scholarly journals Assessment of scale of hazards due to pool fire for a fossil fired power plant in India

MAUSAM ◽  
2021 ◽  
Vol 60 (2) ◽  
pp. 197-210
Author(s):  
ARUN KUMAR ◽  
S. K. DASH ◽  
S. K. DHAKA
Keyword(s):  
Wind Speed ◽  
Power Plant ◽  
Radial Distance ◽  
High Wind ◽  
Human Settlement ◽  
Wind Speeds ◽  
Late Night ◽  
Hazardous Condition ◽  
Low Wind Speeds ◽  
Lethal Doses

Hazards for a fossil fired power plant located at   coastal Gujarat in India have been assessed.  The trajectory and spread of the plume from tanks of fossil fired power plant were predicted using existing models named Carter, Mills, Briggs and Zonato during winter and summer seasons with low and high wind speeds observed in day and night hours. Results show that wide areas of habitation and human settlement to the northeast of the site may be potentially under hazards due to southwesterly and southerly winds during summer. Plume heights and widths are found high in the morning hours or late night when wind speeds are low. As wind speed increases around noon, low plume heights and widths are obtained.   Length scales become low at low wind speeds and vice-versa. Lethal doses of thermal radiation beyond radial distance of 70 m are within the tolerable limit under hazardous condition.

scholarly journals Dependence of Power Characteristics on Savonius Rotor Segmentation

Energies ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2912
Author(s):  
Krzysztof Doerffer ◽  
Janusz Telega ◽  
Piotr Doerffer ◽  
Paulina Hercel ◽  
Andrzej Tomporowski
Keyword(s):  
High Wind ◽  
Horizontal Axis Wind Turbine ◽  
Savonius Rotor ◽  
Power Characteristics ◽  
Wind Speeds ◽  
Single Segment ◽  
High Elongation ◽  
Low Wind Speeds ◽  
Number Of Segments ◽  
Rotor Type

Savonius rotors are large and heavy because they use drag force for propulsion. This leads to a larger investment in comparison to horizontal axis wind turbine (HAWT) rotors using lift forces. A simple construction of the Savonius rotor is preferred to reduce the production effort. Therefore, it is proposed here to use single-segment rotors of high elongation. Nevertheless, this rotor type must be compared with a multi-segment rotor to prove that the simplification does not deteriorate the effectiveness. The number of segments affects the aerodynamic performance of the rotor, however, the results shown in the literature are inconsistent. The paper presents a new observation that the relation between the effectiveness of single- and multi-segment rotors depends on the wind velocity. A single-segment rotor becomes significantly more effective than a four-segment rotor at low wind speeds. At high wind speeds, the effectiveness of both rotors becomes similar.

scholarly journals Optimization of a Small Wind Power Plant for Annual Wind Speed Distribution

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1587
Author(s):  
Krzysztof Wrobel ◽  
Krzysztof Tomczewski ◽  
Artur Sliwinski ◽  
Andrzej Tomczewski
Keyword(s):  
Wind Speed ◽  
Power Plant ◽  
Wind Power ◽  
Power Plants ◽  
Control Method ◽  
Wind Power Plant ◽  
Switched Reluctance ◽  
Wind Speeds ◽  
Wind Speed Distribution ◽  
And Control

This article presents a method to adjust the elements of a small wind power plant to the wind speed characterized by the highest annual level of energy. Tests were carried out on the basis of annual wind distributions at three locations. The standard range of wind speeds was reduced to that resulting from the annual wind speed distributions in these locations. The construction of the generators and the method of their excitation were adapted to the characteristics of the turbines. The results obtained for the designed power plants were compared with those obtained for a power plant with a commercial turbine adapted to a wind speed of 10 mps. The generator structure and control method were optimized using a genetic algorithm in the MATLAB program (Mathworks, Natick, MA, USA); magnetostatic calculations were carried out using the FEMM program; the simulations were conducted using a proprietary simulation program. The simulation results were verified by measurement for a switched reluctance machine of the same voltage, power, and design. Finally, the yields of the designed generators in various locations were determined.

scholarly journals Bayesian Model Averaging for Wind Speed Ensemble Forecasts Using Wind Speed and Direction

2017 ◽  
Vol 32 (6) ◽  
pp. 2217-2227 ◽  
Author(s):  
Siri Sofie Eide ◽  
John Bjørnar Bremnes ◽  
Ingelin Steinsland
Keyword(s):  
Wind Speed ◽  
Wind Direction ◽  
Bayesian Model Averaging ◽  
Weather Prediction ◽  
Model Averaging ◽  
Strong Wind ◽  
Ensemble Forecasts ◽  
Wind Speeds ◽  
Low Wind Speeds ◽  
The One

