scholarly journals Low-level jets and above-canopy drainage as causes of turbulent exchange in the nocturnal boundary layer

2014 ◽  
Vol 11 (16) ◽  
pp. 4507-4519 ◽  
Author(s):  
T. S. El-Madany ◽  
H. F. Duarte ◽  
D. J. Durden ◽  
B. Paas ◽  
M. J. Deventer ◽  
...  
Keyword(s):  
Carbon Dioxide ◽  
Wind Speed ◽  
Eddy Covariance ◽  
Latent Heat ◽  
Heat Fluxes ◽  
Vertical Wind ◽  
Sensible Heat ◽  
Intermittent Turbulence ◽  
Low Level Jets ◽  
Vertical Wind Velocity

Abstract. Sodar (SOund Detection And Ranging), eddy-covariance, and tower profile measurements of wind speed and carbon dioxide were performed during 17 consecutive nights in complex terrain in northern Taiwan. The scope of the study was to identify the causes for intermittent turbulence events and to analyze their importance in nocturnal atmosphere–biosphere exchange as quantified with eddy-covariance measurements. If intermittency occurs frequently at a measurement site, then this process needs to be quantified in order to achieve reliable values for ecosystem characteristics such as net ecosystem exchange or net primary production. Fourteen events of intermittent turbulence were identified and classified into above-canopy drainage flows (ACDFs) and low-level jets (LLJs) according to the height of the wind speed maximum. Intermittent turbulence periods lasted between 30 and 110 min. Towards the end of LLJ or ACDF events, positive vertical wind velocities and, in some cases, upslope flows occurred, counteracting the general flow regime at nighttime. The observations suggest that the LLJs and ACDFs penetrate deep into the cold air pool in the valley, where they experience strong buoyancy due to density differences, resulting in either upslope flows or upward vertical winds. Turbulence was found to be stronger and better developed during LLJs and ACDFs, with eddy-covariance data presenting higher quality. This was particularly indicated by spectral analysis of the vertical wind velocity and the steady-state test for the time series of the vertical wind velocity in combination with the horizontal wind component, the temperature, and carbon dioxide. Significantly higher fluxes of sensible heat, latent heat, and shear stress occurred during these periods. During LLJs and ACDFs, fluxes of sensible heat, latent heat, and CO2 were mostly one-directional. For example, exclusively negative sensible heat fluxes occurred while intermittent turbulence was present. Latent heat fluxes were mostly positive during LLJs and ACDFs, with a median value of 34 W m−2, while outside these periods the median was 2 W m−2. In conclusion, intermittent turbulence periods exhibit a strong impact on nocturnal energy and mass fluxes.

scholarly journals Low-level jets and above canopy drainage as causes for turbulent exchange in the nocturnal boundary layer

2014 ◽  
Vol 11 (3) ◽  
pp. 4695-4727
Author(s):  
T.-S. El-Madany ◽  
H. F. Duarte ◽  
D. J. Durden ◽  
B. Paas ◽  
M. J. Deventer ◽  
...  
Keyword(s):  
Wind Speed ◽  
Eddy Covariance ◽  
Latent Heat ◽  
Heat Fluxes ◽  
Strong Impact ◽  
Sensible Heat ◽  
Intermittent Turbulence ◽  
Low Level ◽  
Wind Speed Maximum ◽  
Low Level Jets

Abstract. SODAR (SOund Detection And Ranging), eddy-covariance, and tower profile measurements of wind speed and carbon dioxide were performed during 17 consecutive nights in complex terrain in northern Taiwan. The scope of the study was to identify the causes for intermittent turbulence events and to analyse their importance in nocturnal atmosphere–biosphere exchange as quantified with eddy-covariance measurements. If intermittency occurs frequently at a measurement site this process needs to be quantified in order to achieve reliable values for ecosystem characteristics such as net ecosystem exchange or net primary production. Fourteen events of intermittent turbulence were identified and classified into above canopy drainage flows (ACDF) and low-level jets (LLJ) according to the height of the wind speed maximum. Intermittent turbulence periods lasted between 30 min and 110 min. Towards the end of LLJ or ACDF events, positive vertical wind velocities and, in some cases upslope flows occurred, counteracting the general flow regime at night time. The observations suggest that the LLJ and ACDF penetrate deep into the cold air pool in the valley, where they experience strong buoyancy due to density differences, resulting in either upslope flows or upward vertical winds. Turbulence was found to be stronger and better developed during LLJs and ACDFs, with eddy-covariance data presenting higher quality. This was particularly indicated by spectral analysis and stationary tests. Significantly higher fluxes of sensible heat, latent heat and shear stress occurred during these periods. During LLJ and ACDF, fluxes of sensible heat, latent heat, and CO2 were mostly one-directional. For example, exclusively negative sensible heat fluxes occurred while intermittent turbulence was present. Latent heat fluxes were mostly positive during LLJ and ACDF with a median value of 34 W m−2, while outside these periods the median was 2 W m−2. In conclusion, intermittent turbulence periods exhibit a strong impact on nocturnal energy and mass fluxes.

