RP-HPLC METHOD FOR SIMULTANEOUS ESTIMATION OF METFORMIN HCL AND CANAGLIFLOZIN IN PHARMACEUTICAL FORMULATION

INDIAN DRUGS ◽  
2021 ◽  
Vol 58 (06) ◽  
pp. 49-59
Author(s):  
Hemant Kumar T ◽  
◽  
Gowri Sankar D ◽  

A simple, specific, accurate, precise and stability-indicating RP-HPLC method was developed and validated for the simultaneous estimation of metformin HCl and canagliflozin in pharmaceutical formulation. The method was developed using the Altima C8 column (150 ×4.6 mm, 0.5 μm) with a mobile phase consisting of acetonitrile and 0.1 % orthophosphoric acid in water (62:38 %V/V) with a flow rate of 1 mL/min. Detection was carried out at 254 nm using a PDA detector. The retention time for metformin HCl and canagliflozin was found to be 2.282 and 3.339 min, respectively. The proposed method was validated for linearity, range, accuracy, precision, robustness, LOD and LOQ. Linearity was observed over a concentration range 15-225 μg/mL for metformin HCl (r2 =0.9995) and 5-40 μg/mL for canagliflozin (r2 =0.9988). The % RSD for intraday and interday precision was found to be 0.13 and 0.20 for metformin HCl and 0.18 and 0.20 for canagliflozin. The LOD and LOQ were found to be 0.16 μg/mL and 0.54 μg/mL for metformin HCl and LOD and LOQ were found to be 0.05 and 0.21 μg/mL for canagliflozin. Metformin HCl and canagliflozin were subjected to stress conditions of degradation including acidic, alkaline, oxidative, thermal and photolysis.

2008 ◽  
Vol 5 (3) ◽  
pp. 648-651 ◽  
Author(s):  
G. Rathinavel ◽  
P. B. Mukherjee ◽  
J. Valarmathy ◽  
L. Samueljoshua ◽  
M. Ganesh ◽  
...  

This paper presents a RP-HPLC method for the simultaneous estimation of cefixime and cloxacillin in tablets. The process was carried out on C18column (5 μm, 25 cm × 4.6 mm, i.d) using phosphate buffer (pH 5.0), acetonitrile and methanol in the ratio 80:17:3 respectively as a mobile phase at a flow rate of 2mL/min. Wavelength was fixed at 225 nm. The retention time of cefixime and cloxacillin was found to be 5.657 and 6.200 min, respectively. The developed method is rapid and sensitive and it can be used for estimation of combination of these drugs in tablets.


2019 ◽  
Vol 9 (1) ◽  
pp. 170-174
Author(s):  
Anjali Bakshi ◽  
K Monika ◽  
Shweta Bhutada ◽  
M. Bhagvan Raju

A simple, selective, linear, precise, and accurate RP-HPLC method was developed and validated for the simultaneous estimation of Gabapentin & Methylcobalamin from bulk and formulation. Chromatographic separation was achieved Isocratically on an Inertsil C18 column (150x4.6, 5µ particle size) using a mobile phase Buffer: Acetonitrile in the ratio of 60:40 v/v. The flow rate was 1.0 ml/min, effluents were detected at 264 nm and 10µl of sample was injected. Retention time of Gabapentin & Methylcobalamin was found to be 2.7 and 4.13 min respectively. Linearity of the method was in the concentration range of 25-150 µg for Gabapentin & 0.125-0.750 µg for Methylcobalamin. Percent recoveries obtained for both the drugs were 100.00%. The percentage RSD for precision of the method was found to be less than 2%. The method was validated according to the ICH guidelines. The method developed was successfully applied for the analysis of simultaneous estimation of Gabapentin & Methylcobalamin tablets and was fairly good in comparison with other methods. Keywords: Gabapentin, Methylcobalamin, HPLC.


