scholarly journals Hybrid Carbon Dioxide Heat Pump for the Multifamily Residential Buildings in the Heat Supply System Based on CHP

2021 ◽  
pp. 91-98
Author(s):  
Mihail Sit ◽  
◽  
Anatoliy Juravliov ◽  
Keyword(s):  
Heat Exchanger ◽  
Heat Pump ◽  
Heat Supply ◽  
Single Phase ◽  
Control Valve ◽  
Heating System ◽  
Heat Pumps ◽  
Hydraulic Circuit ◽  
Heat Supply Systems ◽  
Supply Systems

The work is devoted to centralized heat supply systems based on CHP plants and the use with them heat pumps (HP) on carbon dioxide as refrigerant. Heat pumps are used in heat supply systems for buildings and use the heat of the outside air and, at the same time, the heat of the return network water (WWR) as a source of low-grade heat (LHP). The aim of the study is to develop a structural diagram of such a heat pump, where the outside air is heated by a heat exchanger installed in the return water line of the heating system, to develop a hydraulic circuit of a heat pump taking into account the law of regulation of the building heating system, to develop an algorithm for controlling the operating modes of the so-called balancing heat exchanger installed after gas cooler and internal heat exchanger of the heat pump. The most significant results were the hydraulic circuit of the heat pump, the aerodynamic circuit of the air supply path to the heat pump evaporator, the balancing heat exchanger control system, taking into account the requirement to ensure the operation of the control valve in a single-phase flow. The significance of the results obtained consisted in obtaining the dependences between the CO temperature graph and the parameters of the thermodynamic cycle of the heat pump, which ensured the operation of the control valve of the heat pump in a single-phase environment.

Design and Performance of Adsorptive Heat Pumps

2021 ◽  
pp. 223-250
Keyword(s):  
Heat Pump ◽  
Silica Gel ◽  
Heat Supply ◽  
Sodium Acetate ◽  
Energy Performance ◽  
Heat Pumps ◽  
Sodium Sulphate ◽  
Heat Supply Systems ◽  
And Performance ◽  
Supply Systems

The chapter is devoted to design and performance of adsorptive heat pumps. In the first sub-division, state-of-the-art of the adsorptive heat pumping is analyzed. It involves analysing operating principle of adsorptive heat pumps, comparing of the properties of adsorbents used, bed specifications, and operating conditions. Original construction of the adsorptive heat pump is designed by authors for independent heat supply systems or hot water supply of buildings and other structures for various purposes. The composites ‘silica gel – sodium sulphate' or ‘silica gel – sodium acetate' were used as adsorbents. Discharging was performed in a daytime, when heat pump supplied heating system with water warmed to 45 – 35°C. The regeneration mode proceeded at night from 0.00 to 8.00 a.m. Efficiency of suggested adsorptive heat pump is estimated by two methods: as ratio of adsorption heat to sum of desorption heat and external heat supplied to sorbent during its heating up to regeneration temperature (coefficient of performance of cycle) and as ratio of heat of adsorption to heat supplied by solar collector (net coefficient of performance). Suggested heat pump coefficients of energy performance of cycle are stated to be 2.084 when composite ‘silica gel – sodium sulphate' used and 2.021 when ‘silica gel – sodium acetate' used. Seasonal dependence of net coefficient energy performance for suggested adsorptive heat pump based on composites ‘silica gel – sodium sulphate' and ‘silica gel – sodium acetate' is revealed. Correlation of coefficients of energy performance of adsorptive heat pump and composite sorbents properties (sorption capacity and regeneration temperature) is stated. Insignificant decreasing of coefficients of energy performance when ‘silica gel – sodium acetate' used is explained by lower sorptive capacity as compared to ‘silica gel – sodium sulphate'. Suggested heat pump application perspectives are shown for heat supply systems to result from traditional energy sources independence and environmental advantages. Adsorptive heat pumps development challenges, major limitations for commercialization of adsorptive heat pumping, and requirements to ongoing innovations are analysed. The present chapter can be useful for energy efficient decentralized heat supply systems based on adsorptive heat pump unit.

