scholarly journals Investigation of Low-Cost Surface Processing Techniques for Large-Size Multicrystalline Silicon Solar Cells

2010 ◽  
Vol 2010 ◽  
pp. 1-6 ◽  
Author(s):  
Yuang-Tung Cheng ◽  
Jyh-Jier Ho ◽  
William J. Lee ◽  
Song-Yeu Tsai ◽  
Yung-An Lu ◽  
...  
Keyword(s):  
Solar Cells ◽  
Silicon Nitride ◽  
Conversion Efficiency ◽  
High Efficiency ◽  
Short Circuit ◽  
Open Circuit ◽  
Multicrystalline Silicon ◽  
Double Layers ◽  
Large Size ◽  
Si Solar Cells

The subject of the present work is to develop a simple and effective method of enhancing conversion efficiency in large-size solar cells using multicrystalline silicon (mc-Si) wafer. In this work, industrial-type mc-Si solar cells with area of125×125 mm2were acid etched to produce simultaneouslyPOCl3emitters and silicon nitride deposition by plasma-enhanced chemical vapor deposited (PECVD). The study of surface morphology and reflectivity of different mc-Si etched surfaces has also been discussed in this research. Using our optimal acid etching solution ratio, we are able to fabricate mc-Si solar cells of 16.34% conversion efficiency with double layers silicon nitride (Si3N4) coating. From our experiment, we find that depositing double layers silicon nitride coating on mc-Si solar cells can get the optimal performance parameters. Open circuit (Voc) is 616 mV, short circuit current (Jsc) is 34.1 mA/cm2, and minority carrier diffusion length is 474.16 μm. The isotropic texturing and silicon nitride layers coating approach contribute to lowering cost and achieving high efficiency in mass production.

Simulation of InAIN/Si Single-Heterojunction Solar Cells Using wxAMPS

2014 ◽  
Vol 665 ◽  
pp. 111-114 ◽  
Author(s):  
Ying Huang ◽  
Xiao Ming Shen ◽  
Xiao Feng Wei
Keyword(s):  
Solar Cells ◽  
Fill Factor ◽  
High Efficiency ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Indium Content ◽  
Open Circuit ◽  
Heterojunction Solar Cells ◽  
Si Solar Cells

In this paper, InAlN/Si single-heterojunction solar cells have been theoretically simulated based on wxAMPS software. The photovoltaic parameters, such as open circuit voltage, short circuit current, fill factor and conversion efficiency were investigated with changing the indium content and thickness of n-InAlN layer. Simulation results show that the optimum efficiency of InAlN/Si solar cells is 23.1% under AM 1.5G spectral illuminations, with the indium content and thickness of n-InAlN layer are 0.65 and 600nm, respectively. The simulation would contribute to design and fabricate high efficiency InAlN/Si solar cells in experiment.

High-Efficiency HIT Solar Cells for Excellent Power Generating Properties

2008 ◽  
Vol 1123 ◽  
Author(s):  
Toshihiro Kinoshita ◽  
Daisuke Ide ◽  
Yasufumi Tsunomura ◽  
Shigeharu Taira ◽  
Toshiaki Baba ◽  
...  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Conversion Efficiency ◽  
Production Cost ◽  
High Efficiency ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Open Circuit ◽  
Surface Recombination Velocity ◽  
Dominant Factor

AbstractIn order to achieve the widespread use of HIT (Hetero-junction with I etero-Intrinsic T ntrinsic Thin-layer) solar cells, it is important to reduce the power generating cost. There are three main approaches for reducing this cost: raising the conversion efficiency of the HIT cell, using a thinner wafer to reduce the wafer cost, and raising the open circuit voltage to obtain a better temperature coefficient. With the first approach, we have achieved the highest conversion efficiency values of 22.3%, confirmed by AIST, in a HIT solar cell. This cell has an open circuit voltage of 0.725 V, a short circuit current density of 38.9 mA/cm2 and a fill factor of 0.791, with a cell size of 100.5 cm2. The second approach is to use thinner Si wafers. The shortage of Si feedstock and the strong requirement of a lower sales price make it necessary for solar cell manufacturers to reduce their production cost. The wafer cost is an especially dominant factor in the production cost. In order to provide low-priced, high-quality solar cells, we are trying to use thinner wafers. We obtained a conversion efficiency of 21.4% (measured by Sanyo) for a HIT solar cell with a thickness of 85μm. Even better, there was absolutely no sagging in our HIT solar cell because of its symmetrical structure. The third approach is to raise the open circuit voltage. We obtained a remarkably higher Voc of 0.739 V with the thinner cell mentioned above because of its low surface recombination velocity. The high Voc results in good temperature properties, which allow it to generate a large amount of electricity at high temperatures.

