scholarly journals TIDE GAUGE AND SATELLITE ALTIMETRY DATA FOR POSSIBLE VERTICAL LAND MOTION DETECTION IN SOUTH EAST BOHOL TRENCH AND FAULT

Author(s):  
R. Reyes ◽  
D. Noveloso ◽  
A. Rediang ◽  
M. Passaro ◽  
D. Bringas ◽  
...  

Abstract. Coupled with the occurrence of regional/local sea level rise on urbanized coastal cities is the possibility of land subsidence that contaminates the measurement by the tide gauge (TG) sensors. Another technology that could possibly check the in-situ data from tide gauge is satellite altimetry. The sea surface height (SSH) measured from satellite altimeter is compared with the observed tide gauge sea level (TGSL) to detect vertical land motion (VLM). This study used satellite altimeter retracked products near the TG Stations in Tagbilaran, Bohol; Dumaguete, Negros Oriental; and Mambajao, Camiguin located in the vicinity of the South East Bohol Trench and Fault (SEBTF).Based on the results, the TG site in Tagbilaran is undergoing land subsidence. The rate of VLM is around 5 mm/year from 2009 to 2017. The same trend was manifested in the GNSS observed data in the PHIVOLCS monitoring station in Tagbilaran and the geodetic levelling done in the area. After the October 15, 2013 earthquake in Bohol, downward trends of around 27 mm/year and 17 mm/year were observed from GNSS measurements and SSH-TGSL difference respectively. These different rates may be due to the distance between the two sensors. The comparison between SSH and TGSL in Dumaguete showed small difference with a VLM rate of 1.8 mm/year. The difference in SSH-TGSL in Mambajao is quite large with a downward rate of 9.4 mm/year. This result needs to be further investigated for TG or TGBM instability or monitored for a possibility of land uplift.

2021 ◽  
Author(s):  
Milaa Murshan ◽  
Balaji Devaraju ◽  
Nagarajan Balasubramanian ◽  
Onkar Dikshit

<p>Satellite altimetry provides measurements of sea surface height of centimeter-level accuracy over open oceans. However, its accuracy reduces when approaching the coastal areas and over land regions. Despite this downside, altimetric measurements are still applied successfully in these areas through altimeter retracking processes. This study aims to calibrate and validate retracted sea level data of Envisat, ERS-2, Topex/Poseidon, Jason-1, 2, SARAL/AltiKa, Cryosat-2 altimetric missions near the Indian coastline. We assessed the reliability, quality, and performance of these missions by comparing eight tide gauge (TG) stations along the Indian coast. These are Okha, Mumbai, Karwar, and Cochin stations in the Arabian Sea, and Nagapattinam, Chennai, Visakhapatnam, and Paradip in the Bay of Bengal. To compare the satellite altimetry and TG sea level time series, both datasets are transformed to the same reference datum. Before the calculation of the bias between the altimetry and TG sea level time series, TG data are corrected for Inverted Barometer (IB) and Dynamic Atmospheric Correction (DAC). Since there are no prior VLM measurements in our study area, VLM is calculated from TG records using the same procedure as in the Technical Report NOS organization CO-OPS 065. </p><p>Keywords— Tide gauge, Sea level, North Indian ocean, satellite altimetry, Vertical land motion</p>


2020 ◽  
Author(s):  
Muharrem Hilmi Erkoç ◽  
Uğur Doğan ◽  
Seda Özarpacı ◽  
Hasan Yildiz ◽  
Erdinç Sezen

<p>This study aims to estimate vertical land motion (VLM) at tide gauges (TG), located in the Mediterranean, Aegean and the Marmara Sea coasts of Turkey, from differences of multimission satellite altimetry and TG sea level time series. Initially, relative sea level trends are estimated at 7 tide gauges stations operated by the Turkish General Directorate of Mapping over the period 2001-2019. Subsequently, absolute sea level trends independent from VLM are computed from multimission satellite altimetry data over the same period. We have computed estimates of linear trends of difference time series between altimetry and tide gauge sea level after removing seasonal signals by harmonic analysis from each time series to estimate the vertical land motion (VLM) at tide gauges. Traditional way of VLM determination at tide gauges is to use GPS@TG or preferably CGPS@TG data. We therefore, processed these GPS data, collected over the years by several TG-GPS campaigns and by continuous GPS stations close to the TG processed by GAMIT/GLOBK software. Subsequently, the GPS and CGPS vertical coordinate time series are used to estimate VLM. These two different VLM estimates, one from GPS and CGPS coordinate time series and other from altimetry-TG sea level time series differences are compared.</p><p> </p><p><strong>Keywords: Vertical land motion, Sea Level Changes, Tide gauge, Satellite altimetry, GPS, CGPS </strong></p>