Potential for the use of heat pumps for heat supply of metro stations

2018 ◽  
Vol 77 (4) ◽  
pp. 200-204 ◽  
Author(s):  
S. N. Naumenko ◽  
B. N. Minaev ◽  
I. A. Rebrov ◽  
G. B. Gusev
Keyword(s):  
Energy Saving ◽  
Heat Pump ◽  
Heat Supply ◽  
Heat Pumps ◽  
Operating Conditions ◽  
Hot Water ◽  
Energy Saving Technology ◽  
Heat Supply Systems ◽  
Metro Systems ◽  
Supply Systems

At present, specialists of foreign and domestic research organizations and industrial firms pay much attention to the use of steam compression heat pump plants (HPP) as an energy-saving technology. Modern compressor units allow receiving 3-4 kW for 1 kW of power consumed by HPP, and under certain conditions up to 5-6 kW of useful power. Today HPPs are most used in heat supply systems for residential and office buildings, especially in Scandinavia, Germany, Switzerland, USA, Japan, China. The paper discusses features of the operation of steam compressor heat pump plants as systems for improving energy efficiency with a description of the device of a heat pump plant; its main components are also listed. Review of the existing practice of introducing such systems in foreign countries is presented, including in Minsk - the Minsk metro, and in Russia - the Moscow Metro. The project, performed by specialists of JSC “VNIIZhT” and MIIT, is considered for the Moscow Metro (with reference to the heating systems of the Nagatinskaya and Pushkinskaya metro stations) for the use of dumping heat of ventilation shafts for heating and hot water supply, proposed by scientists of JSC “VNIIZhT” in 2012 within the framework of the exhibition of technical achievements. Authors presented information on the implementation of the pilot project at the station “Salar’yevo” (Moscow Metro) on the use of HPP in the heat and cooling supply system of the station for further comprehensive analysis of the effectiveness of the HPP application in the operating conditions of the metro. From the analysis of the data given in the work, it is concluded that metro systems are significant sources of low-potential heat, which can be used for the heat supply of stations and/or nearby urban sites by means of HPP. By now, there is a lot of experience (especially abroad) of the practical application of HPP in the heat supply systems of facilities. Nevertheless, for a reliable and comprehensive assessment of the feasibility and cost-effectiveness of projects using low-potential heat of metro systems as an energy-saving technology, a complex of studies is needed, including operational tests of currently implemented pilot projects.

Analyzing the Application of Heat Pump Units in Heat Supply Systems

Vestnik MEI ◽  
2018 ◽  
Vol 2 (2) ◽  
pp. 42-52
Author(s):  
Aleksandr Ya. Shelginsky ◽  
◽  
Igor V. Yakovlev ◽  
Keyword(s):  
Heat Pump ◽  
Heat Supply ◽  
Heat Supply Systems ◽  
Supply Systems

scholarly journals Heat Pump Cycle Efficiency for Heat Supply

2020 ◽  
pp. 136-142
Author(s):  
Mykola Bosiy ◽  
◽  
Olexandr Kuzyk ◽  
Keyword(s):  
Heat Pump ◽  
Heat Supply ◽  
Exergy Analysis ◽  
Conversion Factor ◽  
Working Fluid ◽  
Heating Systems ◽  
Energy And Exergy ◽  
Energy And Exergy Analysis ◽  
Heat Supply Systems ◽  
Supply Systems