scholarly journals 17.6% Conversion Efficiency Multicrystalline Silicon Solar Cells Using the Reactive Ion Etching with the Damage Removal Etching

2012 ◽  
Vol 2012 ◽  
pp. 1-6 ◽  
Author(s):  
Ji-Myung Shim ◽  
Hyun-Woo Lee ◽  
Kyeong-Yeon Cho ◽  
Jae-Keun Seo ◽  
Ji-Soo Kim ◽  
...  
Keyword(s):  
Solar Cells ◽  
Conversion Efficiency ◽  
Short Circuit ◽  
Reactive Ion Etching ◽  
Open Circuit ◽  
Multicrystalline Silicon ◽  
Textured Surface ◽  
Textured Surfaces ◽  
Ion Etching ◽  
Selective Emitter

For lower reflectance, we applied a maskless plasma texturing technique using reactive ion etching (RIE) on acidic-textured multicrystalline silicon (mc-Si) wafer. RIE texturing had a deep and narrow textured surface and showed excellent low reflectance. Due to plasma-induced damage, unless the RIE-textured surfaces have the proper damage removal etching (DRE), they have a drop inVocand FF. RIE texturing with a proper DRE had sufficiently higher short circuit current(Isc)than acidic-textured samples without a drop in open circuit voltage(Voc). And in order to improve efficiency of mc-Si solar cell, we applied RIE texturing with optimized DRE condition to selective emitter structure. In comparison with the acidic-textured solar cells, RIE-textured solar cells have above 200 mA absolute gain in Isc. And optimized RIE samples with a DRE by HNO3/HF mixture showed 17.6% conversion efficiency, which were made using an industrial screen printing process with selective emitter structure.

Fabrication of the Large-Area Integrated a-Si Solar Cells

1986 ◽  
Vol 70 ◽  
Author(s):  
S. Yamazaki ◽  
M. Abe ◽  
S. Nagayama ◽  
K. Shibata ◽  
M. Susukida ◽  
...  
Keyword(s):  
Solar Cells ◽  
Standard Deviation ◽  
Conversion Efficiency ◽  
Fill Factor ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Process Equipment ◽  
Large Area ◽  
Si Solar Cells

ABSTRACTPIN-structure small-area solar cells using a-Si have been frequently reported on, but only a few reports are available on the study of solar cells using a large-area (10-cm square) substrate, all with a resultant conversion efficiency of above 9.0 %[1,2]. Our study has been concentrated on solar cells using a batch of ten 10-cm square substrates with an average conversion efficiency of 9.5 % or more.As a result, without an anti-reflection coating on the surface of the glass substrate, the following values have been obtained: average conversion efficiency (EFF)=9.63 % (standard deviation of 0.195 %) -Open-circuit voltage (Voc)=12.668 V (standard deviation of 0.215 V) -Short-circuit current (Isc)=78.467 mA (standard deviation of 1.619 mA) -Fill factor (FF)=0.6672 (standard deviation of 0.009)The process, equipment and methods for measurements through which these results were obtained are described below.

Numerical Simulation on Effects of TCO Work Function on Performance of a-Si:H Solar Cells

2019 ◽  
Vol 966 ◽  
pp. 501-506
Author(s):  
Ahmad Sholih ◽  
Dadan Hamdani ◽  
Sigit Tri Wicaksono ◽  
Mas Irfan P. Hidayat ◽  
Yoyok Cahyono ◽  
...  
Keyword(s):  
Solar Cells ◽  
Work Function ◽  
Conversion Efficiency ◽  
High Efficiency ◽  
Low Cost ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Conducting Oxides ◽  
Conversion Efficiencies

In this paper, we have investigated the effect of the work function of transparent conducting oxides (TCO) on the performance of a-Si:H p-i-n solar cells, including open circuit voltage (VOC), short circuit current (JSC), fill factor (FF) and conversion efficiency, using AFORS-HET software. The simulation has focused on two layers: front contact work function (ΦTCO-front) and back contact work function (ΦTCO-back) with various band from 4.7 eV to 5.3 eV and 4.2 eV to 4.9 eV respectively. From the simulation results, we know that the work function of TCO greatly affects the performance of solar cells such as Voc, Jsc, FF and conversion efficiency. By optimization, we arrive at results for Voc, Jsc, FF and conversion efficiencies of 0.88 V, 8.95 mA / cm2, 65% and 5.1% respectively. This result is obtained on ΦTCO-front 5.2 eV. When ΦTCO-front 5.2 eV, the value of VOC, FF and conversion efficiency has been saturated, while the value of the J sc actually begins to decrease. Furthermore, when the ΦTCO - back is 4.3 eV, we get the best results for VOC, Jsc, FF and conversion Efficiency of 0.9 V, 8.96 mA / cm2, 73 % and 5.9 % respectively. When ΦTCO-back 4.3 eV, the value of VOC, FF and conversion efficiency begins to decrease, while the value of the Jsc does’t change significantly. These optimizations may help in producing low cost high efficiency p-i-n solar cells experimentally.

