scholarly journals Effect of magnesium on some mechanical properties of 1200 Aluminium alloy

2021 ◽  
Vol 23 (2) ◽  
pp. 147-152
Author(s):  
M. D. Shittu ◽  
A. E. Olaniyi ◽  
A. A. Daniyan ◽  
D. A Isadare ◽  
K. M. Oluwasegun ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Aluminium Alloy ◽  
Magnesium Content ◽  
Mechanical Tests ◽  
Dispersion Hardening ◽  
Dispersion Strengthening ◽  
Hardening Material ◽  
Commercial Aluminium

This paper investigated the effect of magnesium as a dispersion strengthening material on some mechanical properties of 1200-Aluminium (Al-Fe-Si) alloy, a typical commercial aluminium alloy used in the production of household utensils. 1200-Aluminium (Al-Fe-Si) alloy containing varying percentages of the dispersion hardening material (i.e. Magnesium) were produced and mechanical tests namely; hardness, tensile strength and impact strength were carried out. Also, the microstructures of the cast materials were studied. The results showed that increase in magnesium content, as dispersion hardening material improved the hardness, tensile strength and caused a slight decrease in impact strength of the 1200-Aluminium alloy. It is inferred from this work that using magnesium as a dispersion hardening material brings about corresponding improvement in some mechanical properties of 1200-Aluminium (Al-Fe-Si) alloy. Keywords: Magnesium, Aluminium alloy, dispersion strengthened, reinforced alloy, crystallographic formation Depth, Geothermal Energy

scholarly journals Studying Some Mechanical Properties of River Shell Particle Polymer Matrix Composite

2019 ◽  
Vol 54 (4) ◽  
Author(s):  
Hamid M. Mahan ◽  
Malia M. Farhan ◽  
Thaer G. Shaalan
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Composite Material ◽  
Composite Materials ◽  
Impact Strength ◽  
Polymer Matrix ◽  
Unsaturated Polyester ◽  
Mechanical Tests ◽  
Polymer Matrix Composite ◽  
Shell Particles

This paper concerns developing the mechanical properties of unsaturated polyester. This work involves preparing a composite material and reinforcing it using river shell particles with volume fractures of (5%, 10%, 15%, 20%, 25%). The composite materials undergone mechanical tests with regard to hardness, tensile, and impact strength. The experimental results obtained show that the addition of river shell particles reduce the original tensile strength and impact strength up to 5% wt, while the hardness is increased with increasing addition of river shell particles percent.

Microstructural and Mechanical Behaviour of Aluminium Matrix Composites Reinforced with Coated SiC Particles Fabricated by Stir Casting

2015 ◽  
Vol 766-767 ◽  
pp. 301-307 ◽  
Author(s):  
S. Dhanalakshmi ◽  
M. Jaivignesh ◽  
A. Suresh Babu ◽  
K. Shanmuga Sundaram
Keyword(s):  
Mechanical Properties ◽  
Silicon Carbide ◽  
Tensile Strength ◽  
Impact Strength ◽  
Aluminium Alloy ◽  
Metal Matrix Composites ◽  
Metal Matrix ◽  
Base Alloy ◽  
Stir Casting ◽  
Matrix Composites

Metal matrix composites are the resultant of combination of two or more elements or compounds, possessing enhanced characteristics than the individual constituents present in them. This paper deals with the fabrication of Al 2014-SiC composite and investigation of its Microstructure and Mechanical properties. 2014 Aluminium alloy is characterized by good hardness. It is selected as the base metal. The Silicon Carbide is characterized by good strength and low density (3.21 g/cm3). It is chosen as the reinforcement. Silicon Carbide is coated with Nickel by electroless method to increase its wettability and binding properties. The fabrication of metal matrix composites is done by stir casting in a furnace, by introducing the required quantities of reinforcement into molten Aluminium alloy. The reinforcement and alloy is mixed by means of stirring, with the help of a stirrer. The base alloy and the composites are then tested for mechanical properties such as tensile strength, flexural strength, impact strength and hardness. The fabricated samples have higher tensile strength and impact strength than the alloy. Microstructure of the samples, are analyzed using optical microscope.

scholarly journals Effect of Different Variants of Heat Treatment on Mechanical Properties of the AlSi17CuNiMg Alloy

2016 ◽  
Vol 16 (2) ◽  
pp. 41-44 ◽  
Author(s):  
A. Jarco ◽  
J. Pezda
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Impact Strength ◽  
High Hardness ◽  
Dispersion Hardening ◽  
Initial State ◽  
Plastic Properties ◽  
Fourfold Increase ◽  
The Impact