scholarly journals Fetch Effect on Flux-Variance Estimations of Sensible and Latent Heat Fluxes of Camellia Sinensis

Atmosphere ◽  
2019 ◽  
Vol 10 (6) ◽  
pp. 299
Author(s):  
Noman Ali Buttar ◽  
Hu Yongguang ◽  
Josef Tanny ◽  
M Waqar Akram ◽  
Abdul Shabbir
Keyword(s):  
Heat Flux ◽  
Eddy Covariance ◽  
Latent Heat ◽  
Sensible Heat Flux ◽  
Soil Heat Flux ◽  
Surface Fluxes ◽  
Heat Fluxes ◽  
Effect Of Temperature ◽  
Sensible Heat ◽  
Fine Wire

Precise estimation of surface-atmosphere exchange is a major challenge in micrometeorology. Previous literature presented the eddy covariance (EC) as the most reliable method for the measurements of such fluxes. Nevertheless, the EC technique is quite expensive and complex, hence other simpler methods are sought. One of these methods is Flux-Variance (FV). The FV method estimates sensible heat flux (H) using high frequency (~10Hz) air temperature measurements by a fine wire thermocouple. Additional measurements of net radiation (Rn) and soil heat flux (G) allow the derivation of latent heat flux (LE) as the residual of the energy balance equation. In this study, the Flux Variance method was investigated, and the results were compared against eddy covariance measurements. The specific goal of the present study was to assess the performance of the FV method for the estimation of surface fluxes along a variable fetch. Experiment was carried out in a tea garden; an EC system measured latent and sensible heat fluxes and five fine-wire thermocouples were installed towards the wind dominant direction at different distances (fetch) of TC1 = 170 m, TC2 = 165 m, TC3 = 160 m, TC4 = 155 m and TC5 = 150 m from the field edge. Footprint analysis was employed to examine the effect of temperature measurement position on the ratio between 90% footprint and measurement height. Results showed a good agreement between FV and EC measurements of sensible heat flux, with all regression coefficients (R2) larger than 0.6; the sensor at 170 m (TC1), nearest to the EC system, had highest R2 = 0.86 and lowest root mean square error (RMSE = 25 Wm−2). The estimation of LE at TC1 was also in best agreement with eddy covariance, with the highest R2 = 0.90. The FV similarity constant varied along the fetch within the range 2.2–2.4.

Determining Meaningful Differences for SMACEX Eddy Covariance Measurements

2005 ◽  
Vol 6 (6) ◽  
pp. 805-811 ◽  
Author(s):  
D. W. Meek ◽  
J. H. Prueger ◽  
W. P. Kustas ◽  
J. L. Hatfield
Keyword(s):  
Standard Deviation ◽  
Eddy Covariance ◽  
Wind Velocity ◽  
Standard Error ◽  
Friction Velocity ◽  
Vertical Wind ◽  
Sensible Heat ◽  
Significant Difference ◽  
Multiple Comparison Procedures ◽  
Vertical Wind Velocity

Abstract Two eddy covariance instrument comparison studies were conducted before and after the Soil Moisture–Atmosphere Coupling Experiment (SMACEX) field campaign to 1) determine if observations from multiple sensors were equivalent for the measured variables over a uniform surface and to 2) determine a least significant difference (LSD) value for each variable to discriminate between daily and hourly differences in latent and sensible heat and carbon dioxide fluxes, friction velocity, and standard deviation of the vertical wind velocity from eddy covariance instruments placed in different locations within the study area. The studies were conducted in early June over an alfalfa field and in mid-September over a short grass field. Several statistical exploratory, graphical, and multiple-comparison procedures were used to evaluate each daily variable. Daily total or average data were used to estimate a pooled standard error and corresponding LSD values at the P = 0.05 and P = 0.01 levels using univariate procedures. There were no significant sensor differences in any of the daily measurements for either intercomparison period. Hourly averaged data were used to estimate a pooled standard error and corresponding LSD values at the P = 0.05 and P = 0.01 levels using mixed model procedures. Sensor differences for pre- and post-intercomparisons were minimal for hourly and daily values of CO2, water vapor, sensible heat, friction velocity, and standard deviation for vertical wind velocity. Computed LSD values were used to determine significant daily differences and threshold values for the variables monitored during the SMACEX campaign.

