Simplified Colloidal Method to Produce Nanostructured Au-Ag Films with Superconductivity in the Ambient

This article presents a detailed synthetic strategy to enable preparation of Au-Ag structures with optical and electrical anomalies

Simplified Colloidal Method to Produce Nanostructured Au-Ag Films with Superconductivity in the Ambient

This article presents a detailed synthetic strategy to enable preparation of Au-Ag structures with optical and electrical anomalies

Composite Fe3O4-MXene-Carbon Nanotube Electrodes for Supercapacitors Prepared Using the New Colloidal Method

MXenes, such as Ti3C2Tx, are promising materials for electrodes of supercapacitors (SCs). Colloidal techniques have potential for the fabrication of advanced Ti3C2Tx composites with high areal capacitance (CS). This paper reports the fabrication of Ti3C2TX-Fe3O4-multiwalled carbon nanotube (CNT) electrodes, which show CS of 5.52 F cm−2 in the negative potential range in 0.5 M Na2SO4 electrolyte. Good capacitive performance is achieved at a mass loading of 35 mg cm−2 due to the use of Celestine blue (CB) as a co-dispersant for individual materials. The mechanisms of CB adsorption on Ti3C2TX, Fe3O4, and CNTs and their electrostatic co-dispersion are discussed. The comparison of the capacitive behavior of Ti3C2TX-Fe3O4-CNT electrodes with Ti3C2TX-CNT and Fe3O4-CNT electrodes for the same active mass, electrode thickness and CNT content reveals a synergistic effect of the individual capacitive materials, which is observed due to the use of CB. The high CS of Ti3C2TX-Fe3O4-CNT composites makes them promising materials for application in negative electrodes of asymmetric SC devices.

Synthesis of ZnAl2O4 and Evaluation of the Response in Propane Atmospheres of Pellets and Thick Films Manufactured with Powders of the Oxide

ZnAl2O4 nanoparticles were synthesized employing a colloidal method. The oxide powders were obtained at 300 °C, and their crystalline phase was corroborated by X-ray diffraction. The composition and chemical structure of the ZnAl2O4 was carried out by X-ray and photoelectron spectroscopy (XPS). The optical properties were studied by UV-vis spectroscopy, confirming that the ZnAl2O4 nanoparticles had a direct transition with bandgap energy of 3.2 eV. The oxide’s microstructures were microbars of ~18.2 nm in size (on average), as analyzed by scanning (SEM) and transmission (TEM) electron microscopies. Dynamic and stationary gas detection tests were performed in controlled propane atmospheres, obtaining variations concerning the concentration of the test gas and the operating temperature. The optimum temperatures for detecting propane concentrations were 200 and 300 °C. In the static test results, the ZnAl2O4 showed increases in propane response since changes in the material’s electrical conductance were recorded (conductance = 1/electrical resistance, Ω). The increases were ~2.8 at 200 °C and ~7.8 at 300 °C. The yield shown by the ZnAl2O4 nanoparticles for detecting propane concentrations was optimal compared to other similar oxides categorized as potential gas sensors.

Highly Selective Au/ZnO via Colloidal Deposition for CO2 Hydrogenation to Methanol: Evidence of AuZn Role

Gold, Au nanoparticles were deposited on ZnO, Al2O3, and Ga2O3 via colloidal method in order to investigate the role of support for CO2 hydrogenation to methanol. Au/ZnO was also produced using impregnation method to investigate the effect of colloidal method to improve methanol selectivity. Au/ZnO produced via sol immobilization showed high selectivity towards methanol meanwhile impregnation method produced Au/ZnO catalyst with high selectivity towards CO. The CO2 conversion was also influenced by the amount of Au weight loading. Au nanoparticles with average diameter of 3.5 nm exhibited 4% of CO2 conversion with 72% of methanol selectivity at 250 °C and 20 bar. The formation of AuZn alloy was identified as active sites for selective CO2 hydrogenation to methanol. Segregation of Zn from ZnO to form AuZn alloy increased the number of surface oxygen vacancy for CO2 adsorption to form formate intermediates. The formate was stabilized on AuZn alloy for further hydrogenation to form methanol. The use of Al2O3 and Ga2O3 inhibited the formation of Au alloy, and therefore reduced methanol production. Au/Al2O3 showed 77% selectivity to methane, meanwhile Au/Ga2O3 produced 100% selectivity towards CO. Copyright © 2021 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0).

Hydrogenation of benzene and toluene over supported rhodium and rhodium-gold catalysts

Rhodium and rhodium-gold catalysts supported on amorphous aluminosilicates (ASA), titanium dioxide (rutile, TiO2) was prepared in two different ways: absorption and colloidal method. The catalysts were characterized by an inductively coupled plasma optical emission spectrometer (ICP-OES), transmission electron microscopy (TEM) and X-ray diffraction (XRD). The activity and selectivity of the prepared catalysts were tested by the hydrogenation of benzene and toluene. Hydrogenation was conducted at a pressure of 4 MPa and a temperature 80 °C. The bimetallic Rh-Au/ASA catalyst prepared by the absorption method showed higher activity and selectivity in benzene hydrogenation reaction, the same catalyst prepared by the colloidal method demonstrated lower selectivity.