Assessment of Ride Comfort and Braking Performance Using Energy-Harvesting Shock Absorber

2015 ◽  
Vol 8 (2) ◽  
pp. 482-491 ◽  
Author(s):  
Liangyao Yu ◽  
Shuhao Huo ◽  
WenWei Xuan ◽  
Lei Zuo
Keyword(s):  
Energy Harvesting ◽  
Shock Absorber ◽  
Ride Comfort ◽  
Braking Performance

Performances of Energy-Harvesting Shock Absorbers on Various Types of Vehicles

2015 ◽  
Author(s):  
Sijing Guo ◽  
Lin Xu ◽  
Yilun Liu ◽  
Xuexun Guo ◽  
Lei Zuo
Keyword(s):  
Energy Harvesting ◽  
Vehicle Dynamics ◽  
Degrees Of Freedom ◽  
Large Scale ◽  
Shock Absorber ◽  
Ride Comfort ◽  
Rotational Inertia ◽  
Shock Absorbers ◽  
Regenerative Shock Absorber ◽  
Comprehensive Study

Energy-Harvesting Shock Absorber (EHSA), as a large-scale energy-harvesting mechanism for recovering suspension vibration energy, has been studied for years. A design of the regenerative shock absorber with Mechanical Motion Rectifier (MMR) has been proved to be more reliable and efficient. This paper reports a comprehensive study of the influence of MMR-based Energy-Harvesting Shock Absorber (MMR-EHSA) on vehicle dynamics performances. Models of MMR-EHSA and vehicle with MMR-EHSA with two degrees of freedom are created. Simulations are conducted on five typical vehicles, including passenger car, bus and three types of trucks. The ride characteristics of comfort, road handling and energy recovery are evaluated on these vehicles under various MMR rotational inertia and harvesting damping. The simulation results show that MMR-EHSA is able to improve both the ride comfort and road handling simultaneously under certain conditions over the traditional shock absorbers, which broadens our knowledge of MMR-EHSA’s applicable scenarios.

Performance Evaluation of Train Suspension Energy Harvesting Shock Absorber on Railway Vehicle Dynamics

2018 ◽  
Author(s):  
Yu Pan ◽  
Sijing Guo ◽  
Ruijin Jiang ◽  
Yong Xu ◽  
Zhiwen Tu ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Vehicle Dynamics ◽  
Shock Absorber ◽  
Ride Comfort ◽  
Average Power ◽  
Modern Society ◽  
Railway Vehicle ◽  
Railway Transportation ◽  
Suspension Dynamics ◽  
Secondary Suspension

Railway transportation has been increasingly significant for modern society in recent decades. To enable smart technology, such as health monitoring and electromagnetic braking for railway vehicles, a mechanical motion rectifier (MMR) based energy harvesting shock absorber (EHSA) has been proposed and proved to be capable of scavenging energy from the train suspension vibration. When installed on the train, MMR-EHSA works as a tunable damper in parallel with an inerter. This new suspension form brings great potential for further optimization of suspension dynamics but is rarely researched before. In this paper, the influence of the energy harvesting shock absorber (EHSA) on the railway vehicle dynamics performance is studied. A ten-degree of freedom vehicle model is established, with MMR shock absorber’s nonlinearity taken into account, with the purpose to analyze the influence of the EHSA on the ride comfort and wheel-rail vertical forces. Simulations are conducted by replacing the traditional shock absorber from train secondary suspension with the EHSA. Results show that EHSA could respectively harvest 180 W and 40 W average power at AAR 6th and 5th rail irregularity. In addition, compared with the traditional shock absorber, the MMR-EHSA can provide a higher ride comfort for passengers and slightly reduce the wheel-rail contact force.