2021 ◽  
Author(s):  
Fabio Mangini ◽  
Antonio Bonaduce ◽  
Léon Chafik ◽  
Laurent Bertino

<p>Satellite altimetry measurements, complemented by in-situ records, have made a fundamental contribution to the understanding of global sea level variability for almost 30 years. Due to land contamination, it performs best over the open ocean. However, over the years, there has been a significant effort to improve the altimetry products in coastal regions. Indeed, altimetry observations could be fruitfully used in the coastal zone to complement the existing tide gauge network which, despite its relevance, does not represent the entire coast. Given the important role of coastal altimetry in oceanography, we have recently decided to check the quality of a new coastal altimetry dataset, ALES, along the coast of Norway. The Norwegian coast is well covered by tide gauges and, therefore, particularly suitable to validate a coastal altimetry dataset. Preliminary results show a good agreement between in-situ and remote sensing sea-level signals in terms of linear trend, seasonal cycle and inter-annual variability. For example, the linear correlation coefficient between the inter-annual sea level variability from altimetry and tide gauges exceeds 0.8. Likewise, the root mean square difference between the two is less than 2 cm at most tide gauge locations. A comparison with Breili et al. (2017) shows that ALES performs better than the standard satellite altimetry products at estimating sea level trends along the coast of Norway. Notably, in the Lofoten region, the difference between the sea level trends computed using ALES and the tide gauges range between 0.0 to 0.7 mm/year, compared to circa 1 to 3 mm/year found by Breili et al. (2017). These preliminary results go in the direction of obtaining an accurate characterization of coastal sea-level at the high latitudes based on coastal altimetry records, which can represent a valuable source of information to reconstruct coastal sea-level signals in areas where in-situ data are missing or inaccurate.</p>


2021 ◽  
Vol 15 (4) ◽  
pp. 45-58
Author(s):  
Katarzyna Pajak ◽  
Kamil Kowalczyk ◽  
Jānis Kaminskis ◽  
Magdalena Idzikowska

Tide gauge observations provide sea level relative to the Earth’s crust, while satellite altimetry measures sea level variations relative to the centre of the Earth’s mass. Local vertical land motion can be a significant contribution to the measured sea level change.Satellite altimetry was traditionally used to study the open ocean, but this technology is now being used over inland seas too.The difference of both observations can be used to estimate vertical crustal movement velocities along the sea coast. In this paper, vertical crustal movement velocities were investigated at tide gauge sites along the Adriatic Sea coast by analyzing differences between Tide Gauge (TG) and Satellite Altimetry (SA) observations. Furthermore, the estimated vertical motion rates were compared with those from nearby GNSS measurements.The study determines the practical relationships between these vertical crustal movements and those determined from unrelated data acquired from the neighbouring GNSS stations. The results show general consistence with the present geodynamics in the Adriatic Sea coastal zone.


2020 ◽  
Vol 12 (21) ◽  
pp. 3543
Author(s):  
Marijan Grgić ◽  
Josip Bender ◽  
Tomislav Bašić

Different space-borne geodetic observation methods combined with in-situ measurements enable resolving the single-point vertical land motion (VLM) and/or the VLM of an area. Continuous Global Navigation Satellite System (GNSS) measurements can solely provide very precise VLM trends at specific sites. VLM area monitoring can be performed by Interferometric Synthetic Aperture Radar (InSAR) technology in combination with the GNSS in-situ data. In coastal zones, an effective VLM estimation at tide gauge sites can additionally be derived by comparing the relative sea-level trends computed from tide gauge measurements that are related to the land to which the tide gauges are attached, and absolute trends derived from the radar satellite altimeter data that are independent of the VLM. This study presents the conjoint analysis of VLM of the Dubrovnik area (Croatia) derived from the European Space Agency’s Sentinel-1 InSAR data available from 2014 onwards, continuous GNSS observations at Dubrovnik site obtained from 2000, and differences of the sea-level change obtained from all available satellite altimeter missions for the Dubrovnik area and tide gauge measurements in Dubrovnik from 1992 onwards. The computed VLM estimates for the overlapping period of three observation methods, i.e., from GNSS observations, sea-level differences, and Sentinel-1 InSAR data, are −1.93±0.38 mm/yr, −2.04±0.22 mm/yr, and −2.24±0.46 mm/yr, respectively.