17.8%-efficient Amorphous Silicon Heterojunction Solar Cells on p-type Silicon Wafers

2006 ◽  
Vol 910 ◽  
Author(s):  
Qi Wang ◽  
Matt P. Page ◽  
Eugene Iwancizko ◽  
Yueqin Xu ◽  
Yanfa Yan ◽  
...  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Amorphous Silicon ◽  
High Efficiency ◽  
Short Circuit ◽  
Open Circuit ◽  
Layer Growth ◽  
Surface Recombination Velocity ◽  
Back Contact ◽  
P Type

AbstractWe have achieved an independently-confirmed 17.8% conversion efficiency in a 1-cm2, p-type, float-zone silicon (FZ-Si) based heterojunction solar cell. Both the front emitter and back contact are hydrogenated amorphous silicon (a-Si:H) deposited by hot-wire chemical vapor deposition (HWCVD). This is the highest reported efficiency for a HWCVD silicon heterojunction (SHJ) solar cell. Two main improvements lead to our most recent increases in efficiency: 1) the use of textured Si wafers, and 2) the application of a-Si:H heterojunctions on both sides of the cell. Despite the use of textured c-Si to increase the short-circuit current, we were able to maintain the same 0.65 V open-circuit voltage as on flat c-Si. This is achieved by coating a-Si:H conformally on the c-Si surfaces, including covering the tips of the anisotropically-etched pyramids. A brief atomic H treatment before emitter deposition is not necessary on the textured wafers, though it was helpful in the flat wafers. It is essential to high efficiency SHJ solar cells that the emitter grows abruptly as amorphous silicon, instead of as microcrystalline or epitaxial Si. The contact on each side of the cell comprises a thin (< 5 nm) low substrate temperature (~100°C) intrinsic a-Si:H layer, followed by a doped layer. Our intrinsic layers are deposited at 0.3-1.2 nm/s. The doped emitter and back-contact layers were deposited at a higher temperature (>200°C) and grown from PH3/SiH4/H2 and B2H6/SiH4/H2 doping gas mixtures, respectively. This combination of low (intrinsic) and high (doped layer) growth temperatures was optimized by lifetime and surface recombination velocity measurements. Our rapid efficiency advance suggests that HWCVD may have advantages over plasma-enhanced (PE) CVD in fabrication of high-efficiency heterojunction c-Si cells; there is no need for process optimization to avoid plasma damage to the delicate, high-quality, Si wafers.

scholarly journals Dye-Sensitized Nanocrystalline ZnO Solar Cells Based on Ruthenium(II) Phendione Complexes

2011 ◽  
Vol 2011 ◽  
pp. 1-10 ◽  
Author(s):  
Hashem Shahroosvand ◽  
Parisa Abbasi ◽  
Mohsen Ameri ◽  
Mohammad Reza Riahi Dehkordi
Keyword(s):  
Thin Film ◽  
Solar Cells ◽  
Conversion Efficiency ◽  
Short Circuit ◽  
Photocurrent Density ◽  
Open Circuit ◽  
Zno Thin Film ◽  
Photovoltaic Properties ◽  
Dye Sensitized ◽  
Ft Ir

The metal complexes ( (phen)2(phendione))(PF6)2(1), [ (phen)(bpy)(phendione))(PF6)2(2), and ( (bpy)2(phendione))(PF6)2(3) (phen = 1,10-phenanthroline, bpy = 2,2′-bipyridine and phendione = 1,10-phenanthroline-5,6-dione) have been synthesized as photo sensitizers for ZnO semiconductor in solar cells. FT-IR and absorption spectra showed the favorable interfacial binding between the dye-molecules and ZnO surface. The surface analysis and size of adsorbed dye on nanostructure ZnO were further examined with AFM and SEM. The AFM images clearly show both, the outgrowth of the complexes which are adsorbed on ZnO thin film and the depression of ZnO thin film. We have studied photovoltaic properties of dye-sensitized nanocrystalline semiconductor solar cells based on Ru phendione complexes, which gave power conversion efficiency of (η) of 1.54% under the standard AM 1.5 irradiation (100 mW cm−2) with a short-circuit photocurrent density () of 3.42 mA cm−2, an open-circuit photovoltage () of 0.622 V, and a fill factor (ff) of 0.72. Monochromatic incident photon to current conversion efficiency was 38% at 485 nm.