Wind and Temperature Oscillations Generated by Wave–Turbulence Interactions in the Stably Stratified Boundary Layer

2015 ◽  
Vol 72 (4) ◽  
pp. 1484-1503 ◽  
Author(s):  
Jielun Sun ◽  
Larry Mahrt ◽  
Carmen Nappo ◽  
Donald H. Lenschow
Keyword(s):  
Boundary Layer ◽  
Wind Speed ◽  
Turbulent Mixing ◽  
Internal Gravity Waves ◽  
Heat Fluxes ◽  
Shear Instability ◽  
Forced Oscillations ◽  
Sensible Heat ◽  
Intermittent Turbulence ◽  
Stable Atmospheric Boundary Layer

Abstract The authors investigate atmospheric internal gravity waves (IGWs): their generation and induction of global intermittent turbulence in the nocturnal stable atmospheric boundary layer based on the new concept of turbulence generation discussed in a prior paper by Sun et al. The IGWs are generated by air lifted by convergence forced by the colliding background flow and cold currents near the ground. The buoyancy-forced IGWs enhance wind speed at the wind speed wave crests such that the bulk shear instability generates large coherent eddies, which augment local turbulent mixing and vertically redistribute momentum and heat. The periodically enhanced turbulent mixing, in turn, modifies the air temperature and flow oscillations of the original IGWs. These turbulence-forced oscillations (TFOs) resemble waves and coherently transport momentum and sensible heat. The observed momentum and sensible heat fluxes at the IGW frequency, which are due to either the buoyancy-forced IGWs themselves or the TFOs, are larger than turbulent fluxes near the surface. The IGWs enhance not only the bulk shear at the wave crests, but also local shear over the wind speed troughs of the surface IGWs. Temporal and spatial variations of turbulent mixing as a result of this wave-induced turbulent mixing change the mean airflow and the shape of the IGWs.

scholarly journals How representative are FLUXNET measurements of surface fluxes during temperature extremes?

2018 ◽  
Author(s):  
Sophie V. J. van der Horst ◽  
Andrew J. Pitman ◽  
Martin G. De Kauwe ◽  
Anna Ukkola ◽  
Gab Abramowitz ◽  
...  
Keyword(s):  
Temperature Distribution ◽  
Latent Heat ◽  
Net Ecosystem Exchange ◽  
The United States ◽  
Fair Use ◽  
Heat Fluxes ◽  
Temperature Extremes ◽  
Measured Temperature ◽  
Sensible Heat ◽  
Lower Tail

Abstract. In response to a warming climate, temperature extremes are changing in many regions of the world. Therefore, understanding how the fluxes of sensible heat, latent heat and net ecosystem exchange respond and contribute to these changes is important. We examined 216 sites from the open access Tier 1 FLUXNET2015 and Free-Fair-Use La Thuile datasets, focussing only on observed (non-gap filled) data periods. We examined the availability of sensible heat, latent heat and net ecosystem exchange observations coincident in time with measured temperature for all temperatures, and separately for the upper and lower tail of the temperature distribution and expressed this availability as a measurement ratio. We showed that the measurement ratios for both sensible and latent heat fluxes are generally lower (0.79 and 0.73 respectively) than for temperature, and the measurement ratio of net ecosystem exchange measurements are appreciably lower (0.42). However, sites do exist with a high proportion of measured sensible and latent heat fluxes, mostly over the United States, Europe and Australia. Few sites have a high proportion of measured fluxes at the lower tail of the temperature distribution over very cold regions (e.g. Alaska, Russia) and at the upper tail in many warm regions (e.g. Central America and the majority of the Mediterranean region), and many of the world’s coldest and hottest regions are not represented in the freely available FLUXNET data at all (e.g. India, the Gulf States, Greenland and Antarctica). However, some sites do provide measured fluxes at extreme temperatures suggesting an opportunity for the FLUXNET community to share strategies to increase measurement availability at the tails of the temperature distribution. We also highlight a wide discrepancy between the measurement ratios across FLUXNET sites that is not related to the actual temperature or rainfall regimes at the site, which we cannot explain. Our analysis provides guidance to help select eddy covariance sites for researchers interested in exploring responses to temperature extremes.

