Nitriding of High Speed Steel for Improvement of Tools Resistance

The article is devoted to the study of the gas nitriding process, which makes it possible to obtain high-quality diffusion layers in high-speed steel M2 on the basis of an internal nitriding zone without a brittle nitride zone. The results of studies of the nitrided steel phase composition with a change of the saturating atmosphere during dilution of ammonia by hydrogen are presented. An increase in the resistance of the nitrided tool when drilling structural steel is shown, which is associated with the dispersion hardening of the internal nitriding zone with tungsten nitrides.

Effect of magnesium on some mechanical properties of 1200 Aluminium alloy

This paper investigated the effect of magnesium as a dispersion strengthening material on some mechanical properties of 1200-Aluminium (Al-Fe-Si) alloy, a typical commercial aluminium alloy used in the production of household utensils. 1200-Aluminium (Al-Fe-Si) alloy containing varying percentages of the dispersion hardening material (i.e. Magnesium) were produced and mechanical tests namely; hardness, tensile strength and impact strength were carried out. Also, the microstructures of the cast materials were studied. The results showed that increase in magnesium content, as dispersion hardening material improved the hardness, tensile strength and caused a slight decrease in impact strength of the 1200-Aluminium alloy. It is inferred from this work that using magnesium as a dispersion hardening material brings about corresponding improvement in some mechanical properties of 1200-Aluminium (Al-Fe-Si) alloy. Keywords: Magnesium, Aluminium alloy, dispersion strengthened, reinforced alloy, crystallographic formation Depth, Geothermal Energy

The Influence of Friction Deformation on the Microstructure and Hardening of Beryllium Bronze

The peculiarities of the microstructure and properties of BrBNT1.7 beryllium bronze tape samples were studied: the samples were subjected to dispersion hardening as a result of quenching in a supersaturated solid solution and aging. Friction deformation in a dry friction mode provides additional effective hardening while maintaining increased plasticity (bending-and-unbending test).

The Effect of Tungsten Nanoparticles on the Hardness of Sintered Sn-Cu-Co-W Alloys

The effect of tungsten nanoparticles and microparticles on the structure and hardness of sintered Sn–Cu–Co–W alloys has been studied. Tungsten powder of 19–24 μm sized particles was milled in a planetary-centrifugal mill, after which the size of particles was 25 nm to 20 μm. The milled and non-milled tungsten was then mixed with powders of tin, copper and cobalt. The specimens were compacted in moulds and sintered in vacuum at 820°C for 20 minutes. The structure of sintered materials was studied using X-ray diffraction analysis and scanning electron microscopy. Microhardness (HV0.01) of structural constituents and hardness of the materials were measured. It has been determined that it is alloys containing mechanically milled tungsten that have the highest hardness. The main factor influencing the rise of hardness is dispersion hardening with nanoparticles. A further factor is work hardening of tungsten microparticles during ball milling. The highest hardness of 109–111 HRB has been obtained in the Sn–Cu–Co–W alloy containing 23% wt. of milled tungsten, with the proportion of tin, copper and cobalt being 1/2.6/1.6.

Microstructure and mechanical properties of high-manganese-containing high-speed twin-roll cast Al-Mn-Si alloy strips and their cold-rolled sheets

Al-Mn based alloys with high-manganese content are expected to have improved mechanical properties due to solid solution hardening and/or dispersion hardening. However, the increase of Mn solubility of the alloy is difficult by using the conventional DC casting. In order to solve this problem, in the present study, we focused on the twin-roll casting method which is characterized by high cooling rates. Several kinds of high Mn-containing Al-Mn-Si alloy strips were fabricated by using a vertical-type high-speed twin-roll caster equipped with a pair of water-cooled copper rolls. Direct temperature measurement of the liquid melt during the casting was also performed. The alloy strips of various compositions containing up to 4 Mn and 2 Si (wt%) were successfully obtained. By observing the microstructure of the cross section of the strip, we found the characteristic solidified structure. The solidified structure consisted of three layers. Two solidified shells with a columnar dendrite structure grew from the roll surfaces toward the strip center. In the mid-thickness region, the band structure consisting of equiaxed dendrites and globular grains was observed between the solidified shells. Very fine primary particles were observed in the matrix near the strip surface, while, relatively coarse particles with blocky and needle-like shape were observed in the central band of the as-cast strip. The electric conductivity measurement was performed for the as-cast strips. Mn solubility in Al matrix was estimated from the obtained values. The estimated Mn solubility in the Al-2Mn-xSi strips was between 1.5 ~ 1.8wt% Mn. It was over 1.43wt%Mn for the Al-4Mn-xSi strips. We found that the Mn solubility of the as-cast strips was considerably high. The strips were cold-rolled to the sheets and then annealed at various conditions. They were subjected to the tensile tests, and the effects of solid solution hardening and dispersion hardening are discussed.