IMPACT OF WOOD RAW MATERIALS MOVEMENT PARAMETERS ON THE ANNEALING REACTOR TORREFACTION EFFICIENCY

2020 ◽  
Author(s):  
Ruslan Safin ◽  
Albina V. Safina ◽  
Ekaterina I. Baigildeeva ◽  
Pavel A. Kainov ◽  
Ksenia V. Saerova
Keyword(s):  
Raw Materials ◽  
Movement Parameters

Microstructural characterization of laser-melted/roller-quenched dicalcium silicate

1988 ◽  
Vol 46 ◽  
pp. 582-583
Author(s):  
C. J. Chan ◽  
K. R. Venkatachari ◽  
W. M. Kriven ◽  
J. F. Young
Keyword(s):  
Particle Size ◽  
Raw Materials ◽  
Shape Change ◽  
Microstructural Characterization ◽  
Particle Size Effect ◽  
Dicalcium Silicate ◽  
Laser Melting ◽  
Uniform Size ◽  
Cell Shape Change ◽  
Wide Range

Dicalcium silicate (Ca2SiO4) is a major component of Portland cement. It has also been investigated as a potential transformation toughener alternative to zirconia. It has five polymorphs: α, α'H, α'L, β and γ. Of interest is the β-to-γ transformation on cooling at about 490°C. This transformation, accompanied by a 12% volume increase and a 4.6° unit cell shape change, is analogous to the tetragonal-to-monoclinic transformation in zirconia. Due to the processing methods used, previous studies into the particle size effect were limited by a wide range of particle size distribution. In an attempt to obtain a more uniform size, a fast quench rate involving a laser-melting/roller-quenching technique was investigated.The laser-melting/roller-quenching experiment used precompacted bars of stoichiometric γ-Ca2SiO4 powder, which were synthesized from AR grade CaCO3 and SiO2xH2O. The raw materials were mixed by conventional ceramic processing techniques, and sintered at 1450°C. The dusted γ-Ca2SiO4 powder was uniaxially pressed into 0.4 cm x 0.4 cm x 4 cm bars under 34 MPa and cold isostatically pressed under 172 MPa. The γ-Ca2SiO4 bars were melted by a 10 KW-CO2 laser.

Crystallization of barium hexaferrite

1992 ◽  
Vol 50 (1) ◽  
pp. 362-363
Author(s):  
Chung-kook Lee ◽  
Yolande Berta ◽  
Robert F. Speyer
Keyword(s):  
Size Distribution ◽  
Raw Materials ◽  
Barium Hexaferrite ◽  
Recording Media ◽  
Magnetic Recording Media ◽  
Promising Candidate ◽  
Crystallization Method ◽  
Temperature Heat ◽  
High Density Magnetic Recording ◽  
Temperature Heat Treatment

Barium hexaferrite (BaFe12O19) is a promising candidate for high density magnetic recording media due to its superior magnetic properties. For particulate recording media, nano-sized single crystalline powders with a narrow size distribution are a primary application requirement. The glass-crystallization method is preferred because of the controllability of crystallization kinetics, hence, particle size and size distribution. A disadvantage of this method is the need to melt raw materials at high temperatures with non-reactive crucibles, e.g. platinum. However, in this work, we have shown that crystal growth of barium hexaferrite occurred during low temperature heat treatment of raw batches.

A possibility of using nickel concentrate, obtained as a result of hydrometallurgical enrichment of manganese-containing raw materials, at steel alloying

2020 ◽  
Vol 76 (7) ◽  
pp. 709-715
Author(s):  
O. Yu. Kichigina
Keyword(s):  
Raw Materials ◽  
Experimental Studies ◽  
Selective Extraction ◽  
Technological Parameters ◽  
Nickel Iron ◽  
Nickel Recovery ◽  
Nickel Concentrate ◽  
Steel Alloying ◽  
High Degree ◽  
Comprehensive Processing

At production of stainless steel expensive alloying elements, containing nickel, are used. To decrease the steel cost, substitution of nickel during steel alloying process by its oxides is an actual task. Results of analysis of thermodynamic and experimental studies of nickel reducing from its oxide presented, as well as methods of nickel oxide obtaining at manganese bearing complex raw materials enrichment and practice of its application during steel alloying. Technology of comprehensive processing of complex manganese-containing raw materials considered, including leaching and selective extraction out of the solution valuable components: manganese, nickel, iron, cobalt and copper. Based on theoretical and experiment studies, a possibility of substitution of metal nickel by concentrates, obtained as a result of hydrometallurgical enrichment, was confirmed. Optimal technological parameters, ensuring high degree of nickel recovery out of the initial raw materials were determined. It was established, that for direct steel alloying it is reasonable to add into the charge pellets, consisting of nickel concentrate and coke fines, that enables to reach the through nickel recovery at a level of 90%. The proposed method of alloying steel by nickel gives a possibility to decrease considerably steel cost at the expense of application of nickel concentrate, obtained out of tails of hydrometallurgical enrichment of manganese-bearing raw materials, which is much cheaper comparing with the metal nickel.

Problems of ensuring metrological traceability of measurement results of indicators of quality for food products and food raw materials

2020 ◽  
pp. 64-70
Author(s):  
Mariya Y. Medvedevskikh ◽  
Anna S. Sergeeva
Keyword(s):  
Reference Materials ◽  
Mass Fraction ◽  
Nutritional Value ◽  
Animal Feed ◽  
Raw Materials ◽  
Meat Products ◽  
Metrological Traceability ◽  
Food Products ◽  
Freeze Dried ◽  
Measurement Results

The article raises the problem of ensuring metrological traceability of the measurement results of indicators of quality and nutritional value for food products and food raw materials: water (moisture), nitrogen (protein, crude protein), fat, ash and carbohydrates. The problem under consideration can be solved by applying reference materials of food composition, traceable to state primary measurement standards GET 173-2017 and GET 176-2019 and primary reference measurement procedures (PRMP), for attestation of measurement procedures and accuracy checking of measurement results. The article discusses the results of the PRMP development of mass fraction of fat, ash and carbohydrates in food products and food raw materials, as well as mass fraction of crude fat (oil content) in oil crops seeds and products based on them. The paper also presents metrological characteristics of reference materials of composition of dry dairy products, grain-milk dry porridges for nutrition of babies, grain dry porridges for nutrition of babies, egg powder, freeze-dried meat products, animal feed. The results of the work allow for building a chain of metrological traceability from GET 173-2017, GET 176-2019 and PRMP to routine measurement procedures, thereby ensuring the uniformity of measurements of nutritional value of food products.

Sign in / Sign up

Export Citation Format

Share Document