scholarly journals Comparison of turbulent structures and energy fluxes over exposed and debris-covered glacier ice

2020 ◽  
Vol 66 (258) ◽  
pp. 543-555 ◽  
Author(s):  
Lindsey Nicholson ◽  
Ivana Stiperski
Keyword(s):  
Heat Flux ◽  
Latent Heat ◽  
Similarity Theory ◽  
Sensible Heat Flux ◽  
Heat Fluxes ◽  
Temperature Fields ◽  
Sensible Heat ◽  
Energy Fluxes ◽  
Glacier Surface ◽  
Debris Cover

AbstractWe present the first direct comparison of turbulence conditions measured simultaneously over exposed ice and a 0.08 m thick supraglacial debris cover on Suldenferner, a small glacier in the Italian Alps. Surface roughness, sensible heat fluxes (~20–50 W m−2), latent heat fluxes (~2–10 W m−2), topology and scale of turbulence are similar over both glacier surface types during katabatic and synoptically disturbed conditions. Exceptions are sunny days when buoyant convection becomes significant over debris-covered ice (sensible heat flux ~ −100 W m−2; latent heat flux ~ −30 W m−2) and prevailing katabatic conditions are rapidly broken down even over this thin debris cover. The similarity in turbulent properties implies that both surface types can be treated the same in terms of boundary layer similarity theory. The differences in turbulence between the two surface types on this glacier are dominated by the radiative and thermal contrasts, thus during sunny days debris cover alters both the local surface turbulent energy fluxes and the glacier component of valley circulation. These variations under different flow conditions should be accounted for when distributing temperature fields for modeling applications over partially debris-covered glaciers.

scholarly journals Ecosystem model optimization using in situ flux observations: benefit of Monte Carlo versus variational schemes and analyses of the year-to-year model performances

2014 ◽  
Vol 11 (24) ◽  
pp. 7137-7158 ◽  
Author(s):  
D. Santaren ◽  
P. Peylin ◽  
C. Bacour ◽  
P. Ciais ◽  
B. Longdoz
Keyword(s):  
Monte Carlo ◽  
Eddy Covariance ◽  
Latent Heat ◽  
Environmental Changes ◽  
Beech Forest ◽  
Heat Fluxes ◽  
Surface Model ◽  
Forest Site ◽  
Weather Regimes ◽  
Variational Scheme

Abstract. Terrestrial ecosystem models can provide major insights into the responses of Earth's ecosystems to environmental changes and rising levels of atmospheric CO2. To achieve this goal, biosphere models need mechanistic formulations of the processes that drive the ecosystem functioning from diurnal to decadal timescales. However, the subsequent complexity of model equations is associated with unknown or poorly calibrated parameters that limit the accuracy of long-term simulations of carbon or water fluxes and their interannual variations. In this study, we develop a data assimilation framework to constrain the parameters of a mechanistic land surface model (ORCHIDEE) with eddy-covariance observations of CO2 and latent heat fluxes made during the years 2001–2004 at the temperate beech forest site of Hesse, in eastern France. As a first technical issue, we show that for a complex process-based model such as ORCHIDEE with many (28) parameters to be retrieved, a Monte Carlo approach (genetic algorithm, GA) provides more reliable optimal parameter values than a gradient-based minimization algorithm (variational scheme). The GA allows the global minimum to be found more efficiently, whilst the variational scheme often provides values relative to local minima. The ORCHIDEE model is then optimized for each year, and for the whole 2001–2004 period. We first find that a reduced (<10) set of parameters can be tightly constrained by the eddy-covariance observations, with a typical error reduction of 90%. We then show that including contrasted weather regimes (dry in 2003 and wet in 2002) is necessary to optimize a few specific parameters (like the temperature dependence of the photosynthetic activity). Furthermore, we find that parameters inverted from 4 years of flux measurements are successful at enhancing the model fit to the data on several timescales (from monthly to interannual), resulting in a typical modeling efficiency of 92% over the 2001–2004 period (Nash–Sutcliffe coefficient). This suggests that ORCHIDEE is able robustly to predict, after optimization, the fluxes of CO2 and the latent heat of a specific temperate beech forest (Hesse site). Finally, it is shown that using only 1 year of data does not produce robust enough optimized parameter sets in order to simulate properly the year-to-year flux variability. This emphasizes the need to assimilate data over several years, including contrasted weather regimes, to improve the simulated flux interannual variability.

Sign in / Sign up

Export Citation Format

Share Document