The influence of temperature on selected strength properties of furniture particleboard

2019 ◽  
Vol 108 ◽  
pp. 128-134
Author(s):  
PIOTR BORYSIUK ◽  
ANNA TETELEWSKA ◽  
AURIGA RADOSŁAW ◽  
IZABELLA JENCZYK-TOŁŁOCZKO

The influence of temperature on selected strength properties of furniture particleboard. As a part of the study, the influence of temperature on selected properties of furniture particleboard was tested. P2 type industrial particleboards in three finishing options: raw boards (1), boards covered with melamine film in white (2) and black (3) (10 samples per variant) have been subjected to temperatures from -20oC to +120oC, at 10oC intervals. The Time of exposure for individual temperatures was 7 days. MOR, MOE and IB were determined for tested boards. It has been shown that temperatures above 50oC have a negative effect on strength properties of boards. A large decrease in all tested parameters was observed in the temperature range from +60oC to +120oC. It was also noted that finishing boards with melamine film did not improve their durability.

1997 ◽  
Vol 506 ◽  
Author(s):  
W. J. Cho ◽  
J. O. Lee ◽  
K. S. Chun

ABSTRACTThe hydraulic conductivities in water saturated bentonites at different densities were measured within temperature range of 20 to 80 °C. The results show that the hydraulic conductivities increase with increasing temperature. The hydraulic conductivities of bentonites at the temperature of 80 °C increase up to about 3 times as high as those at 20 °C. The measured values are in good agreement with those predicted. The change in viscosity of water with temperature contributes greatly to increase of hydraulic conductivity.


2008 ◽  
Vol 607 ◽  
pp. 213-217 ◽  
Author(s):  
Sergey V. Stepanov ◽  
Gilles Duplâtre ◽  
Vsevolod Byakov ◽  
V.S. Subrahmanyam ◽  
Dmitry Zvezhinskiy ◽  
...  

Positron annihilation lifetime (PAL) spectra are measured in liquid water in the temperature range 2 – 930C. The spectra are treated by taking into account intratrack reactions and assuming that radical reactions with Ps are diffusion-controlled (the respective temperature dependences obeying the Stokes-Einstein law). Equilibrium Ps bubble parameters are obtained.


2013 ◽  
Vol 795 ◽  
pp. 419-423 ◽  
Author(s):  
J.H. Lim ◽  
C.K. Yeoh ◽  
Pei Leng Teh ◽  
W.M. Arif ◽  
A. Chik

In this paper, different sintering temperature used to study the influence of temperature on the structural and thermal properties of zinc oxide (ZnO). On this research, the sample was prepared by solid-state method for zinc oxide (ZnO) at different sintering temperature which was 700°C, 800°C and 900°C. It was observed that the density of bulk ZnO that sintering at 900°C had the higher value of density 5.03 g/cm3. The microhardness of the bulk ZnO had a higher measurement 397.3 Hv after sintered at 900°C. ZnO that sintering at 900°C had been observed that had thermal conductivity 1.1611W/cm-K in the sintering temperature range 700°C to 900°C.


1968 ◽  
Vol 46 (6) ◽  
pp. 705-712 ◽  
Author(s):  
Philippe M. Glotin

Silicon samples have been bombarded with 20-keV phosphorus ions along the easy channeling direction. Annealing temperatures and activation energies of the defects created during irradiation have been determined using a Corbino structure. The nature of the defects varies as a function of depth. Large clusters exist in the superficial layers when mainly E and A centers have been identified in the channeled part of the profile. The influence of these defects on ion ranges is shown. The most important consequence of this study is to indicate a useful temperature range, between 550 and 650 °C, for phosphorus implantation into silicon.


1967 ◽  
Vol 99 (3) ◽  
pp. 244-249 ◽  
Author(s):  
W. A. Smirnoff

AbstractThe effect of temperatures on the development of a virus disease of Neodiprion swainei Midd. was studied at constant temperatures of 30° and 12 °C., and under fluctuating temperatures (15°–20 °C.) in the laboratory and outdoors. Viral concentrations of 30 × 106 polyhedra per ml. and 1 × 106 polyhedra per ml. were used. Only the higher concentration of virus was effective at 30 °C. At 12 °C. the incubation period of the disease was prolonged and mortality caused by the virus was considerably reduced for both viral concentrations. Mortality due to the virus was similar at both viral concentrations for the fluctuating temperatures which were within the optimum temperature range for larval development.