INDIAN DRUGS ◽  
2014 ◽  
Vol 51 (01) ◽  
pp. 27-33
Author(s):  
N. R Dighade ◽  
◽  
S. P. Padmane ◽  
A. V. Kasture

The study describes a validated stability indicating reverse- phase HPLC method for the simultaneous estimation of pantoprazole and cinitapride in capsule formulation. The proposed RP-HPLC method utilizes an Eclipse XDB C18 Column (150 × 4.6 mm i.d., 5μm), optimum mobile phase consisting of 10 mM phosphate buffer: acetonitrile: THF in the ratio of 64:36:0.5 V/V (pH 3.5) V/V, effluent flow rate 1 mL/min and UV detection wavelength of 266 nm. The selected chromatographic conditions were found to effectively separate pantoprazole and cinitapride with retention time of 7.17 min and 3.56 min, respectively. Linearity for pantoprazole and cinitapride was found in the range of 2-30 μg/mL and 0.15- 2.28 μg/mL, respectively. The developed method was statistically validated for the linearity, accuracy, precision, robustness, ruggedness and specificity. The proposed method was found to be simple, accurate, precise, economical and specific. Therefore, it can be used for simultaneous analysis of these drugs in capsule formulation.


INDIAN DRUGS ◽  
2017 ◽  
Vol 54 (09) ◽  
pp. 86-88
Author(s):  
A. A Adhyapak ◽  
◽  
A. P Jadhav

A simple, precise, accurate and robust RP-HPLC method was developed and validated for simultaneous estimation of reserpine and gallic acid in an ayurvedic formulation. The two markers were resolved using a C-18 column make Hemochrom Instil using the mobile phase acetonitrile: water (pH 5.6 adjusted using orthophosphoric acid) in the ratio 75:25 V/V at a flow rate of 0.8 mL/min. Retention times of reserpine and gallic acid were 8.178 ± 0.2 minutes and 2.527 ± 0.2 minutes respectively, at 229 nm. The developed method was validated on the basis of ICH Q2 (R1) guidelines. The developed method was applied for quantification of markers in marketed formulation, Cardostab tablet.


2006 ◽  
Vol 3 (1) ◽  
pp. 60-64 ◽  
Author(s):  
P. Venkata Reddy ◽  
B. Sudha Rani ◽  
G. Srinu Babu ◽  
J. V. L. N. Seshagiri Rao

A reverse phase HPLC method is developed for the determination of Raloxifene in pharmaceutical dosage forms. Chromatography was carried out on an inertsil C18 column using a mixture of acetonitrile and phosphate buffer (30:70 v/v) as the mobile phase at a flow rate of 1 mL/min. Detection was carried out at 290 nm .The retention time of the drug was 10.609 min. The method produced linear responses in the concentration range of 0.5-200 µg/mL of Raloxifene. The method was found to be applicable for determination of the drug in tablets.


INDIAN DRUGS ◽  
2019 ◽  
Vol 56 (07) ◽  
pp. 59-68
Author(s):  
H Mahajan ◽  
S Savale ◽  
P Nerkar ◽  

The present study was aimed at developing a Reversed-Phase High-Performance Liquid Chromatography (RP-HPLC) method for simultaneous determination of curcumin (CRM) and gefitinib (GFT) in bulk, plasma and brain homogenate. hydrochlorothiazide was used as an internal standard (IS). A new simple, rapid, selective, precise and accurate RP-HPLC method has been developed. The separation was achieved by using C-18 column (Qualisil BDS C18, 250 mm x 4.6 mm I.D.) coupled with a guard column of silica, mobile phase consisted of acetonitrile: water with 0.1% formic acid (30:70 v/v). The flow rate was 0.2 ml/min and the drug was detected using PDA detector at the wavelength of 242 nm. The experimental conditions, including the diluting solvent, mobile phase composition, column saturation and flow rate, were optimised to provide high-resolution and reproducible peaks. The method was developed and tested for linearity range of 10-60 μg/mL for bulk analysis and 200-800 ng/mL for plasma and brain homogenate. The developed method was validated as per ICH guidelines, in terms of linearity, application of the proposed method to bulk sample, recovery, precision, repeatability, ruggedness, sensitivity (LOD and LOQ) and robustness and stability study (short and long-term stabilities, freeze/thaw stability, post-preparative). The low value of % RSD showed that the method was precise within the acceptance limit of 2%. The developed method was successfully applied for the analysis of the drug in bulk as well as various marketed formulation and drug in plasma and brain distribution studies.


Author(s):  
M Lakshmi Kanth ◽  
B Raj Kama

An accurate RP-HPLC method developed for the estimation of Neratinib in bulk and tablet dosage form. The method is and validated for parameters linearity, accuracy, suitability, specificity, precession, LOD, LOQ and robustness. An Altima column (150 mm × 4.6 mm × 5μ) used for chromatographic separation within a runtime of 6 min. The mobile phase buffer (monopotassium phosphate) and acetonitrile (60:40 v/v) with 0.1% formic acid is used. The flow rate maintained at 1.0 ml/min with the effluents monitored at 215 nm. The Neratinib analyzed at retention time of 4.001. The concentration linear over 30-180μg/ml with regression equation y = 6065.6x + 795.43 and regression co-efficient 0.999.