Abstract In this paper, probabilistic wind speed forecasts are constructed based on ensemble numerical weather prediction (NWP) forecasts for both wind speed and wind direction. Including other NWP variables in addition to the one subject to forecasting is common for statistical calibration of deterministic forecasts. However, this practice is rarely seen for ensemble forecasts, probably because of a lack of methods. A Bayesian modeling approach (BMA) is adopted, and a flexible model class based on splines is introduced for the mean model. The spline model allows both wind speed and wind direction to be included nonlinearly. The proposed methodology is tested for forecasting hourly maximum 10-min wind speeds based on ensemble forecasts from the European Centre for Medium-Range Weather Forecasts at 204 locations in Norway for lead times from +12 to +108 h. An improvement in the continuous ranked probability score is seen for approximately 85% of the locations using the proposed method compared to standard BMA based on only wind speed forecasts. For moderate-to-strong wind the improvement is substantial, while for low wind speeds there is generally less or no improvement. On average, the improvement is 5%. The proposed methodology can be extended to include more NWP variables in the calibration and can also be applied to other variables.

scholarly journals Wind Power potential in Kigali and Western provinces of Rwanda

2015 ◽  
Vol 2 (1) ◽  
pp. 25-36
Author(s):  
Otieno Fredrick Onyango ◽  
Sibomana Gaston ◽  
Elie Kabende ◽  
Felix Nkunda ◽  
Jared Hera Ndeda
Keyword(s):  
Wind Speed ◽  
Probability Density ◽  
Wind Power ◽  
Wind Direction ◽  
Small Scale ◽  
Energy Potential ◽  
Wind Speeds ◽  
Mean Wind Speed ◽  
Wind Energy Potential ◽  
Low Wind Speeds

Wind speed and wind direction are the most important characteristics for assessing wind energy potential of a location using suitable probability density functions. In this investigation, a hybrid-Weibull probability density function was used to analyze data from Kigali, Gisenyi, and Kamembe stations. Kigali is located in the Eastern side of Rwanda while Gisenyi and Kamembe are to the West. On-site hourly wind speed and wind direction data for the year 2007 were analyzed using Matlab programmes. The annual mean wind speed for Kigali, Gisenyi, and Kamembe sites were determined as 2.36m/s, 2.95m/s and 2.97m/s respectively, while corresponding dominant wind directions for the stations were ,  and  respectively. The annual wind power density of Kigali was found to be  while the power densities for Gisenyi and Kamembe were determined as and . It is clear, the investigated regions are dominated by low wind speeds thus are suitable for small-scale wind power generation especially at Kamembe site.

scholarly journals Catch Characteristics of Precipitation Gauges in High-Latitude Regions with High Winds

2006 ◽  
Vol 7 (5) ◽  
pp. 984-994 ◽  
Author(s):  
Konosuke Sugiura ◽  
Tetsuo Ohata ◽  
Daqing Yang
Keyword(s):  
Wind Speed ◽  
High Latitude ◽  
Cold Climate ◽  
Strong Wind ◽  
Blowing Snow ◽  
High Wind ◽  
Wind Speeds ◽  
Solid Precipitation ◽  
High Winds ◽  
Correction Equations

Abstract Intercomparison of solid precipitation measurement at Barrow, Alaska, has been carried out to examine the catch characteristics of various precipitation gauges in high-latitude regions with high winds and to evaluate the applicability of the WMO precipitation correction procedures. Five manual precipitation gauges (Canadian Nipher, Hellmann, Russian Tretyakov, U.S. 8-in., and Wyoming gauges) and a double fence intercomparison reference (DFIR) as an international reference standard have been installed. The data collected in the last three winters indicates that the amount of solid precipitation is characteristically low, and the zero-catch frequency of the nonshielded gauges is considerably high, 60%–80% of precipitation occurrences. The zero catch in high-latitude high-wind regions becomes a significant fraction of the total precipitation. At low wind speeds, the catch characteristics of the gauges are roughly similar to the DFIR, although it is noteworthy that the daily catch ratios decreased more rapidly with increasing wind speed compared to the WMO correction equations. The dependency of the daily catch ratios on air temperature was confirmed, and the rapid decrease in the daily catch ratios is due to small snow particles caused by the cold climate. The daily catch ratio of the Wyoming gauge clearly shows wind-induced losses. In addition, the daily catch ratios are considerably scattered under strong wind conditions due to the influence of blowing snow. This result suggests that it is not appropriate to extrapolate the WMO correction equations for the shielded gauges in high-latitude regions for high wind speed of over 6 m s−1.