1943 ◽  
Vol 34 (1) ◽  
pp. 1-17 ◽  
Author(s):  
H. G. Andrewartha

Diapause should not be confused with simple inhibition of growth due to cold.The embryo of the grasshopper, Austroicetes cruciata, enters a state of diapause a few days after the egg is laid. The diapause is obligate like that found in the eggs of Circotettix, rather than facultative like that found in the larvae of Platyedra. These types of diapause should be regarded as two extremes of the one phenomenon rather than two distinct phenomena.Diapause was eliminated when the egg was exposed to adequate low temperature for an adequate period when the embryo was at a suitable stage of development. If the period at low temperature was inadequate, or if the embryo was not at a suitable stage of development when the exposure to low temperature occurred, diapause was only partially eliminated. In such cases, the exposure to low temperature resulted in an abnormal growth by the embryo when the egg was returned to a favourable high temperature, but development was not completed.The influence of low temperature on the elimination of diapause was due chiefly to changes which occurred in the yolk during exposure to low temperature. Thus yolk which had been modified in this way became suitable for the nourishment of the embryo, and it no longer obstructed katatrepsis. This explanation of the nature of the obligate diapause in the eggs of Austroicetes brings this phenomenon into line with the facultative diapause in the larvae of Platyedra, which has been shown to be associated with the nourishment of the larva.Diapause was eliminated most rapidly at temperatures between 6°C. and 13°C. The embryo grew most rapidly at about 30°C. ; below 13°C. growth practically ceased. The absence of overlapping of the temperature ranges for these two processes may explain the presence of diapause in Austroicetes. The occurrence of a less pronounced diapause in the eggs of Melanoplus may be due to a partial overlapping of the temperature range for the two processes. Similarly the absence of diapause in the eggs of Locusta may be explained on the assumption that in this species the two processes proceed over the same temperature range.


2021 ◽  
pp. 014459872110408
Author(s):  
Zhiwei Zhai ◽  
Kunchao Li ◽  
Xing Bao ◽  
Jing Tong ◽  
Hongmei Yang ◽  
...  

It is crucial to obtain the representative relative permeability curves for related numerical simulation and oilfield development. The influence of temperature on the relative permeability curve remains unclear. An unsteady method was adopted to investigate the influence of temperature (range from 25–130 °C) on the oil–water relative permeability curve of sandstone reservoirs in different blocks. Then, the experimental data was analyzed by using an improved Johnson–Bossler–Naumann method. Results reveal that with the increase in temperature within a certain temperature range: (1) the relative permeability of the oil and water phases increases; (2) the irreducible water saturation increases linearly, whereas the residual oil saturation decreases nonlinearly, and the oil recovery factor increases; and (3) the saturation of two equal permeability points moves to the right, and hydrophilicity becomes stronger. The findings will aid future numerical simulation studies, thus leading to the improvement of oil displacement efficiency.


2017 ◽  
Vol 44 (2) ◽  
pp. 9-14
Author(s):  
A.M. Vagizov ◽  
G.R. Khusainova ◽  
I.G. Akhmetov ◽  
A.G. Sakhabutdinov

The relationships governing 1,3-butadiene copolymerisation in a hexane solvent in the temperature range 30–70°C were studied. The copolymerisation process was initiated by n-butyllithium. A mixture of alkali metal and alkaline earth metal amine-containing alcoholates (AMD) was used as the modifier. The microstructure and macrostructure of the obtained p-SBR specimens were investigated. In p-SBR specimens obtained in the presence of AMD in the investigated temperature range, the distribution of styrene units in block was not found. The introduction of AMD leads to the disappearance of the induction period and to an increase in the copolymerisation rate, i.e. the reactivity of the system increases, and a reduction in temperature accelerates this process. It was shown that, with increase in the process temperature, there is a reduction in the average molecular weights of the copolymer. In the presence of AMD, lowering of the copolymerisation temperature leads to ‘enrichment’ of the butadiene part in 1,2-units (up to 66.3%).


Sign in / Sign up

Export Citation Format

Share Document