Influence of the Precursor, Molarity and Temperature on the Rheology and Structural Buildup of Alkali-Activated Materials

This study presents an investigation of the effects of the precursor, alkalinity and temperature on the rheology and structural buildup of alkali activated materials. Here, 100% fly ash, 100% slag and blended mixes of fly ash and slag were activated by 4 M, 6 M, 8 M or 10 M (only for sodium hydroxide) solutions at 25 °C, 35 °C, 45 °C and 55 °C. The rheological properties were investigated to obtain the flow curves, viscosity, storage modulus, and loss factor of these materials. The results showed that for the presence of slag, a higher molarity of the alkali activating solution and a high temperature all caused greater interparticle force, leading to an increase in the shear stress and viscosity of the alkali activated materials. It was also observed that slag had the greatest effect on the increase in the storage modulus of the blended mixes. Furthermore, the higher alkalinity and temperature levels were instrumental in initiating the dissolution of fly ash and improving its rate of structural buildup. Moreover, the interdependence of various factors showed that the type of precursor, as well as the concentration of alkali activating solution, were the primary influencing factors on the polymerization process, as well as the rheological measurements of alkali-activated materials.

Analytical and Optimization Study of Propagation and Reduction of Wave in Granular Sand by DEM Method

In this research, the discrete element method has been used to analyze wave propagation and to investigate the factors affecting wave reduction in granular soils. The method of discrete elements is important because of the possibility of preparing completely similar specimens and examining the effect of changes in a certain parameter on the Behavior of the specimens. This method also provides an understanding of the changes that have occurred at the micro-scale of granular materials that are not achievable with other laboratory and numerical methods. To model the specimens, a set of disks with specific granulation has been used for two-dimensional studies. PFC 2D software has been used to perform simulations and related analyzes such as interparticle force. The DEM code in MATLAB is used to check the wave depreciation. In this research, the optimization process was performed using experimental data and the Taguchi method using the DEM method. The results of this study show that there is a direct relationship between the number of particle set contacts and the wave propagation speed. Also, material properties such as particle density are the most important parameters affecting wave velocity. The results of the method (DEM) are done with PFC 2D software and a comparison between the results of this method with the solution methods used by other researchers is shown to be a good match.

Research on the Formation Mechanism of Loess Vertical Joints

The popular occurrence of vertical joints in loess formation aggravates the anisotropism of loess and contributes to various geohazards (e.g., slope failures and soil erosion). To alleviate the geohazards caused by the vertical joints, researches need to be carried out to investigate the formation mechanism of these vertical joints. However, the theoretical analysis of the vertical joints’ formation mechanism is limited up to now. In this study, we conducted a laboratory column experiment to observe joint development. Furthermore, using the unsaturated soil theory, we proposed a theoretical model to investigate the tensile stress that contributes to the formation of the loess vertical joint. In the experiment, the air-dried and crushed soil was sifted into the column, which simulates the free fall deposition process of the natural loess in China and contributes to a uniform state. 2500 ml of water was added at the top of the column. The topsoil experienced a wetting-drying process. During desaturation, 9 similar vertical joints were developed with similar horizontal distance. A theoretical model that calculates the interparticle force or tensile force between two adjacent particles was proposed based on the force balance equations. The theoretical model elucidates the phenomena in a laboratory experiment well and provides an insight into the formation mechanism of vertical joints in a uniform soil. The results highlight the generation of vertical joints in the initial deposition stage of loess with a uniform particle arrangement. Besides, the tensile force that contributes to the joint formation arises from the matric suction and surface tension of the solid-water-air contractile film.

Homogenization of the 1D Peri-static/dynamic Bar with Triangular Micromodulus

In peridynamics, boundary effects generally appear due to nonlocality of interparticle forces; in particular, end effects are found in 1D bars. In a previous work by Eriksson and Stenström (J Peridyn Nonlocal Model 2(2):205–228, 2020), a simple method to remove end effects in certain types of 1D bars, or to homogenize such bars, was presented for bars with constant micromodulus. In this work, which is a continuation of Eriksson and Stenström (J Peridyn Nonlocal Model 2(2):205–228, 2020), the homogenizing procedure is applied to bars with a linear, or “triangular,” micromodulus. For the examples studied, common in practice, the linear elastic behavior of a homogenized bar, is identical to that of a corresponding classical continuum mechanics bar, independently of the interparticle force range and total number of material points of the bar.

The influence of packing structure and interparticle forces on ultrasound transmission in granular media

Ultrasound propagation through externally stressed, disordered granular materials was experimentally and numerically investigated. Experiments employed piezoelectric transducers to excite and detect longitudinal ultrasound waves of various frequencies traveling through randomly packed sapphire spheres subjected to uniaxial compression. The experiments featured in situ X-ray tomography and diffraction measurements of contact fabric, particle kinematics, average per-particle stress tensors, and interparticle forces. The experimentally measured packing configuration and inferred interparticle forces at different sample stresses were used to construct spring networks characterized by Hessian and damping matrices. The ultrasound responses of these network were simulated to investigate the origins of wave velocity, acoustic paths, dispersion, and attenuation. Results revealed that both packing structure and interparticle force heterogeneity played an important role in controlling wave velocity and dispersion, while packing structure alone quantitatively explained most of the observed wave attenuation. This research provides insight into time- and frequency-domain features of wave propagation in randomly packed granular materials, shedding light on the fundamental mechanisms controlling wave velocities, dispersion, and attenuation in such systems.