The Dependency of Kinetic Parameters as a Function of Initial Solute Concentration: New Insight from Adsorption of Dye and Heavy Metals onto Humic-Like Modified Adsorbents

2021 ◽  
Vol 16 (4) ◽  
pp. 773-795
Author(s):  
Rahmat Basuki ◽  
Bambang Rusdiarso ◽  
Sri Juari Santosa ◽  
Dwi Siswanta
Keyword(s):  
Kinetic Parameters ◽  
Solute Concentration ◽  
Reaction Model ◽  
Kinetics Model ◽  
Kinetics Parameters ◽  
Rate Limiting Step ◽  
Initial Solute ◽  
Intra Particle Diffusion ◽  
Modified Adsorbents ◽  
Rate Limiting

Kinetics parameters are the essential issue in the design of water treatment systems for pollutants uptake. Though numerous studies have identified the boundary conditions that exert influence on the kinetics parameters, the influence of the dynamic initial solute concentration (C0) to the kinetic parameters generated from fitting kinetics model to experimental data has not been investigated thoroughly. This study revealed a change in the kinetics parameter value due to changes in the adsorption mechanism as an effect of dynamic C0. It was observed that at higher C0 the adsorbed solute at equilibrium (qe) increases and it takes longer time to reach equilibrium. As a result, the kinetics rate constant (k) calculated from adsorption reaction model (Lagergren, Ho, Santosa, and RBS) was decreased. In general, Ho model exhibit higher correlation coefficient value (R2) among the other model at low C0. At high C0, Ho’s R2 tend to decrease while the Lagergren and RBS’s R2 was increased. The amendment mechanism from external mass transport to intra-particle diffusion as a rate limiting step was evidenced by Boyd and Weber-Morris kinetics model. Further, the physicochemical properties of the adsorbent used in this work: chitin and Fe3O4 modified horse dung humic acid (HDHA-Fe3O4 and HDHA-Ch, respectively) with the solute: Pb(II), Methylene Blue (MB), and Ni(II) was deeply discussed in this paper. The outcomes of this work are of prime significance for effective and optimum design for pollutant uptake by adsorption equipment. Copyright © 2021 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0). 

Removal of Mg from spring water using natural clinoptilolite

Clay Minerals ◽  
2012 ◽  
Vol 47 (1) ◽  
pp. 81-92 ◽  
Author(s):  
S. Tomić ◽  
N. Rajić ◽  
J. Hrenović ◽  
D. Povrenović
Keyword(s):  
Ion Exchange ◽  
Kinetic Studies ◽  
Spring Water ◽  
Zeolite A ◽  
Zeolitic Tuff ◽  
Rate Limiting Step ◽  
Intra Particle Diffusion ◽  
Pseudo Second Order ◽  
Natural Clinoptilolite ◽  
Rate Limiting

AbstractNatural zeolitic tuff from Brus (Serbia) consisting mostly of clinoptilolite (about 90%) has been investigated for the reduction of the Mg concentration in spring water. The sorption capacity of the zeolite is relatively low (about 2.5 mg Mg g-1for the initial concentration of 100 mg Mg dm-3). The zeolitic tuff removes Mg from water solutions by ion exchange, which has been demonstrated by energy dispersive X-ray analysis (EDS). The extent of ion exchange was influenced by the pH and the initial Mg concentration. Kinetic studies revealed that Lagergen's pseudo-second order model was followed. Intra-particle diffusion of Mg2+influenced the ion exchange, but it is not the rate-limiting step. Rather than having to dispose of the Mg-loaded (waste) zeolite, a possible application was tested. Addition to a wastewater with a low concentration of Mg showed that it could successfully make up for the lack of Mg micronutrient and, accordingly, enabled the growth of phosphate-accumulating bacteriaA. Junii, increasing the amount of phosphate removed from the wastewater.