2020 ◽  
Vol 14 (3) ◽  
pp. 361-378
Author(s):  
V. B. Mendes ◽  
S. M. Barbosa ◽  
D. Carinhas

AbstractIn this study, we estimate vertical land motion for 35 stations primarily located along the coastline of Portugal and Spain, using GPS time series with at least eight years of observations. Based on this set of GPS stations, our results show that vertical land motion along the Iberian coastline is characterized, in general, by a low to moderate subsidence, ranging from −2.2 mm yr−1 to 0.4 mm yr−1, partially explained by the glacial isostatic adjustment geophysical signal. The estimates of vertical land motion are subsequently applied in the analysis of tide gauge records and compared with geocentric estimates of sea level change. Geocentric sea level for the Iberian Atlantic coast determined from satellite altimetry for the last three decades has a mean of 2.5 ± 0.6 mm yr−1, with a significant range, as seen for a subset of grid points located in the vicinity of tide gauge stations, which present trends varying from 1.5 mm yr−1 to 3.2 mm yr−1. Relative sea level determined from tide gauges for this region shows a high degree of spatial variability, that can be partially explained not only by the difference in length and quality of the time series, but also for possible undocumented datum shifts, turning some trends unreliable. In general, tide gauges corrected for vertical land motion produce smaller trends than satellite altimetry. Tide gauge trends for the last three decades not corrected for vertical land motion range from 0.3 mm yr−1 to 5.0 mm yr−1 with a mean of 2.6 ± 1.4 mm yr−1, similar to that obtained from satellite altimetry. When corrected for vertical land motion, we observe a reduction of the mean to ∼1.9 ± 1.4 mm yr−1. Actions to improve our knowledge of vertical land motion using space geodesy, such as establishing stations in co-location with tide gauges, will contribute to better evaluate sea level change and its impacts on coastal regions.


2020 ◽  
Vol 8 (11) ◽  
pp. 949 ◽  
Author(s):  
Francesco De Biasio ◽  
Giorgio Baldin ◽  
Stefano Vignudelli

We propose a revisited approach to estimating sea level change trends based on the integration of two measuring systems: satellite altimetry and tide gauge (TG) time series of absolute and relative sea level height. Quantitative information on vertical crustal motion trends at six TG stations of the Adriatic Sea are derived by solving a constrained linear inverse problem. The results are verified against Global Positioning System (GPS) estimates at some locations. Constraints on the linear problem are represented by estimates of relative vertical land motion between TG couples. The solution of the linear inverse problem is valid as long as the same rates of absolute sea level rise are observed at the TG stations used to constrain the system. This requirement limits the applicability of the method with variable absolute sea level trends. The novelty of this study is that we tried to overcome such limitations, subtracting the absolute sea level change estimates observed by the altimeter from all relevant time series, but retaining the original short-term variability and associated errors. The vertical land motion (VLM) solution is compared to GPS estimates at three of the six TGs. The results show that there is reasonable agreement between the VLM rates derived from altimetry and TGs, and from GPS, considering the different periods used for the processing of VLM estimates from GPS. The solution found for the VLM rates is optimal in the least square sense, and no longer depends on the altimetric absolute sea level trend at the TGs. Values for the six TGs’ location in the Adriatic Sea during the period 1993–2018 vary from −1.41 ± 0.47 mm y−1 (National Research Council offshore oceanographic tower in Venice) to 0.93 ± 0.37 mm y−1 (Rovinj), while GPS solutions range from −1.59 ± 0.65 (Venice) to 0.10 ± 0.64 (Split) mm y−1. The absolute sea level rise, calculated as the sum of relative sea level change rate at the TGs and the VLM values estimated in this study, has a mean of 2.43 mm y−1 in the period 1974–2018 across the six TGs, a mean standard error of 0.80 mm y−1, and a sample dispersion of 0.18 mm y−1.


