2. During optics integration, a considerable elevation of short-circuit current predominately facilitated the overall efficiency enhancement of the PSC. A systematic PV parameters effect on the optic integration on PSCs was further scrutinized. Therefore, this work signifies a possible way to alleviate the PCE of carbon-based PSC using concentrated optics. This work focuses on integrating CPVs into PSCs, preventing PSC stability and scalability issues, with light conditioning techniques.

scholarly journals Performance of Natural Dye Extracted from Annatto, Black Plum, Turmeric, Red Spinach, and Cactus as Photosensitizers in TiO2NP/TiNT Composites for Solar Cell Applications

2021 ◽  
Vol 2021 ◽  
pp. 1-12
Author(s):  
Shibu Joseph ◽  
Albin John P. Paul Winston ◽  
S. Muthupandi ◽  
P. Shobha ◽  
S. Mary Margaret ◽  
...  
Keyword(s):  
Solar Cell ◽  
Low Cost ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Photovoltaic Properties ◽  
Ft Ir ◽  
Conversion Efficiencies ◽  
Sensitized Solar Cells

This paper is aimed at how to select, extract, and characterize natural dyes and to use them as sensitizers in dye-sensitized solar cells (DSSCs). Dyes obtained from fresh sources of annatto fruits, black plums, cactus fruits, turmeric roots, and red spinach leaves were used as sensitizers. The dye pigments were analyzed using UV-Vis spectrophotometer and FT-IR for the characterization of their spectral properties. The combination from Titanium dioxide paste with the powdered nanotubes was used as photoanodes for DSSCs. The photovoltaic properties of the DSSCs such as efficiency, fill factor, open-circuit voltage, and short circuit current were studied using a standard illumination of air-mass 1.5 global (AM 1.5 G) having an irradiance of 100 mW/cm2. The highest power conversion efficiencies (η) of 0.7% was achieved for the DSSCs fabricated using dye extracted from annatto fruits and 0.4% each for dyes extracted from black plum fruits and cactus fruits, respectively. The widespread accessibility of these fruits, roots, and leaves and ease of extraction of dyes from these ordinarily available natural resources render them unique and low-cost candidates for solar cell fabrication.

scholarly journals Damp-Heat Induced Performance Degradation for InGaP/GaAs/Ge Triple-Junction Solar Cell

2014 ◽  
Vol 2014 ◽  
pp. 1-6 ◽  
Author(s):  
Hwen-Fen Hong ◽  
Tsung-Shiew Huang ◽  
Wu-Yih Uen ◽  
Yen-Yeh Chen
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Conversion Efficiency ◽  
Triple Junction ◽  
Fill Factor ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Energy Conversion Efficiency ◽  
Open Circuit

We performed accelerated tests on sealed and nonsealed InGaP/InGaAs/Ge triple-junction (TJ) solar cells in a complex high temperature and high humidity environment and investigated the electrical properties over time. The degradation of energy conversion efficiency in nonsealed cells was found to be more serious than that in sealed cells. The short-circuit current (ISC), open-circuit voltage (VOC), and fill factor (FF) of sealed cells changed very slightly, though the conversion efficiency decreased 3.6% over 500 h of exposure. This decrease of conversion efficiency was suggested to be due to the deterioration of silicone encapsulant. TheISC,VOC, and FF of nonsealed cells decreased with increasing exposure time. By EL and SEM analysis, the root causes of degradation can be attributed to the damage and cracks near the edge of cells induced by the moisture ingress. It resulted in shunt paths that lead to a deterioration of the conversion efficiency of solar cell by increasing the leakage current, as well as decreasing open-circuit voltage and fill factor of nonsealed solar cells.

Sign in / Sign up

Export Citation Format

Share Document