scholarly journals Use of Digital Elevation Models to Map Out The Groundwater Resources Base Of Kuje Area to Federal Capital Territory, Abuja, Nigeria

2021 ◽  
Vol 25 (7) ◽  
pp. 1207-1212
Author(s):  
J.O. Mephors ◽  
C.O. Ogunmuyiwa ◽  
O.S. Afolabi ◽  
C.F. Agbor ◽  
O.M. Ogoliegbune ◽  
...  
Keyword(s):  
Ground Water ◽  
Sea Level ◽  
Digital Elevation Models ◽  
Groundwater Resources ◽  
Research Work ◽  
Groundwater Potential ◽  
Topographic Maps ◽  
Digital Elevation ◽  
The Government ◽  
Elevation Model

This research work examined the use of digital elevation model in the evaluation of groundwater resources in Kuje Area, Nigeria. This was achieved through the acquisition of topographic maps, Digitization of the topographic maps which were glued and interpolated to generate Digital Elevation Models (DEM) and Mapping of groundwater potential areas using ArcGIS 9.2 and ArcView 3.2a software. Findings from this research show that the study area have elevations ranging from 333 m to 429 m above sea level with a moderate groundwater potential in areas with elevation ranging from 286 m and 333 m above sea level. Some areas also have ground water problem, these areas were classified as mountainous areas and are located at very high elevations. The rocky nature of the high elevated environment makes these areas have very little hope of assessing groundwater. It was suggested that government should properly monitor groundwater, inhabitants should be made to accept laws which will help them in the conservation of ground water resources and efforts should also be made by the government towards creating incentives that will encourage people to obey these laws, Conservation methods such as retardation of surface runoff, control of vegetation and groundwater withdrawal rates should be employed.

scholarly journals COMPARATIVE ANALYSIS FOR METHODS OF BUILDING DIGITAL ELEVATION MODELS FROM TOPOGRAPHIC MAPS USING GEOINFORMATION TECHNOLOGIES

2021 ◽  
Vol 47 (4) ◽  
pp. 191-199
Author(s):  
Vadim Belenok ◽  
Yuriy Velikodsky ◽  
Oleksandr Nikolaienko ◽  
Nataliia Rul ◽  
Sergiy Kryachok ◽  
...  
Keyword(s):  
Digital Elevation Models ◽  
Complex Structure ◽  
Topographic Maps ◽  
Interpolation Methods ◽  
Contour Lines ◽  
Central Russian Upland ◽  
Digital Elevation ◽  
Elevation Data ◽  
The Russian Federation ◽  
Elevation Model

The article considers the question of estimating the accuracy of interpolation methods for building digital elevation models using Soviet topographic maps. The territory of the Kursk region of the Russian Federation was used as the study area, because it is located on the Central Russian Upland and characterized by the complex structure of the vertical and horizontal dissection of the relief. Contour lines automatically obtained using a Python algorithm were used as the initial elevation data to build a digital elevation model. Digital elevation models obtained by thirteen different interpolation methods in ArcGIS and Surfer software were built and analyzed. Special attention is paid to the ANUDEM method, which allows to obtain hydrologically correct digital elevation models. Recommendations for the use of one or another method of interpolation are given. The results can be useful for professionals who use topographic maps in their work and deals with the design using digital elevation models.

Quality Assessment of Globally Available Digital Elevation Model (DEM) for Mountainous Region

2021 ◽  
Vol 5 (1) ◽  
pp. 11-21
Author(s):  
Sangay Gyeltshen ◽  
Krisha Kumar Subedi ◽  
Laylo Zaridinova Kamoliddinovna ◽  
Jigme Tenzin
Keyword(s):  
Digital Elevation Model ◽  
Vertical Displacement ◽  
Satellite System ◽  
Topographic Map ◽  
Alos Palsar ◽  
Aster Gdem ◽  
Digital Elevation ◽  
The Government ◽  
Elevation Model ◽  
The Individual