Design of combined brake system for light weight scooters

2021 ◽  
pp. 095440702110240
Author(s):  
Yuan-Ting Lin ◽  
Chyuan-Yow Tseng ◽  
Jao-Hwa Kuang ◽  
Yeong-Maw Hwang
Keyword(s):  
Ride Comfort ◽  
Brake System ◽  
Force Distribution ◽  
Test Results ◽  
Systematic Method ◽  
Braking Performance ◽  
Evaluation Indexes ◽  
Low Costs ◽  
Braking Force ◽  
Good Agreement

The combined brake system (CBS) is a mechanism that links the front and rear brakes for scooters. For two-wheeled scooters, a CBS with appropriate braking force distribution can reduce the risk of crashing accidents due to insufficient driving proficiency. The design of the braking force distribution for a CBS is challenging to the designer because it has to fulfill many requirements such as braking performance, ride comfort, reliability, and low costs. This paper proposes a systematic method to optimize the parameters of CBS. The evaluation indexes for the design are first discussed. The steps to determine the critical parameter to meet the indexes and a method to predict braking performance are developed. Finally, driving tests are carried out to verify the effectiveness of the proposed method. Experimental results showed that the deceleration of the tested scooter equipped with the designed CBS achieves an average mean fully developed deceleration (MFDD) of 5.246 m/s2, higher than the homologation requirement. Furthermore, the proposed method’s prediction of braking performance is in good agreement with the test results, with errors <1%.

Variation in Automotive Shock Absorber Damping Characteristics & amp; Their Effects on Ride Comfort Attribute and Vehicle Yaw Response

2021 ◽  
Author(s):  
Satyaranjan Sahoo ◽  
Eric Pranesh De Reuben ◽  
Deepak BAKSHI ◽  
Hari Krishnan ◽  
Amardeep Singh
Keyword(s):  
Shock Absorber ◽  
Ride Comfort ◽  
Damping Characteristics

scholarly journals Development of the Electromagnetic Regenerative Shock Absorber as an Energy Harvesting Tool for Vehicles

2019 ◽  
Vol 1 (3) ◽  
pp. 31-42
Author(s):  
Wanda Afnison ◽  
Erzeddin Alwi ◽  
Hasan Maksum ◽  
Bahrul Amin ◽  
M Yasep Setiawan
Keyword(s):  
Energy Harvesting ◽  
Shock Absorber ◽  
Electrical Energy ◽  
Test Results ◽  
Vibration Energy Harvesting ◽  
Energy Mechanism ◽  
Left And Right ◽  
Type Magnet ◽  
Regenerative Shock Absorber ◽  
Further Development

This research is a development of previous research entitled "Designing Regenerative Shock Absorber as a Vibration Energy Harvesting Tool on Vehicles" in the PUPT scheme funded by PNBP UNP 2017. In this study optimization of design oriented to energy generation was carried out while also paying attention to aspects driving comfort that might change due to the installation of a harvesting energy mechanism. One aspect of the change occurred in the type of magnet used, namely a ring type magnet with a type of neodymium material.From the test results obtained by changing the value of the efficiency of the shock absorber after the ERSA mechanism is installed by 2%, this condition also has an impact on the dissimilarity of the attenuation value obtained by 2% for the front-rear (left) and (right) wheels. In terms of generation voltage obtained the maximum generation voltage obtained is 25,600 mV. Based on the data obtained, it needs further development ERSA, especially in the aspect of the electromagnetic mechanism to optimize the generation of electrical energy.

An Innovative Energy Harvesting Shock Absorber System for Motorbikes

2021 ◽  
pp. 1-11
Author(s):  
Alejandro Gonzalez ◽  
Jose Luis Olazagoitia ◽  
Jordi Vinolas ◽  
Ibai Ulacia ◽  
Mikel Izquierdo
Keyword(s):  
Energy Harvesting ◽  
Shock Absorber

scholarly journals Modeling and Analysis of a Hydraulic Energy-Harvesting Shock Absorber

2020 ◽  
Vol 2020 ◽  
pp. 1-11 ◽  
Author(s):  
Zhifei Wu ◽  
Guangzhao Xu
Keyword(s):  
Energy Harvesting ◽  
External Load ◽  
Energy Recovery ◽  
Shock Absorber ◽  
Load Resistance ◽  
Hydraulic Motor ◽  
Damping Force ◽  
Modeling And Analysis ◽  
Unidirectional Flow ◽  
Energy Dissipated

