Response Ratio Development for Lateral Pendulum Impact with Porcine Thorax and Abdomen Surrogate Equivalents

2020 ◽  
Author(s):  
Jennifer L. Yaek ◽  
John M. Cavanaugh ◽  
Stephen W. Rouhana
Water ◽  
2021 ◽  
Vol 13 (5) ◽  
pp. 603
Author(s):  
Hojung You ◽  
Rafael O. Tinoco

Acoustic deterrents are recognized as a promising method to prevent the spread of invasive grass carp, Ctenopharyngodon idella (Valenciennes, 1844) and the negative ecological impacts caused by them. As the efficacy of sound barriers depends on the hearing capabilities of carp, it is important to identify whether carps can recognize acoustic signals and alter their swimming behavior. Our study focuses on quantifying the response of grass carp larvae when exposed to out-of-water acoustic signals within the range of 100–1000 Hz, by capturing their movement using particle-tracking velocimetry (PTV), a quantitative imaging tool often used for hydrodynamic studies. The number of responsive larvae is counted to compute response ratio at each frequency, to quantify the influence of sound on larval behavior. While the highest response occurred at 700 Hz, we did not observe any clear functional relation between frequency of sound and response ratio. Overall, 20–30% of larvae were consistently reacting to sound stimuli regardless of the frequency. In this study, we emphasize that larval behaviors when exposed to acoustic signals vary by individual, and thus a sufficient number of larvae should be surveyed at the same time under identical conditions, to better quantify their sensitivity to sound rather than repeating the experiment with individual specimens. Since bulk quantification, such as mean or quantile velocities of multiple specimens, can misrepresent larval behavior, our study finds that including the response ratio can more effectively reflect the larval response.


Author(s):  
Tien-Chih Lin ◽  
Nikhil Gupta

Hollow particle (microballoon) filled polymeric composites, called syntactic foams, are tested for impact properties in the present work. Izod type pendulum impact testing is carried out on eight types of foams, which are made of four types of microballoons used in volume fractions of 0.5 and 0.6. Variation in the volume fraction of microballoons leads to a difference in the total energy absorbed during fracture of different types of foams. Results show that syntactic foams containing microballoons of lower density show lower impact strength because of the lower strength of these microballoons. An increase in microballoon volume fraction leads to decreased energy absorption and strength.


Perfusion ◽  
1996 ◽  
Vol 11 (2) ◽  
pp. 125-130 ◽  
Author(s):  
Ian J Reece ◽  
Gerrard Linley ◽  
Habib Al Tareif ◽  
Rollie DeVroege ◽  
Jitesh Tolia ◽  
...  

Author(s):  
Philip Coppens ◽  
Anna Makal ◽  
Bertrand Fournier ◽  
Katarzyna N. Jarzembska ◽  
Radosław Kamiński ◽  
...  

In picosecond and slower pump–probe diffraction experiments, collection of response–ratio correlation sets prior to full data collection provides an invaluable confirmation of the existence of a light-induced signal prior to full data collection. If a response to light exposure is observed, the quality of the data being collected can be assessed. A number of such correlation plots both for synchrotron and in-house pump–probe data collection are presented.


Author(s):  
Melanie Stephan ◽  
Jens O. Weber ◽  
Ulrich Wuttke ◽  
Christina Berger

Bolted joints are a major part of wind energy plants. Due to climatic conditions, they are often exposed to temperatures far below the freezing point. Together with the multiaxial state of stress, which results from the notch effect of the thread, and possible dynamic overloads during operation, sufficient ductility of the material is needed. The state of the art method to investigate the ductile behavior of fasteners is the Charpy pendulum impact test with a V-notched specimen. According to international standard DIN EN ISO 898-1 [1] respectively ASTM F568M-07 [2], fasteners made of carbon steel and alloy steel with a body centered cubic lattice structure can be used for temperatures down to 223 K (−50°C, −58°F) as long as a minimum impact energy of 27 J at 253 K (−20°C, −4°F) is met. As there are several disadvantages in using this test method for fasteners, a detailed examination of existing test methods and design concepts is necessary to find alternatives to the Charpy pendulum impact test. Extensive quasi-static and dynamic material tests were conducted on fasteners with property classes 5.6, 10.9 and 12.9 in a temperature range between 203 K (−70°C, −94°F) and room temperature 293 K (20°C, 68°F). Both mechanical properties and the influence of different specimen geometries were evaluated. Analytical concepts for the description of the low temperature applicability of different steels were analyzed.


Sign in / Sign up

Export Citation Format

Share Document