The study assessed the accuracies of globally available Digital Elevation Models (DEM’s) i.e., SRTM v3, ASTER GDEM v2 and ALOS PALSAR DEM with respect to Topo-DEM derived from topographic map of 5m contour interval. 100 ground control points of the elevation data were collected with the help of kinematic hand held GNSS (Global Navigation Satellite System), randomly distributed over the study area. The widely used RMSE statistic, NCC correlation and sub-pixel-based approach were applied to evaluate the erroneous, correlation, horizontal and vertical displacement in terms of pixels for the individual Digital Elevation Model. Following these evaluations, SRTM DEM was found to be highly accurate in terms of RMSE and displacement compared to other DEMs. This study is intended to provide the researchers, GIS specialists and the government agencies dealing with remote sensing and GIS, a basic clue on accuracy of the DEMs so that the best model can be selected for application on various purposes of the similar region.

scholarly journals Paleovalleys mapping using remote sensing

2014 ◽  
Vol XL-5 ◽  
pp. 83-86
Author(s):  
A.B. Baibatsha
Keyword(s):  
Remote Sensing ◽  
Groundwater Resources ◽  
Alluvial Deposits ◽  
North East ◽  
Digital Elevation ◽  
Landsat 7 ◽  
Tectonic Zones ◽  
Materials Used ◽  
Elevation Model ◽  
Digital Elevation Model Data

For work materials used multispectral satellite imagery Landsat (7 channels), medium spatial resolution (14,25–90 m) and a digital elevation model (data SRTM). For interpretation of satellite images and especially their infrared and thermal channels allocated buried paleovalleys pre-paleogene age. Their total length is 228 km. By manifestation of the content of remote sensing paleovalleys distinctly divided into two types, long ribbon-like read in materials and space survey highlights a network of small lakes. By the nature of the relationship established that the second type of river paleovalleys flogs first. On this basis, proposed to allocate two uneven river paleosystem. The most ancient paleovalleys first type can presumably be attributed to karst erosion, blurry chalk and carbon deposits foundation. Paleovalleys may include significant groundwater resources as drinking and industrial purposes. Also we can control the position paleovalleys zinc and bauxite mineralization area and alluvial deposits include uranium mineralization valleys infiltration type and placer gold. Direction paleovalleys choppy, but in general they have a north-east orientation, which is controlled by tectonic zones of the foundation. These zones are defined as the burial place themselves paleovalleys and position of karst cavities in areas interfacing with other structures orientation. The association of mineralization to the caverns in the beds paleovalleys could generally present conditions of formation of mineralization and carry it to the "Niagara" type. The term is obviously best reflects the mechanism of formation of these ores.

High-Resolution Digital Elevation and Bathymetry Model for Tsunami Run-Up and Inundation Simulation in Penang

2019 ◽  
Vol 13 (05n06) ◽  
pp. 1941001
Author(s):  
Su Yean Teh ◽  
Hock Lye Koh ◽  
Yong Hui Lim
Keyword(s):  
High Resolution ◽  
Indian Ocean ◽  
Sea Level ◽  
Interpolation Method ◽  
Topographic Maps ◽  
Seamless Integration ◽  
Topographic Data ◽  
Digital Elevation ◽  
Run Up ◽  
Tsunami Run Up

Many beaches in Penang island were severely inundated by the 26 December 2004 Indian Ocean mega tsunami with 57 deaths recorded. It is anticipated that the next big tsunami will cause even more damages to beaches in Penang. Hence, developing community resilience against the risks of the next tsunami is essential. Resilience entails many interlinked components, beginning with a good understanding of the inundation scenarios critical to community evacuation and resilience preparation. Inundation scenarios are developed from tsunami simulations involving all three phases of tsunami generation, propagation and run-up. Accurate and high-resolution bathymetric–topographic maps are essential for simulations of tsunami wave inundation along beaches. Bathymetric maps contain information on the depths of landforms below sea level while topographic maps reveal the elevation of landforms above sea level. Bathymetric and topographic datasets for Malaysia are, however, currently not integrated and are available separately and in different formats, not suitable for inundation simulations. Bathymetric data are controlled by the National Hydrographic Centre (NHC) of the Royal Malaysian Navy while topographic data are serviced by the Department of Survey and Mapping Malaysia (JUPEM). It is highly desirable to have seamless integration of high-resolution bathymetric and topographic data for tsunami simulations and for other scientific studies. In this paper, we develop a robust method for integrating the NHC bathymetric and JUPEM topographic data into a regularly-spaced grid system essential for tsunami simulation. A primary objective of this paper is to develop the best Digital Elevation and Bathymetry Model (DEBM) for Penang based upon the most suitable and accurate interpolation method for integrating bathymetric and topographic data with minimal interpolation errors. We analyze four commonly used interpolation methods for generating gridded topographic and bathymetric surfaces, namely (i) Kriging, (ii) Multiquadric (MQ), (iii) Thin Plate Spline (TPS) and (iv) Inverse Distance to Power (IDP). The study illustrated that the Kriging interpolation method produces an integrated bathymetric and topographic surface that best approximates the admiralty nautical chart of Penang essential for tsunami run-up and inundation simulations. Tsunami inundation scenarios critical to risk analysis and mitigation could then be developed using this DEBM for various earthquake scenarios, as presented in this paper for the 2004 Indian Ocean Tsunami.