Abstract Dispersion hardening, as the main heat treatment of silumins having additions of copper and magnesium, results in considerable increase of tensile strength and hardness, with simultaneous decrease of ductility of the alloy. In the paper is presented an attempt of introduction of heat treatment operation consisting in homogenizing treatment prior operation of the dispersion hardening, to minimize negative effects of the T6 heat treatment on plastic properties of hypereutectoidal AlSi17CuNiMg alloy. Tests of the mechanical properties were performed on a test pieces poured in standardized metal moulds. Parameters of different variants of the heat treatment, i.e. temperature and time of soaking for individual operations were selected basing on the ATD (Thermal Derivation Analysis) diagram and analysis of literature. The homogenizing treatment significantly improves ductility of the alloy, resulting in a threefold increase of the elongation and more than fourfold increase of the impact strength in comparison with initial state of the alloy. Moreover, the hardness and the tensile strength (Rm) of the alloy decrease considerably. On the other hand, combination of the homogenizing and dispersion hardening enables increase of elongation with about 40%, and increase of the impact strength with about 25%, comparing with these values after the T6 treatment, maintaining high hardness and slight increase of the tensile strength, comparing with the alloy after the dispersion hardening.

Effect of silver nitrate on some mechanical properties of heat polymerizing acrylic resins

2019 ◽  
Vol 14 (1) ◽  
pp. 110
Author(s):  
Assiss. Prof. Dr. Sabiha Mahdi Mahdi ◽  
Dr. Firas Abd K. Abd K.
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Silver Nitrate ◽  
Surface Hardness ◽  
Mechanical Tests ◽  
Hardness Tester ◽  
Acrylic Resins ◽  
The Difference

Aim: The aimed study was to evaluate the influence of silver nitrate on surfacehardness and tensile strength of acrylic resins.Materials and methods: A total of 60 specimens were made from heat polymerizingresins. Two mechanical tests were utilized (surface hardness and tensile strength)and 4 experimental groups according to the concentration of silver nitrate used.The specimens without the use of silver nitrate were considered as control. Fortensile strength, all specimens were subjected to force till fracture. For surfacehardness, the specimens were tested via a durometer hardness tester. Allspecimens data were analyzed via ANOVA and Tukey tests.Results: The addition of silver nitrate to acrylic resins reduced significantly thetensile strength. Statistically, highly significant differences were found among allgroups (P≤0.001). Also, the difference between control and experimental groupswas highly significant (P≤0.001). For surface hardness, the silver nitrate improvedthe surface hardness of acrylics. Highly significant differences were statisticallyobserved between control and 900 ppm group (P≤0.001); and among all groups(P≤0.001)with exception that no significant differences between control and150ppm; and between 150ppm and 900ppm groups(P>0.05).Conclusion: The addition of silver nitrate to acrylics reduced significantly the tensilestrength and improved slightly the surface hardness.

Mechanical Property Improvement of Poly(Butylene Succinate) by Reinforcing with Modified Fumed Silica

2014 ◽  
Vol 1025-1026 ◽  
pp. 215-220 ◽  
Author(s):  
Sasirada Weerasunthorn ◽  
Pranut Potiyaraj
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Fumed Silica ◽  
Tensile Modulus ◽  
Silica Particles ◽  
Melt Mixing ◽  
Butylene Succinate ◽  
Ir Spectrophotometry

Fumed silica particles (SiO2) were directly added into poly (butylene succinate) (PBS) by melt mixing process. The effects of amount of fumed silica particles on mechanical properties of PBS/fumed silica composites, those are tensile strength, tensile modulus, impact strength as well as flexural strength, were investigated. It was found that the mechanical properties decreased with increasing fumed silica loading (0-3 wt%). In order to increase polymer-filler interaction, fumed silica was treated with 3-glycidyloxypropyl trimethoxysilane (GPMS), and its structure was analyzed by FT-IR spectrophotometry. The PBS/modified was found to possess better tensile strength, tensile modulus, impact strength and flexural strength that those of PBS/fumed silica composites.

scholarly journals The Structure and Mechanical Properties of Hemp Fibers-Reinforced Poly(ε-Caprolactone) Composites Modified by Electron Beam Irradiation

2021 ◽  
Vol 11 (12) ◽  
pp. 5317
Author(s):  
Rafał Malinowski ◽  
Aneta Raszkowska-Kaczor ◽  
Krzysztof Moraczewski ◽  
Wojciech Głuszewski ◽  
Volodymyr Krasinskyi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Electron Beam ◽  
Impact Strength ◽  
Flexural Modulus ◽  
Natural Fibers ◽  
High Energy ◽  
Electron Radiation ◽  
Elongation At Break ◽  
Hemp Fibers

The need for the development of new biodegradable materials and modification of the properties the current ones possess has essentially increased in recent years. The aim of this study was the comparison of changes occurring in poly(ε-caprolactone) (PCL) due to its modification by high-energy electron beam derived from a linear electron accelerator, as well as the addition of natural fibers in the form of cut hemp fibers. Changes to the fibers structure in the obtained composites and the geometrical surface structure of sample fractures with the use of scanning electron microscopy were investigated. Moreover, the mechanical properties were examined, including tensile strength, elongation at break, flexural modulus and impact strength of the modified PCL. It was found that PCL, modified with hemp fibers and/or electron radiation, exhibited enhanced flexural modulus but the elongation at break and impact strength decreased. Depending on the electron radiation dose and the hemp fibers content, tensile strength decreased or increased. It was also found that hemp fibers caused greater changes to the mechanical properties of PCL than electron radiation. The prepared composites exhibited uniform distribution of the dispersed phase in the polymer matrix and adequate adhesion at the interface between the two components.