Effect of temperature on organic Schottky barrier cells

1981 ◽  
Vol 59 (6) ◽  
pp. 727-732 ◽  
Author(s):  
Rafik O. Loutfy ◽  
Cheng-Kuo Hsiao
Keyword(s):  
Solar Cells ◽  
Power Conversion Efficiency ◽  
Schottky Barrier ◽  
Conversion Efficiency ◽  
Organic Solar Cells ◽  
Short Circuit ◽  
Power Conversion ◽  
Open Circuit ◽  
Effect Of Temperature ◽  
Photovoltaic Properties

The effect of temperature on the photovoltaic properties of indium/metal-free phthalocyanine Schottky barrier solar cells was investigated in the range 260–350 K. In general, the short circuit photocurrent, Jsc, and fill factor, ff, increased with increasing temperature (in contrast to inorganic photocells). The device series resistance and open circuit photovoltage, Voc, decreased (similar to inorganic photocells) as temperature was raised. An increase in the overall power conversion efficiency, η, has been observed with increase of temperature. In the case of x-H2Pc, the power conversion efficiency increased by 2.5 times due to a temperature rise of 60 °C above ambient. Thus, for operation at temperatures above ambient, organic solar cells may offer a significant advantage over inorganic cells.Analysis of the variation of the photovoltage with temperature showed that the decrease in Voc is mainly due to variation injunction impedance, which is controlled by thermionic current at high temperature and ionized impurity at low temperature.

The influence of emitter resistance on the electrical parameters of mono- and multicrystalline silicon solar cells

2019 ◽  
Vol 36 (3) ◽  
pp. 90-94
Author(s):  
Barbara Swatowska ◽  
Piotr Panek ◽  
Dagmara Michoń ◽  
Aleksandra Drygała
Keyword(s):  
Solar Cells ◽  
Contact Resistance ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Multicrystalline Silicon ◽  
Silicon Solar Cells ◽  
Electrical Parameters ◽  
Content Type ◽  
Diffusion Parameters

Purpose The purpose of this study was the comparison and analysis of the electrical parameters of two kinds of silicon solar cells (mono- and multicrystalline) of different emitter resistance. Design/methodology/approach By controlling of diffusion parameters, silicon mono- (Cz-Si) and multicrystalline (mc-Si) solar cells with different emitter resistance values were produced – 22 and 48 Ω/□. On the basis of current-voltage measurements of cells and contact resistance mapping, the properties of final solar cells based on two different materials were compared. Additionally, the influence of temperature on PV cells efficiency and open circuit voltage (Uoc) were investigated. The PC1D simulation was useful to determine spectral dependence of external quantum efficiency of solar cells with different emitter resistance. The silicon solar cells of 25 cm2 area and 240 µm thickness were investigated. Findings Considering the all stages of cell technology, the best structure is silicon solar cell with sheet resistance (Rsheet) of 45-48 Ω/□. Producing of an emitter with this resistance allowed to obtain cells with a fill factor between 0.725 and 0.758, Uoc between 585 and 612 mV, short circuit current (Isc) between 724 and 820 mA. Originality/value Measurements and analysis confirmed that mono- and multicrystalline silicon solar cells with 48 Ω/□ emitter resistance have better parameters than cells with Rsheet of 22 Ω/□. The contact resistance is the highest for mc-Si with Rsheet of 48 Ω/□ and reaches the value 3.8 Ωcm.

scholarly journals Analytical Study of the Electrical Output Characteristics of c-Si Solar Cells by Cut and Shading Phenomena

Energies ◽  
2018 ◽  
Vol 11 (12) ◽  
pp. 3397 ◽  
Author(s):  
Jong Lim ◽  
Woo Shin ◽  
Hyemi Hwang ◽  
Young-Chul Ju ◽  
Suk Ko ◽  
...  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Crystalline Silicon ◽  
Short Circuit ◽  
Incident Light ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Si Solar Cell ◽  
Si Solar Cells ◽  
Electrical Output

Cut solar cells have received considerable attention recently as they can reduce electrical output degradation when the c-Si solar cells (crystalline-silicon solar cells) are shaded. Cut c-Si solar cells have a lower short-circuit current than normal solar cells and the decrease in short-circuit currents is similar to the shading effect of c-Si solar cells. However, the results of this study’s experiment show that the shadow effect of a c-Si solar cell reduces the V o c (open circuit voltage) in the c-Si solar cell but the V o c does not change when the c-Si solar cell is cut because the amount of incident light does not change. In this paper, the limitations of the electrical power analysis of the cut solar cells were identified when only photo current was considered and the analysis of the electric output of the cut c-Si solar cells was interpreted with a method different from that used in previous analyses. Electrical output was measured when the shaded and cut rates of c-Si solar cells were increased from 0% to 25, 50 and 75%, and a new theoretical model was compared with the experimental results using MATLAB.

Sign in / Sign up

Export Citation Format

Share Document