scholarly journals New elevation data triple estimates of global vulnerability to sea-level rise and coastal flooding

2019 ◽  
Vol 10 (1) ◽  
Author(s):  
Scott A. Kulp ◽  
Benjamin H. Strauss
Keyword(s):  
Sea Level Rise ◽  
Sea Level ◽  
High Tide ◽  
Water Levels ◽  
Low Carbon ◽  
Digital Elevation ◽  
Elevation Data ◽  
Global Mean Sea Level ◽  
Elevation Model ◽  
Global Mean

Abstract Most estimates of global mean sea-level rise this century fall below 2 m. This quantity is comparable to the positive vertical bias of the principle digital elevation model (DEM) used to assess global and national population exposures to extreme coastal water levels, NASA’s SRTM. CoastalDEM is a new DEM utilizing neural networks to reduce SRTM error. Here we show – employing CoastalDEM—that 190 M people (150–250 M, 90% CI) currently occupy global land below projected high tide lines for 2100 under low carbon emissions, up from 110 M today, for a median increase of 80 M. These figures triple SRTM-based values. Under high emissions, CoastalDEM indicates up to 630 M people live on land below projected annual flood levels for 2100, and up to 340 M for mid-century, versus roughly 250 M at present. We estimate one billion people now occupy land less than 10 m above current high tide lines, including 230 M below 1 m.

scholarly journals Volume change of Jakobshavn Isbræ, West Greenland: 1985–1997–2007

2010 ◽  
Vol 56 (198) ◽  
pp. 635-646 ◽  
Author(s):  
Roman J. Motyka ◽  
Mark Fahnestock ◽  
Martin Truffer
Keyword(s):  
Sea Level ◽  
Climate Forcing ◽  
Similar Magnitude ◽  
Specific Mass ◽  
Aerial Photos ◽  
West Greenland ◽  
Digital Elevation ◽  
Speed Up ◽  
Elevation Model ◽  
Fast Flow

AbstractFollowing three decades of relative stability, Jakobshavn Isbræ, West Greenland, underwent dramatic thinning, retreat and speed-up starting in 1998. To assess the amount of ice loss, we analyzed 1985 aerial photos and derived a 40 m grid digital elevation model (DEM). We also obtained a 2007 40 m grid SPOT DEM covering the same region. Comparison of the two DEMs over an area of ∼4000 km2 revealed a total ice loss of 160 ± 4 km3, with 107 ± 0.2 km3 in grounded regions (0.27 mm eustatic sea-level rise) and 53 ± 4 km3 from the disintegration of the floating tongue. Comparison of the DEMs with 1997 NASA Airborne Topographic Mapper data indicates that this ice loss essentially occurred after 1997, with +0.7 ± 5.6 km3 between 1985 and 1997 and −160 ± 7 km3 between 1997 and 2007. The latter is equivalent to an average specific mass balance of −3.7 ± 0.2 m a−1 over the study area. Previously reported thickening of the main glacier during the early 1990s was accompanied by similar-magnitude thinning outside the areas of fast flow, indicating that the land-based ice continued reacting to longer-term climate forcing.

scholarly journals Impact of sea level rise and shoreline changes in the tropical island ecosystem of Andaman and Nicobar region, India

2021 ◽  
Author(s):  
mageswaran thangaraj ◽  
Sachithanandam V ◽  
Sridhar R ◽  
Manik Mahapatra ◽  
R Purvaja ◽  
...  
Keyword(s):  
Remote Sensing ◽  
Sea Level Rise ◽  
Sea Level ◽  
Remote Sensing Data ◽  
Data Sets ◽  
Andaman Island ◽  
Shoreline Changes ◽  
Digital Elevation ◽  
Analysis System ◽  
Elevation Model