Calibration and Cross Validation of Global Ocean Wind Speed Based on Scatterometer Observations

2020 ◽  
Vol 37 (2) ◽  
pp. 279-297 ◽  
Author(s):  
Agustinus Ribal ◽  
Ian R. Young
Keyword(s):  
Wind Speed ◽  
Cross Validation ◽  
Regression Line ◽  
Total Duration ◽  
Global Ocean ◽  
High Wind ◽  
Wind Speeds ◽  
Buoy Data ◽  
Ocean Wind

AbstractGlobal ocean wind speed observed from seven different scatterometers, namely, ERS-1, ERS-2, QuikSCAT, MetOp-A, OceanSat-2, MetOp-B, and Rapid Scatterometer (RapidScat) were calibrated against National Data Buoy Center (NDBC) data to form a consistent long-term database of wind speed and direction. Each scatterometer was calibrated independently against NDBC buoy data and then cross validation between scatterometers was performed. The total duration of all scatterometer data is approximately 27 years, from 1992 until 2018. For calibration purposes, only buoys that are greater than 50 km offshore were used. Moreover, only scatterometer data within 50 km of the buoy and for which the overpass occurred within 30 min of the buoy recording data were considered as a “matchup.” To carry out the calibration, reduced major axis (RMA) regression has been applied where the regression minimizes the size of the triangle formed by the vertical and horizontal offsets of the data point from the regression line and the line itself. Differences between scatterometer and buoy data as a function of time were investigated for long-term stability. In addition, cross validation between scatterometers and independent altimeters was also performed for consistency. The performance of the scatterometers at high wind speeds was examined against buoy and platform measurements using quantile–quantile (Q–Q) plots. Where necessary, corrections were applied to ensure scatterometer data agreed with the in situ wind speed for high wind speeds. The resulting combined dataset is believed to be unique, representing the first long-duration multimission scatterometer dataset consistently calibrated, validated and quality controlled.

scholarly journals Strategies for Enhancing the Low Wind Speed Performance of H-Darrieus Wind Turbine—Part 1

2019 ◽  
Vol 1 (1) ◽  
pp. 185-204 ◽  
Author(s):  
Palanisamy Mohan Kumar ◽  
Krishnamoorthi Sivalingam ◽  
Teik-Cheng Lim ◽  
Seeram Ramakrishna ◽  
He Wei
Keyword(s):  
Wind Speed ◽  
Poor Performance ◽  
Vertical Axis ◽  
Speed Ratio ◽  
Wind Speeds ◽  
Low Wind Speed ◽  
Viable Solution ◽  
Speed Performance ◽  
Low Wind Speeds ◽  
Starting Characteristics

Small wind turbines are key devices for micro generation in particular, with a notable contribution to the global wind energy sector. Darrieus turbines, despite being highly efficient among various types of vertical axis turbines, received much less attention due to their starting characteristics and poor performance in low wind speeds. Radically different concepts are proposed as a potential solution to enhance the performance of Darrieus turbine in the weak wind flows, all along the course of Darrieus turbine development. This paper presents a comprehensive review of proposed concepts with the focus set on the low wind speed performance and critically assessing their applicability based on economics, reliability, complexity, and commercialization aspects. The study is first of its kind to consolidate and compare various approaches studied on the Darrieus turbine with the objective of increasing performance at low wind. Most of the evaluated solutions demonstrate better performance only in the limited tip speed ratio, though they improve the low wind speed performance. Several recommendations have been developed based on the evaluated concepts, and we concluded that further critical research is required for a viable solution in making the Darrieus turbine a low speed device.

Identification of aerodynamic derivatives of bridge decks at high testing wind speed

2018 ◽  
Vol 45 (11) ◽  
pp. 1004-1014
Author(s):  
Quanshun Ding ◽  
Shuanghu Dong ◽  
Zhiyong Zhou
Keyword(s):  
Wind Speed ◽  
Wind Tunnel Test ◽  
Participation Rate ◽  
Single Mode ◽  
High Wind ◽  
Wind Speeds ◽  
Aerodynamic Derivatives ◽  
Vibration Responses ◽  
Mode Extraction ◽  
Derivatives Of

An identification of eight aerodynamic derivatives based on dual-mode and single-mode extraction of system is presented to improve the applicability and accuracy of identification at high testing wind speed. The participation rate to measure the contribution of modes on free-vibration responses is defined and the single-mode extraction is presented to extract the modal parameters of the system at high wind speed. To verify the reliability and applicability of the presented method, the aerodynamic derivatives of a dummy section with known self-excited forces are identified. It is noted that there is a very good agreement between the identified results and the target ones in the range of the low and high wind speeds and the presented method works well after the critical state of flutter. The sectional wind tunnel test of the Tanggu-haihe bridge is performed to identify the aerodynamic derivatives of the deck at the attack angles of −3°, 0°, and 3°.