This paper proposes a hydraulic energy-harvesting shock absorber prototype, which realizes energy harvesting of the vibration energy dissipated by the automobile suspension system. The structural design of the proposed shock absorber ensures that the unidirectional flow of oil drives the hydraulic motor to generate electricity while obtaining an asymmetrical extension/compression damping force. A mathematical model of the energy-harvesting shock absorber is established, and the simulation results indicate that the damping force can be controlled by varying the load resistance of the feed module, thus adjusting the required damping force ratio of the compression and recovery strokes. By adjusting the external load, the target indicator performance of the shock absorber is achieved while obtaining the required energy recovery power. A series of experiments are conducted on the prototype to verify the validity of the damping characteristics and the energy recovery efficiency as well as to analyze the effect of external load and excitation speed on these characteristics.

A Novel Energy-Harvesting Active Radial Bogie for Railway Vehicles: Design, Simulation and HIL Test

2015 ◽  
Vol 733 ◽  
pp. 695-698
Author(s):  
Shu Shu Wang ◽  
Xiao Meng Shen ◽  
Xiao Jian Tu
Keyword(s):  
Energy Harvesting ◽  
Shock Absorber ◽  
Vertical Vibration ◽  
Vibration Energy ◽  
Railway Transportation ◽  
Railway Vehicles ◽  
Rail Vehicles ◽  
Simulation Results ◽  
Regenerative Shock Absorber ◽  
And Control

With the increasing development of railway transportation, the wheel-rail wearing problem is becoming more and more serious while the increasing of both the operating speed and loading weight of railway vehicles. Active radial bogie is one of the hotspots for research in the area of decreasing the wheel-rail wearing issues. Meanwhile, the energy dissipation problem has been restricting its development. This paper puts forward a novel energy-harvesting active radial bogie for rail vehicles. Making use of the hydraulic electromagnetic energy-regenerative shock absorber, the vertical vibration energy could be harvested while train is traveling. Detailed study and evaluation for this active radial bogie will be presented. The tests and simulation results prove the effectiveness of the proposed bogie mechanism and control.

scholarly journals Experimentally validated dynamic results of a relaxation-type quarter car suspension with an adjustable damper

2017 ◽  
Vol 36 (2) ◽  
pp. 148-159 ◽  
Author(s):  
AN Thite ◽  
F Coleman ◽  
M Doody ◽  
N Fisher
Keyword(s):  
Shock Absorber ◽  
Ride Comfort ◽  
Damping Ratio ◽  
Closed Form Solution ◽  
Nonlinear Function ◽  
Frequency Domain Analysis ◽  
Form Solution ◽  
Damping Coefficient ◽  
Design Stage ◽  
Quarter Car

Models of varying degree of sophistication are used in vehicle dynamic studies. For ride comfort, Kelvin–Voigt arrangement is preferred and for impact harshness analysis, a relaxation-type suspension model, Zener or Maxwell type is used. The nonconsideration of relaxation-type models in ride comfort studies can result in significant errors for frequencies below ∼30 Hz. The object of the paper is to show the influence of the series stiffness on the effective suspension damping both experimentally and numerically. A frequency domain analysis of two-degree of freedom Zener quarter car model is performed to find the complex relation between effective damping coefficient and the limiting value of damping ratio for a given series stiffness. The nonlinear relation between shock absorber damping and the natural frequencies is clearly illustrated. A novel four-post rig set-up is used to validate the results by measuring transmissibilities, giving damping ratios for varying shock absorber settings. A closed form solution, based on a simplified partial model, of optimal damping coefficient, which is a nonlinear function of stiffnesses, shows good agreement with numerical simulations of the complete system. The nonlinearities in shock absorbers also influence the outcome. These findings can be a great value at early design stage.

Sign in / Sign up

Export Citation Format

Share Document