2011 ◽  
Vol 8 (3) ◽  
pp. 1238-1245 ◽  
Author(s):  
G. Tulja Rani ◽  
D. Gowri Sankar ◽  
P. Kadgapathi ◽  
B. Satyanarayana

A simple, fast, precise, selective and accurate RP-HPLC method was developed and validated for the simultaneous determination of atenolol and indapamide from bulk and formulations. Chromatographic separation was achieved isocratically on a Waters C18 column (250×4.6 mm, 5 µ particle size) using a mobile phase, methanol and water (adjusted to pH 2.7 with 1% orthophosphoric acid) in the ratio of 80:20. The flow rate was 1 mL/min and effluent was detected at 230 nm. The retention time of atenolol and indapamide were 1.766 min and 3.407 min. respectively. Linearity was observed in the concentration range of 12.5-150 µg/mL for atenolol and 0.625-7.5 µg/mL for indapamide. Percent recoveries obtained for both the drugs were 99.74-100.06% and 98.65-99.98% respectively. The method was validated according to the ICH guidelines with respect to specificity, linearity, accuracy, precision and robustness. The method developed can be used for the routine analysis of atenolol and indapamide from their combined dosage form.


2020 ◽  
Vol 11 (02) ◽  
pp. 296-302
Author(s):  
Aseem Kumar ◽  
Anil Kumar Sharma ◽  
Rohit Dutt

The present work demonstrates a simple, rapid, precise, specific, and sensitive reverse-phase high-performance liquid chromatography (RP-HPLC) method for analyzing glimepiride in pure and tablet forms. The present method was developed using a C18 column 150 × 4.6 mm, with 5 μm, and packing L1 maintained at a temperature of 30°C. The mobile phase was prepared by dissolving 0.5 gram of monobasic sodium phosphate in 500 mL of distilled water, pH of the solution adjusted to 2.1 to 2.7 with 10% phosphoric acid, and added 500 mL of acetonitrile. The mobile phase was pumped in the highperformance liquid chromatography (HPLC) system at a flow rate of 1 mL/min, and separation was carried out at 228 nm, using an ultraviolet (UV) detector. The chromatographic separation was achieved with peak retention time (RT) at about 9.30 minutes, and the method was found to be linear over a concentration range of 40 to 140 μg/mL. The specificity of the method represented no interference of the excipients during the analysis, and stability testing after 24 hours also showed that the method is suitable and specific. The accuracy was between 99.93 to 99.96%, with limit of detection (LOD) and limit of quantitation (LOQ) being 0.354 μg/mL, 1.18 μg/mL, respectively. Satisfactory results were found for precision and robustness parameters during the development and validation stage for the analytical method. The proposed method was also adopted for the analysis of glimepiride tablets to improve the overall quality control. Using this method, symmetric peak shape was obtained with reasonable retention time. The retention time of glimepiride for six repetitions is 9.3 ± 0.1 minutes; the run time is 21 minutes. The proposed RP-HPLC method is a modification of the United States Pharmacopeia (USP) method, and it was found to be valid for glimepiride within concentration ranges 40 to 140 μg/mL, using C18 analytical columns, and isocratic elution with UV detection, and at 1 mL/min of flow rate.


2009 ◽  
Vol 6 (2) ◽  
pp. 469-474 ◽  
Author(s):  
Zaheer Ahmed ◽  
B. Gopinath ◽  
A. Sathish Kumar Shetty ◽  
B. K. Sridhar

A rapid and sensitive RP-HPLC method with UV detection (262 nm) for routine analysis of adefovir dipivoxil in bulk and in pharmaceutical formulation was developed. Chromatography was performed with mobile phase containing a mixture of acetonitrile and phosphate buffer (50:50, v/v) with flow rate 1.0 mL min-l. In the range of 5.0-100 µg/mL, the linearity of adefovir dipivoxil shows a correlation co-efficient of 0.9999. The proposed method was validated by determining sensitivity accuracy, precision, robustness stability, specificity, selectivity and system suitability parameters.


Sign in / Sign up

Export Citation Format

Share Document