scholarly journals The gasoline vapors spread from “small” spills in an urban environment at low wind speeds

2020 ◽  
Vol 164 ◽  
pp. 01006
Author(s):  
Ruslan Khrestenko ◽  
Ekaterina Sokolova ◽  
Dmitrii Okulovsky ◽  
Valeri Azarov
Keyword(s):  
Wind Speed ◽  
Urban Environment ◽  
Surface Area ◽  
Experimental Studies ◽  
Calculated Data ◽  
Hazardous Substances ◽  
Ethyl Benzene ◽  
Atmospheric Air ◽  
Wind Speeds ◽  
Low Wind Speeds

It is noted that the urban environment is polluted by oil products; in particular, there is a large pollution of atmospheric air. It is indicated that one of the pollution sources is the “small” spills, which are characteristic of urban areas. Experimental studies have been carried out on the gasoline distribution in atmospheric air at “small” spills. A single experiment at a low wind speed is considered. Data were obtained on the dependence of gasoline concentration in atmospheric air on the distance from the spill, the height above the level of the spill and the time of the spill. The component composition was studied using chromatographic studies. It is indicated that the distribution of gasoline vapors in the atmosphere is influenced by the ambient temperature, wind speed, surface area of the spill, time from the moment of spilling and the distance above the level of the spill. The gasoline dispersion in atmospheric air was calculated with the software using experimental and calculated data on the surface area of the spill. It is indicated that at low wind speeds (up to 0.5 m/s) from “small” spills of gasoline (up to 3 liters), significant excesses of standards for the content of harmful substances in the atmospheric air can be observed. It was determined that during spilling there is an excess of maximum permissible concentrations of single, hazardous substances such as ethyl benzene, m-xylene and amyl alcohol in the air.

scholarly journals Airborne Spectral Measurements of Ocean Directional Reflectance

2005 ◽  
Vol 62 (4) ◽  
pp. 1072-1092 ◽  
Author(s):  
Charles K. Gatebe ◽  
Michael D. King ◽  
Alexei I. Lyapustin ◽  
G. Thomas Arnold ◽  
Jens Redemann
Keyword(s):  
Wind Speed ◽  
Transfer Problem ◽  
Strong Dependence ◽  
Radiative Transfer Problem ◽  
Airborne Measurements ◽  
Wind Speeds ◽  
Research Aircraft ◽  
Low Wind Speeds ◽  
The University ◽  
Bidirectional Reflectance Distribution

Abstract The Cloud Absorption Radiometer (CAR) was flown aboard the University of Washington Convair 580 (CV-580) research aircraft during the Chesapeake Lighthouse and Aircraft Measurements for Satellites (CLAMS) field campaign and obtained measurements of bidirectional reflectance distribution function (BRDF) of the ocean in July and August 2001 under different illumination conditions with solar zenith angles ranging from 15° to 46°. The BRDF measurements were accompanied by concurrent measurements of atmospheric aerosol optical thickness and column water vapor above the airplane. The method of spherical harmonics with Cox–Munk wave-slope distribution is used in a new algorithm developed for this study to solve the atmosphere–ocean radiative transfer problem and to remove the effects of the atmosphere from airborne measurements. The algorithm retrieves simultaneously the wind speed and full ocean BRDF (sun’s glitter and water-leaving radiance) from CAR measurements and evaluates total albedo and equivalent albedo for the water-leaving radiance outside the glitter. Results show good overall agreement with other measurements and theoretical simulations, with the anisotropy of the water-leaving radiance clearly seen. However, the water-leaving radiance does not show a strong dependence on solar zenith angle as suggested by some theoretical studies. The spectral albedo was found to vary from 4.1%–5.1% at λ = 0.472 μm to 2.4%–3.5% for λ ≥ 0.682 μm. The equivalent water-leaving albedo ranges from 1.0%–2.4% at λ = 0.472 μm to 0.1%–0.6% for λ = 0.682 μm and 0.1%–0.3% for λ = 0.870 μm. Results of the validation of the Cox–Munk model under the conditions measured show that although the model reproduces the shape of sun’s glitter on average with an accuracy of better than 30%, it underestimates the center of the sun’s glitter reflectance by about 30% for low wind speeds (<2–3 m s−1). In cases of high wind speed, the model with Gram–Charlier expansion seems to provide the best fit.

Sign in / Sign up

Export Citation Format

Share Document