Synthesis of the Water-Compatible P-Aminophenol Resin and its Adsorption for Salicylic Acid

2011 ◽  
Vol 311-313 ◽  
pp. 1852-1856 ◽  
Author(s):  
Gu Qing Xiao ◽  
Xue Jun Zhang
Keyword(s):  
Salicylic Acid ◽  
Adsorption Capacity ◽  
Equilibrium Concentration ◽  
Maximum Adsorption Capacity ◽  
Adsorption Dynamics ◽  
First Order ◽  
Rate Limiting Step ◽  
Intra Particle Diffusion ◽  
Rate Limiting ◽  
Order Rate Equation

A novel water-compatible hypercrosslinked resin modified by p-aminophenol was synthesized with chloromethylated polystyrene and p-aminophenol by Friedel-Crafts reaction. The objective of this work was to study the adsorption performances for salicylic acid onto p-aminophenol resin. The results showed that the adsorption capacity of salicylic acid onto p-aminophenol resin was superior to XAD-4 resin. It is seen that the maximum adsorption capacity is observed at pH of 3.0. It was found the adsorption dynamics obeyed the pseudo-first-order rate equation and the intra-particle diffusion was the rate-limiting step. The maximum adsorption capacity of salicylic acid for p-aminophenol resin was measured to be 283.7 mg/g with the equilibrium concentration at 404.6mg/L. The micropore structure, the pore diameter of p-aminophenol resin, the hydrogen bond between p-aminophenol resin and salicylic acid bring the larger adsorption capacity.

scholarly journals Behavior of mesoporous activated carbon used as a remover in Congo red adsorption process

2018 ◽  
Vol 2017 (1) ◽  
pp. 170-183 ◽  
Author(s):  
Hasan Sayğılı ◽  
Fuat Güzel
Keyword(s):  
Activated Carbon ◽  
Congo Red ◽  
Low Cost ◽  
Solution Temperature ◽  
Maximum Adsorption Capacity ◽  
Tomato Paste ◽  
Rate Limiting Step ◽  
Intra Particle Diffusion ◽  
Optimized Conditions ◽  
Rate Limiting

Abstract The adsorption characteristics of Congo red (CR) dye on activated carbon produced under optimized conditions from tomato paste waste were evaluated. The effects of adsorbent dose, initial dye concentration, contact time, ionic strength and solution temperature on adsorption were investigated. Adsorption kinetic was better described by the pseudo-first order model. Results of the intra-particle diffusion model show that the pore diffusion is not the only rate-limiting step. Adsorption isotherm was well defined by the Langmuir isotherm. The maximum adsorption capacity of the activated carbon was 435 mg g−1 at 328 K. The dimensionless separation factor RL revealed the favorable nature of the isotherm of the activated carbon–dye system. Adsorption energy was found to be 4.20–4.55 kJ mol−1 indicating that the mechanism of adsorption is physical in nature. Thermodynamic studies showed that CR adsorption onto activated carbon was feasible, spontaneous and endothermic. Desorption of the used activated carbon was studied using ethanol as solvent and desorption efficiency of 56.4% was obtained after five cycles. The findings indicated that the activated carbon is a very effective and low-cost adsorbent for removal of CR dye from aqueous solutions.

scholarly journals Equilibrium, Kinetics and Thermodynamics of the Bleaching of Palm Oil Using Activated Nando Clay

2018 ◽  
pp. 1-13
Author(s):  
Nwabanne, Joseph T. ◽  
Onu, Chijioke E. ◽  
Nwankwoukwu, Okwudili C.
Keyword(s):  
Palm Oil ◽  
Order Kinetic ◽  
Adsorbent Dosage ◽  
Bleaching Efficiency ◽  
Rate Limiting Step ◽  
Equilibrium Data ◽  
Intra Particle Diffusion ◽  
Different Temperatures ◽  
Pseudo Second Order ◽  
Rate Limiting