2019 ◽  
Vol 11 (7) ◽  
pp. 744 ◽  
Author(s):  
Martina Idžanović ◽  
Christian Gerlach ◽  
Kristian Breili ◽  
Ole Andersen

Present-day climate-change-related ice-melting induces elastic glacial isostatic adjustment (GIA) effects, while paleo-GIA effects describe the ongoing viscous response to the melting of late-Pleistocene ice sheets. The unloading initiated an uplift of the crust close to the centers of former ice sheets. Today, vertical land motion (VLM) rates in Fennoscandia reach values up to around 10 mm/year and are dominated by GIA. Uplift signals from GIA can be computed by solving the sea-level equation (SLE), S ˙ = N ˙ − U ˙ . All three quantities can also be determined from geodetic observations: relative sea-level variations ( S ˙ ) are observed by means of tide gauges, while rates of absolute sea-level change ( N ˙ ) can be observed by satellite altimetry; rates of VLM ( U ˙ ) can be determined by GPS (Global Positioning System). Based on the SLE, U ˙ can be derived by combining sea-surface measurements from satellite altimetry and relative sea-level records from tide gauges. In the present study, we have combined 7.5 years of CryoSat-2 satellite altimetry and tide-gauge data to estimate linear VLM rates at 20 tide gauges along the Norwegian coast. Thereby, we made use of monthly averaged tide-gauge data from PSMSL (Permanent Service for Mean Sea Level) and a high-frequency tide-gauge data set with 10-min sampling rate from NMA (Norwegian Mapping Authority). To validate our VLM estimates, we have compared them with the independent semi-empirical land-uplift model NKG2016LU_abs for the Nordic-Baltic region, which is based on GPS, levelling, and geodynamical modeling. Estimated VLM rates from 1 Hz CryoSat-2 and high-frequency tide-gauge data reflect well the amplitude of coastal VLM as provided by NKG2016LU_abs. We find a coastal average of 2.4 mm/year (average over all tide gauges), while NKG2016LU_abs suggests 2.8 mm/year; the spatial correlation is 0.58.


GeoHazards ◽  
2021 ◽  
Vol 2 (2) ◽  
pp. 80-100
Author(s):  
Phil J. Watson

The potential threats to the USA from current and projected sea level rise are significant, with profound environmental, social and economic consequences. This current study continues the refinement and improvement in analysis techniques for sea level research beyond the Fourth US National Climate Assessment (NCA4) report by incorporating further advancements in the time series analysis of long tide gauge records integrated with an improved vertical land motion (VLM) assessment. This analysis has also been synthesised with an updated regional assessment of satellite altimetry trends in the sea margins fringing the USA. Coastal margins more vulnerable to the threats posed by rising sea levels are those in which subsidence is prevalent, higher satellite altimetry trends are evident and higher ‘geocentric’ velocities in mean sea level are being observed. The evidence from this study highlights key spatial features emerging in 2020, which highlight the northern foreshore of the Gulf Coast and along the east coast of the USA south of the Chesapeake Bay region being more exposed to the range of factors exacerbating threats from sea level rise than other coastlines at present. The findings in this study complement and extend sea level research beyond NCA4 to 2020.


2009 ◽  
Vol 26 (3) ◽  
pp. 556-569 ◽  
Author(s):  
Ananda Pascual ◽  
Christine Boone ◽  
Gilles Larnicol ◽  
Pierre-Yves Le Traon

Abstract The timeliness of satellite altimeter measurements has a significant effect on their value for operational oceanography. In this paper, an Observing System Experiment (OSE) approach is used to assess the quality of real-time altimeter products, a key issue for robust monitoring and forecasting of the ocean state. In addition, the effect of two improved geophysical corrections and the number of missions that are combined in the altimeter products are also analyzed. The improved tidal and atmospheric corrections have a significant effect in coastal areas (0–100 km from the shore), and a comparison with tide gauge observations shows a slightly better agreement with the gridded delayed-time sea level anomalies (SLAs) with two altimeters [Jason-1 and European Remote Sensing Satellite-2 (ERS-2)/Envisat] using the new geophysical corrections (mean square differences in percent of tide gauge variance of 35.3%) than those with four missions [Jason-1, ERS/Envisat, Ocean Topography Experiment (TOPEX)/Poseidoninterlaced, and Geosat Follow-On] but using the old corrections (36.7%). In the deep ocean, however, the correction improvements have little influence. The performance of fast delivery products versus delayed-time data is compared using independent in situ data (tide gauge and drifter data). It clearly highlights the degradation of real-time SLA maps versus the delayed-time SLA maps: four altimeters are needed in real time to get the similar quality performance as two altimeters in delayed time (sea level error misfit around 36%, and zonal and meridional velocity estimation errors of 27% and 33%, respectively). This study proves that the continuous improvement of geophysical corrections is very important, and that it is essential to stay above a minimum threshold of four available altimetric missions to capture the main space and time oceanic scales in fast delivery products.


Sign in / Sign up

Export Citation Format

Share Document