Abstract We report here a four decades of shoreline changes and possible sea level rise (SLR) impact on landuse/landcover (LULC) in Little Andaman Island by using remote sensing (RS) and GIS techniques. A total of six remote sensing data sets covering years between 1976 and 2018 were used to understand the shoreline changes. Moreover, a Digital Shoreline Analysis System (DSAS) was used to estimate short- and long- term shoreline changes from ArcGIS environment. Besides, the Island vulnerability due to SLR was studied through using digital elevation model (DEM). As a result of Sumatra earthquake (2004), the results were showed a significant variation in shorline upliftment and subsidence. The land subsidence was noticed in the range of 1042-3077 ha with sea level rise between 1 and 5 m. Hence, we conclude that Little Andaman Island is vulnerable to SLR and overwhelm low elvation coastal zone.

scholarly journals EVALUATION DIGITAL ELEVATION MODEL GENERATED BY SYNTHETIC APERTURE RADAR DATA

2016 ◽  
Vol XLI-B1 ◽  
pp. 57-62
Author(s):  
H. B. Makineci ◽  
H. Karabörk
Keyword(s):  
Remote Sensing ◽  
Digital Elevation Model ◽  
Interpolation Method ◽  
Digital Elevation Models ◽  
European Space Agency ◽  
Mountain Area ◽  
Synthetic Aperture Radar Data ◽  
Radar Images ◽  
Digital Elevation ◽  
Elevation Model

Digital elevation model, showing the physical and topographical situation of the earth, is defined a tree-dimensional digital model obtained from the elevation of the surface by using of selected an appropriate interpolation method. DEMs are used in many areas such as management of natural resources, engineering and infrastructure projects, disaster and risk analysis, archaeology, security, aviation, forestry, energy, topographic mapping, landslide and flood analysis, Geographic Information Systems (GIS). Digital elevation models, which are the fundamental components of cartography, is calculated by many methods. Digital elevation models can be obtained terrestrial methods or data obtained by digitization of maps by processing the digital platform in general. Today, Digital elevation model data is generated by the processing of stereo optical satellite images, radar images (radargrammetry, interferometry) and lidar data using remote sensing and photogrammetric techniques with the help of improving technology. <br><br> One of the fundamental components of remote sensing radar technology is very advanced nowadays. In response to this progress it began to be used more frequently in various fields. Determining the shape of topography and creating digital elevation model comes the beginning topics of these areas. <br><br> It is aimed in this work , the differences of evaluation of quality between Sentinel-1A SAR image ,which is sent by European Space Agency ESA and Interferometry Wide Swath imaging mode and C band type , and DTED-2 (Digital Terrain Elevation Data) and application between them. The application includes RMS static method for detecting precision of data. Results show us to variance of points make a high decrease from mountain area to plane area.

scholarly journals Flooding Model as the Analysis of the Sea Level Increase as a Result of Global Warming in Coastal Area in Lampung

2017 ◽  
Vol 9 (2) ◽  
pp. 109
Author(s):  
Agung Kurniawan
Keyword(s):  
Global Warming ◽  
Sea Level ◽  
Shuttle Radar Topography Mission ◽  
Sea Surface ◽  
Gis Mapping ◽  
Flood Inundation ◽  
Mapping Software ◽  
Level Increase ◽  
Digital Elevation ◽  
Elevation Model

The melting of ice layers, as a direct impact on global warming, is indicated from a lesser thickness of ice layers is specifically causing an increase on the sea level. Lampung, as a province that has an ecosistem of regional coast, can be estimated to submerge. Flood modelling can be done to know the estimated flood range. The model of the flooded region is taken from Shuttle Radar Topography Mission(SRTM) data, which is nomalized to get the visualisation of Digital Elevation Model (DEM). The purpose of this research is to know the estimated region of provincial coast of Lampung that is going to be flooded because of the raising of sea surface. This research uses flood inundation technique that uses one of the GIS mapping software. The result can be used as consideration to achieve policy in the building of regional coast. The regions that are flooded based on the scenario of the raising of two and three meter surface sea level are East Lampung Regency, West Lampung Regency, South Lampung Regency, Tanggamus Regency, Pesawaran Regency, and Bandar Lampung.

Sign in / Sign up

Export Citation Format

Share Document