Physical and mechanical properties of mortars containing date palm fibers

This paper presents the results of a study conducted to investigate the effects of incorporating Sefri Date Palm Leave Fibers (SDPLF) into the mortar. A total of seven mixtures were prepared and tested. SDPLF were collected from local farms. The fibers were then cleaned, dried, and cut to different sizes of 10 mm, 20 mm, and 50 mm, maintaining the same individual fiber width of approximately 5±2 mm. The content of SDPLF in mortars was kept to 1% and 3% by mass. The physical and mechanical properties of SDPLF fibers and SDPLF mortars were investigated. The compressive strength at 7, 14, and 28 days was determined. The water absorption rate test was carried out on mortars containing 1% SDPLF fibers. The results showed that mortars with SDPLF have lower workability, lower density, and lower compressive strength as compared to control mortars. However, they are still acceptable for use in construction works. Mortars containing 10 mm and 20 mm SDPLF fibers by mass showed significant improvement in terms of water absorption rate as compared to the control mortar.

Investigation of the mechanical and thermal characteristics of an eco-insulating material made of plaster and date palm fibers

The negative impact of the production and use of building materials on the environment has become evident, so in recent decades, to find more sustainable, eco-friendly, and low-cost materials, the last research tends to reconsider the use of natural fibers and traditional building materials. This paper aims to develop a bio-composite based on the southern Algerian region's local materials consisting mainly of plaster and waste from date palm trees. Many properties were examined experimentally through previous research of our team (physical, mechanical, and microstructure characteristics) [1, 2] to characterize these materials. Several samples of bio-composite of plaster configurations with short length (20mm) and eight-weight ratios (0.5% - 4%) of palm fibers were prepared for mechanical, thermal, and physical characterizations. In addition, tested all previous properties on the specimens after 28 days of curing in normal conditions. The results show a clear improvement in the bio-composites mechanical performance (an increase in the bending strength with achieving compressive strength) and their thermal properties, which have been well developed (density, thermal conductivity, and specific heat capacity). To enhance the resistance of palm fibers to chemical degradation in the plaster's alkaline environment and improve the adhesion between them, these fibers were treated with a NaOH solution of 1% concentration. The plaster's composites reinforced with date palm fibers can be qualified as eco-friendly and thermal insulation building materials.

Nanocrystalline Cellulose from Microcrystalline Cellulose of Date Palm Fibers as a Promising Candidate for Bio-Nanocomposites: Isolation and Characterization

Date palm fiber (Phoenix dactylifera L.) is a natural biopolymer rich in lignocellulosic components. Its high cellulose content lends them to the extraction of tiny particles like microcrystalline cellulose (MCC) and nanocrystalline cellulose (NCC). These cellulose-derived small size particles can be used as an alternative biomaterial in wide fields of application due to their renewability and sustainability. In the present work, NCC (A) and NCC (B) were isolated from date palm MCC at 60 min and 90 min hydrolysis times, respectively. The isolated NCC product was subjected to characterization to study their properties differences. With the hydrolysis treatment, the yields of produced NCC could be attained at between 22% and 25%. The infrared-ray functional analysis also revealed the isolated NCC possessed a highly exposed cellulose compartment with minimized lignoresidues of lignin and hemicellulose. From morphology evaluation, the nanoparticles’ size was decreased gradually from NCC (A) (7.51 nm width, 139.91 nm length) to NCC (B) (4.34 nm width, 111.51 nm length) as a result of fragmentation into cellulose fibrils. The crystallinity index was found increasing from NCC (A) to NCC (B). With 90 min hydrolysis time, NCC (B) showed the highest crystallinity index of 71% due to its great cellulose rigidity. For thermal analysis, NCC (B) also exhibited stable heat resistance, in associating with its highly crystalline cellulose structure. In conclusion, the NCC isolated from date palm MCC would be a promising biomaterial for various applications such as biomedical and food packaging applications.

Elaboration and characterization of extruded clay bricks with light weight date palm fibers

Construction materials used in arid zones in Algeria are mainly concrete and clay bricks. These materials are not suitable for this climate as they have poor insulating properties. In order to improve thermal comfort in buildings and to save energy, materials used in construction must be good insulators while having an acceptable mechanical strength. New extruded clay bricks have been developed by incorporating date palm fibers into the clay matrix. These are considered renewable and are abundant agricultural waste generated by date palm trees each year without exploitation. Starting from the composition usually used by the local brickyard, seven compositions were tested, with clay/fiber ratios from 80 %/0 % to 68 %/12 %, by considering as a constant the sum of the masses (clay and fiber), with the percentage of dune sand maintained as equal to 20 wt.-%. From experiment tests it was observed that for a composition with 68 wt.-% clay, 20 wt.-% dune sand and 12 wt.-% fiber, the bricks prepared were light weight, had good thermal properties and met compressive strength requirements. For this composition the weight reduction exceeded 23 % for an energy saving impact of more than 44 % in a dry state.