scholarly journals Effects of water absorption on the mechanical properties of hybrid natural fibre/phenol formaldehyde composites

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Sekar Sanjeevi ◽  
Vigneshwaran Shanmugam ◽  
Suresh Kumar ◽  
Velmurugan Ganesan ◽  
Gabriel Sas ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Water Absorption ◽  
Hybrid Composites ◽  
Phenol Formaldehyde ◽  
Natural Fibre ◽  
The Other ◽  
Fibre Reinforcement ◽  
Dry Conditions

AbstractThis investigation is carried out to understand the effects of water absorption on the mechanical properties of hybrid phenol formaldehyde (PF) composite fabricated with Areca Fine Fibres (AFFs) and Calotropis Gigantea Fibre (CGF). Hybrid CGF/AFF/PF composites were manufactured using the hand layup technique at varying weight percentages of fibre reinforcement (25, 35 and 45%). Hybrid composite having 35 wt.% showed better mechanical properties (tensile strength ca. 59 MPa, flexural strength ca. 73 MPa and impact strength 1.43 kJ/m2) under wet and dry conditions as compared to the other hybrid composites. In general, the inclusion of the fibres enhanced the mechanical properties of neat PF. Increase in the fibre content increased the water absorption, however, after 120 h of immersion, all the composites attained an equilibrium state.

Effect of Quaternary Ammonium-Modified Montmorillonites on Mechanical Properties of Polypropylene

1998 ◽  
Vol 520 ◽  
Author(s):  
Y. H. Zhang ◽  
K. C. Gong
Keyword(s):  
Mechanical Properties ◽  
Mechanical Property ◽  
Tensile Strength ◽  
Impact Strength ◽  
Quaternary Ammonium ◽  
Small Addition ◽  
Pp Composites ◽  
Addition Amount

ABSTRACTHybrids of quaternary ammonium-modified montmorillonites and polypropylene were prepared by melting intercalation. Results of mechanical property measurements show that, tensile strength, modulus and impact strength of PP composites are greatly enhanced simultaneously by a small addition amount of modified montmorillonites.

scholarly journals Experimental Evaluation of Mechanical Properties of Friction Welded Dissimilar Steels under Varying Axial Pressures

2016 ◽  
Vol 66 (1) ◽  
pp. 27-36 ◽  
Author(s):  
Amit Handa ◽  
Vikas Chawla
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Failure Analysis ◽  
Friction Welding ◽  
Experimental Evaluation ◽  
Micro Hardness ◽  
Aisi 304 ◽  
Torsional Strength ◽  
Hardness Values

AbstractThe present study emphasizes on joints two industrially important materials AISI 304 with AISI 1021steels, produced by friction welding have been investigated. Samples were welded under different axial pressures ranging from 75MPa to 135MPa, at constant speed of 920rpm. The tensile strength, torsional strength, impact strength and micro hardness values of the weldments were determined and evaluated. Simultaneously the fractrography of the tensile tested specimens were carried out, so as to understand the failure analysis. It was observed that improved mechanical properties were noticed at higher axial pressures. Ductile failures of weldments were also observed at 120MPa and 135MPa axial pressures during fractography analysis.

Effect of Wood Filler Concentration on Physical and Mechanical Properties of PLA-Based Composites

2021 ◽  
Vol 887 ◽  
pp. 110-115
Author(s):  
G.A. Sabirova ◽  
R.R. Safin ◽  
N.R. Galyavetdinov
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Composite Materials ◽  
Impact Strength ◽  
Wood Flour ◽  
Experimental Studies ◽  
Physical And Mechanical Properties ◽  
Filler Concentration ◽  
High Concentration

This paper presents the findings of experimental studies of the physical and mechanical properties of wood-filled composites based on polylactide (PLA) and vegetable filler in the form of wood flour (WF) thermally modified at 200-240 °C. It also reveals the dependence of the tensile strength, impact strength, bending elastic modulus, and density of composites on the amount of wood filler and the temperature of its thermal pre-modification. We established that an increase in the concentration of the introduced filler and the degree of its heat treatment results in a decrease of the tensile strength, impact strength and density of composite materials, while with a lower binder content, thermal modification at 200 °C has a positive effect on bending elastic modulus. We also found that 40 % content of a wood filler heated to 200 °C is sufficient to maintain relatively high physical and mechanical properties of composite materials. With a higher content of a wood filler, the cost can be reduced but the quality of products made of this material may significantly deteriorate. However, depending on the application and the life cycle of this product, it is possible to develop a formulation that includes a high concentration of filler.

Sign in / Sign up

Export Citation Format

Share Document