The effectiveness of Nando clay in the bleaching of palm oil was studied in this work. The clay was prepared by activating it with hydrochloric acid. The bleaching was carried out at different temperatures, adsorbent dosage and particle sizes. The result suggests that increase in temperature and adsorbent dosage increases the bleaching efficiency while the increase in particle size decreases the bleaching efficiency. Both the pseudo-first-order and the pseudo-second-order kinetic models describe efficiently the experimental data of the bleaching process. Intra-particle diffusion though involved in the adsorptive bleaching mechanism, is not the sole rate-limiting step in the bleaching of palm oil with activated Nando clay. The equilibrium data were described better by Langmuir and Freundlich models. The enthalpy, entropy and activation energy were determined to be 6.127 KJ/mol, 3.982 KJ/mol and 15.281 KJ respectively. The free energy was found to vary between- 3.999 to- 3.760 KJ/mol. The result indicates that bleaching efficiency of up to 96% can be obtained with the activated clay as an adsorbent.

scholarly journals Removal of copper from an electroplating industrial effluent using the native and modified spirogyra

2018 ◽  
Vol 78 (1) ◽  
pp. 147-155 ◽  
Author(s):  
Nimra Ilyas ◽  
Sadia Ilyas ◽  
Sajjad-ur-Rahman ◽  
Sidra Yousaf ◽  
Aqsa Zia ◽  
...  
Keyword(s):  
Industrial Effluent ◽  
Order Kinetic ◽  
Sorption Data ◽  
Freundlich Model ◽  
First Order ◽  
Rate Limiting Step ◽  
Limiting Step ◽  
Intra Particle Diffusion ◽  
Pseudo Second Order ◽  
Rate Limiting

Abstract In the present study, biosorption behavior of a green filamentous alga, spirogyra in its native and modified states was investigated for copper removal from an electroplating industrial effluent. For this, the effluent containing 194 mg·L−1 Cu2+ in sulfate medium was contacted with both forms of spirogyra, under the parametric variations of effluent pH, adsorbent dosage, contact time, and sorption temperature. The study revealed spirogyra as a prominent candidate for removing contaminant metal cation; however, at the same condition, biosorption capacity of modified biomass in gel form was higher than the native spirogyra. At the optimized condition with 6 g sorbent dosage treated to 100 mL effluent for 30 min at pH 6.0 and temperature 20 °C, the maximum 82.8% and 96.4% copper could be adsorbed by the native and modified spirogyra, respectively. The batch sorption data using native biomass followed pseudo-first-order kinetic; exhibiting the multilayer sorption mechanism via surface diffusion could be defined by the Freundlich model. In contrast, the sulfuric acid treated modified spirogyra followed pseudo-second-order kinetics and intra particle diffusion as the rate-limiting step.

A study of kinetics and successive sorption/desorption of Zn and Cd uptake onto iron-modified zeolite

Clay Minerals ◽  
2015 ◽  
Vol 50 (1) ◽  
pp. 117-132 ◽  
Author(s):  
Marin Ugrina ◽  
Nediljka Vukojević Medvidović ◽  
Jelena Perić ◽  
Marina Trgo
Keyword(s):  
Electrolyte Solutions ◽  
Approximation Model ◽  
Diffusion Kinetic ◽  
Cd Uptake ◽  
Modified Zeolite ◽  
Rate Limiting Step ◽  
Intra Particle Diffusion ◽  
Rate Limiting ◽  
Kinetics Of ◽  
And Diffusion

AbstractThe sorption properties of iron-modified zeolite (IMZ) and the kinetics of zinc and cadmium uptake by the IMZ were investigated by the batch method. Two kinetic stages were observed, fast uptake up to 240 min, followed by slow uptake up to equilibrium. Kinetic results were fitted to the reaction and diffusion kinetic models, which indicated that intra-particle diffusion was the rate-limiting step. The Vermeulen’s approximation model was used to predict the quantity of Zn and Cd ions removed per gram of IMZ. The results of the successive sorption and desorption of Zn and Cd ions, with different electrolyte solutions, showed the best desorption efficiency with sodium salt solutions. Four successive repetitions of the sorption/desorption cycles showed a small difference between the amount of sorbed and desorbed Zn and Cd ions from the second to the fourth cycle. This indicates excellent sorption/regeneration properties of the IMZ.