The aim of the article is to analyze the literature and scientific publications on the effectiveness of the heat pump in heat supply systems and to study the efficiency of using the steam compression cycle of a heat pump in a heat supply system. Тo conduct energy and exergy analysis of heat pump efficiency indicators, the working fluid of which is freon R134a, when using natural waters as a source of low-potential thermal energy. The article analyzes the literature sources and scientific publications on the effectiveness of the heat pump in heat supply systems. The results of research of efficiency of application of the heat pump in systems of heat supply at use of natural waters as a source of low-potential thermal energy are presented. Energy and exergy analysis of heat pump efficiency indicators, the working fluid of which is R134a freon, was performed. The energy efficiency of the heat pump cycle was determined by the conversion factor of the heat pump. The thermodynamic efficiency of the heat pump in heat supply systems was evaluated using exergetic efficiency, which is one of the main indicators of the efficiency of heat pump processes and cycles. The calculation of energy indicators of the heat pump, such as: specific heat load in the evaporator and condenser, as well as the conversion factor of the heat pump. The calculation of exergetic efficiency for ambient temperature from +10 to -10 ºC. Thus, the energy and exergy analysis of the efficiency of the heat pump, the working fluid of which is Freon R134a with a conversion factor = 4.8. This indicates that the heat pump is a reliable, highly efficient, environmentally friendly source of energy for use in heating systems. A heat pump heating system will always consume less primary energy than traditional heating systems if natural water is used as a low-temperature heat source for the heat pump. The efficiency of the steam compression cycle of the heat pump largely depends on the temperature of low-potential heat sources. The use of HV in heating systems reduces greenhouse gas emissions compared to conventional types of heat supply, which is relevant to the ecological state of the environment.

scholarly journals The use of porous metals in the design of heat exchangers to increase the intensity of heat exchange

2020 ◽  
Vol 178 ◽  
pp. 01026
Author(s):  
Natalia Rydalina ◽  
Oleg Stepanov ◽  
Elena Antonova
Keyword(s):  
Heat Exchanger ◽  
Heat Exchange ◽  
Heat Exchangers ◽  
Heat Supply ◽  
Analytical Form ◽  
Test Facility ◽  
Porous Metals ◽  
Heat Supply Systems ◽  
Set Up ◽  
Supply Systems

Heat exchangers are widely used in heat supply systems. To increase the efficiency of heat supply systems, heat exchangers with porous metals are proposed to design. There was a test facility set up to study new types of heat exchangers. The countercurrent flow of heat carriers was activated in those heat exchangers. Freon moved through the heat exchanger pores, and water moved through the inner tubes. It should be noted that the porous materials in the heat exchangers differed in the coefficient of porosity. To be compared, one of the heat exchangers did not contain any porous material. The first test cycle proved the feasibility of using porous metals in heat exchange equipment. Afterwards, a simplified mathematical model of the heat exchanger was compiled. Such an analytical form makes a solution convenient for engineering calculations. Numerical calculations based on this model were compared with the experimental data. Heat transfer intensity of materials with different porosity was compared.

scholarly journals INCREASING THE RELIABILITY OF HEATING SYSTEMS

2020 ◽  
Vol 46 (4) ◽  
pp. 197-204
Author(s):  
R. A. Shershenov ◽  
A. Yu. Efimov ◽  
V. Yu. Shmakov
Keyword(s):  
Heat Supply ◽  
High Efficiency ◽  
Heat Supply System ◽  
Heating System ◽  
Supply System ◽  
The State ◽  
Additional Costs ◽  
Heat Supply Systems ◽  
Reliability Of Operation ◽  
Supply Systems

Objectives. The study was aimed at improving the reliability of heat supply systems. At present, this is one of the most relevant topics in the field of heat supply. The issue of reliability of heat supply is of great importance in terms of the safety of citizens and the state as a whole. Due to the severity of winter conditions and risk of hypothermia, heat supply security can be considered to be as critical as food security. Therefore, the reliability of heat supply systems becomes one of the most important aspects of the security of the state.Method. The study was carried out using the method of reservation of the heat supply system by looping.Result. In order to avoid the defrosting of the heat supply system and reduce additional costs, a redundancy scheme was proposed with one-way connection to the looped main pipelines, additionally looping the pipelines of the heat supply systems between two boiler rooms. The calculation of losses in the event of an emergency in the heating system was carried out.Conclusion. The most important problem requiring immediate solution is how to increase the reliability and redundancy of the heat supply system itself, in order to achieve minimal discomfort for consumers of heat energy at the time of failure of the source or transmission of the heat supply system. The proposed method for increasing the reliability of operation of heat supply systems is characterized by a high efficiency, since allows the number of idle hours and the total amount of short-received heat to be reduced. 

Sign in / Sign up

Export Citation Format

Share Document