Review on Steel Enhancement for Nuclear RPVs

The reactor pressure vessel (RPV) is one of the most important elements of a nuclear power plant (NPP). The RPV determines the plant operational lifetime since it is not replaceable economically. The purpose of the RPV steel study and enhancement to increase the NPP’s (Nuclear Power Plants) operation lifetime from the original 30–40 years up to 60–80 years or even beyond. The RPV lifetime limited by ageing of the RPV steels. RPV ageing highly depends on the main environmental effects: fast neutron radiation, thermal effects causing thermal ageing and low-cycle fatigue. Firstly, the chemical composition via aged mechanical properties was studied. Efforts to increase the toughness against the radiation embrittlement was enhanced by the appearance of the modern microstructural testing devices such as APFIM (atom probe field ion microscopy), SANS (small-angle neutron scattering) positron annihilation spectroscopy (PAS), transmission electron microscopy (TEM) and Mössbauer spectroscopy (MS). The information on the effect of alloying and polluting elements for the microstructure allowed us to produce increased ageing toughness of the RPVs, and to enhance the safety and lifetime calculations of them, supporting long-term safe operation (LTO).

Source for In Situ Positron Annihilation Spectroscopy of Thermal—And Hydrogen-Induced Defects Based on the Cu-64 Isotope

This work aims to investigate the 64Cu isotope applicability for positron annihilation experiments in in situ mode. We determined appropriate characteristics of this isotope for defect studies and implemented them under aggressive conditions (i.e., elevated temperature, hydrogen environment) in situ to determine the sensitivity of this approach to thermal vacancies and hydrogen-induced defects investigation. Titanium samples were used as test materials. The source was obtained by the activation of copper foil in the thermal neutron flux of a research nuclear reactor. Main spectrometric characteristics (e.g., the total number of counts, fraction of good signals, peak-to-noise ratio) of this source, as well as line-shaped parameters of the Doppler broadening spectrum (DBS), were studied experimentally. These characteristics for 64Cu (in contrast to positron sources with longer half-life) were shown to vary strongly with time, owing to the rapidly changing activity. These changes are predictable and should be considered in the analysis of experimental data to reveal information about the defect structure. The investigation of samples with a controlled density of defects revealed the suitability of 64Cu positron source with an activity of 2–40 MBq for defects studies by DBS. However, greater isotope activity could also be applied. The results of testing this source at high temperatures and in hydrogen atmosphere showed its suitability to thermal vacancies and hydrogen-induced defects studies in situ. The greatest changes in the defect structure of titanium alloy during high-temperature hydrogen saturation occurred at the cooling stage, when the formation of hydrides began, and were associated with an increase in the dislocation density.

Effects of He-D Interaction on Irradiation-Induced Swelling in Fe9Cr Alloys

The atomic-scale defects such as (deuterium, helium)-vacancy clusters in nuclear energy materials are one of the causes for the deterioration of the macroscopic properties of materials. Unfortunately, they cannot be observed by transmission electron microscopy (TEM) before they grow to the nanometer scale. Positron annihilation spectroscopy (PAS) has been proven to be sensitive to open-volume defects, and could characterize the evolution of the size and concentration of the vacancy-like nanoclusters. We have investigated the effects of He-D interaction on the formation of nanoscale cavities in Fe9Cr alloys by PAS and TEM. The results show that small-sized bubbles are formed in the specimen irradiated with 5 × 1016 He+/cm2, and the subsequent implanted D-ions contribute to the growth of these helium bubbles. The most likely reason is that helium bubbles previously formed in the sample captured deuterium injected later, causing bubbles to grow. In the lower dose He-irradiated samples, a large number of small dislocations and vacancies are generated and form helium-vacancy clusters with the helium atoms.

High-density magnetic-vacancy inclusion in Co2MnGa single crystal probed by spin-polarized positron annihilation spectroscopy

Co2MnGa is a Weyl semimetal exhibiting giant anomalous Hall and Nernst effects. Using spin-polarized positron annihilation spectroscopy, we examined a Bridgman-grown Co2MnGa single crystal with a nearly perfect L21-ordered structure and a reference Co2MnAl polycrystal with a Mn-Al-disordered B2 structure. We found that a large amount of magnetic vacancies (more than 100 ppm) were included in the Co2MnGa crystal but not the Co2MnAl crystal. We discuss possible reasons for the inclusion of vacancies, the role of vacancies in the development of the ordered structure, and the electronic states associated with the vacancies. Towards the development of Co2MnGa-based devices, the manners for reducing vacancies as well as the influence of vacancies on the electrical transport properties should be considered.

On the Limitations of Positron Annihilation Spectroscopy in the Investigation of Ion-Implanted FeCr Samples

New materials for advanced fission/fusion nuclear facilities must inevitably demonstrate resistance to radiation embrittlement. Thermal and radiation ageing accompanied by stress corrosion cracking are dominant effects that limit the operational condition and safe lifetime of the newest nuclear facilities. To study these phenomena and improve the current understanding of various aspects of radiation embrittlement, ion bombardment experiments are widely used as a surrogate for neutron irradiation. While avoiding the induced activity, typical for neutron-irradiated samples, is a clear benefit of the ion implantation, the shallow near-surface region of the modified materials may be a complication to the post-irradiation examination (PIE). However, microstructural defects induced by ion implantation can be effectively investigated using various spectroscopic techniques, including slow-positron beam spectroscopy. This method, typically represented by techniques of positron annihilation lifetime spectroscopy and Doppler broadening spectroscopy, enables a unique depth-profile characterisation of the near-surface region affected by ion bombardment or corrosion degradation. One of the best slow-positron beam facilities is available at the pulsed low-energy positron system (PLEPS), operated at FRM-II reactor in Munich (Germany). Bulk studies (such as high energy ion implantation or neutron irradiation experiments) can be, on the other hand, effectively performed using radioisotope positron sources. In this paper, we outline some basics of the two approaches and provide some recommendations to improve the validity of the positron annihilation spectroscopy (PAS) data obtained on ion-irradiated samples using a conventional 22Na positron source.

Gradient Microstructure Induced by Surface Mechanical Attrition Treatment in Grade 2 Titanium Studied Using Positron Annihilation Spectroscopy and Complementary Methods

Microstructural changes in grade 2 titanium generated by surface mechanical attrition treatment (SMAT) were studied using positron annihilation lifetime spectroscopy and complementary methods. A significant increase in the mean positron lifetime indicated many lattice defects introduced by SMAT. Two positron lifetime components were resolved in the positron lifetime spectra measured. The longer lifetime revealed the presence of vacancy clusters containing about 3 or 4 vacancies, while the shorter one was attributed to the annihilation of positrons trapped at dislocations. The changes of the positron lifetime indicated a decreasing dislocation density and the presence of a deeper layer with a higher concentration of vacancy clusters at the distance from the treated surface for which the microhardness approached the value for the strain-free matrix. Electrochemical impedance spectroscopy showed the positive effect of SMAT on the corrosion resistance of the titanium studied in a saline environment also after removal of the original oxide layer that was formed during the SMAT.