Ornithine Decarboxylase Activity in Cultured Endothelial Cells Stimulated by Serum, Thrombin and Serotonin

1978 ◽  
Vol 39 (02) ◽  
pp. 496-503 ◽  
Author(s):  
P A D’Amore ◽  
H B Hechtman ◽  
D Shepro
Keyword(s):  
Endothelial Cells ◽  
Ornithine Decarboxylase ◽  
Decarboxylase Activity ◽  
Aortic Endothelial Cells ◽  
Ornithine Decarboxylase Activity ◽  
Rate Limiting Step ◽  
Bovine Aortic Endothelial Cells ◽  
Limiting Step ◽  
Rate Limiting ◽  
Serum Serotonin

SummaryOrnithine decarboxylase (ODC) activity, the rate-limiting step in the synthesis of polyamines, can be demonstrated in cultured, bovine, aortic endothelial cells (EC). Serum, serotonin and thrombin produce a rise in ODC activity. The serotonin-induced ODC activity is significantly blocked by imipramine (10-5 M) or Lilly 11 0140 (10-6M). Preincubation of EC with these blockers together almost completely depresses the 5-HT-stimulated ODC activity. These observations suggest a manner by which platelets may maintain EC structural and metabolic soundness.

Dynamics of hepatic and peripheral insulin effects suggest common rate-limiting step in vivo

Diabetes ◽  
1993 ◽  
Vol 42 (2) ◽  
pp. 296-306 ◽  
Author(s):  
D. C. Bradley ◽  
R. A. Poulin ◽  
R. N. Bergman
Keyword(s):  
Rate Limiting Step ◽  
Limiting Step ◽  
Rate Limiting

Cobalt/Lewis Acid Catalysis for Hydrocarbofunctionalization of Alkynes via Cooperative C–H Activation

2020 ◽  
Author(s):  
Chang-Sheng Wang ◽  
Sabrina Monaco ◽  
Anh Ngoc Thai ◽  
Md. Shafiqur Rahman ◽  
Chen Wang ◽  
...  
Keyword(s):  
Catalytic System ◽  
Lewis Acid ◽  
Hydrogen Transfer ◽  
Acid Catalysis ◽  
Rate Limiting Step ◽  
Site Selectivity ◽  
Set Up ◽  
Site Selective ◽  
First Time ◽  
Rate Limiting

A catalytic system comprised of a cobalt-diphosphine complex and a Lewis acid (LA) such as AlMe3 has been found to promote hydrocarbofunctionalization reactions of alkynes with Lewis basic and electron-deficient substrates such as formamides, pyridones, pyridines, and azole derivatives through site-selective C-H activation. Compared with known Ni/LA catalytic system for analogous transformations, the present catalytic system not only feature convenient set up using inexpensive and bench-stable precatalyst and ligand such as Co(acac)3 and 1,3-bis(diphenylphosphino)propane (dppp), but also display distinct site-selectivity toward C-H activation of pyridone and pyridine derivatives. In particular, a completely C4-selective alkenylation of pyridine has been achieved for the first time. Mechanistic stidies including DFT calculations on the Co/Al-catalyzed addition of formamide to alkyne have suggested that the reaction involves cleavage of the carbamoyl C-H bond as the rate-limiting step, which proceeds through a ligand-to-ligand hydrogen transfer (LLHT) mechanism leading to an alkyl(carbamoyl)cobalt intermediate.

Sign in / Sign up

Export Citation Format

Share Document