Water intake of cellulose materials monitored by positron annihilation lifetime spectroscopy

In this study, for the first time, the experimental technique of positron annihilation lifetime spectroscopy (PALS) has been applied to monitor in situ the microstructural changes of cellulose-based materials, i.e. paper, during water intake. For three different cellulose samples, bleached fine paper without filler, Kraft paper without filler, and a viscose fiber sheet, the mean positron lifetime $$\Delta \tau _{\mathrm {mean}}$$ Δ τ mean showed a strong increase with time in humid atmosphere, but exhibiting different trends depending on the type of sample. For all the cellulose samples investigated, the mean positron lifetime $$\Delta \tau _{\mathrm {mean}}$$ Δ τ mean shows an initial strong increase simultaneously occurring (t<10 h) to the mass increase of the samples due to water intake. Interestingly, the variations of $$\Delta \tau _{\mathrm {mean}}$$ Δ τ mean of the viscose fiber sheet and the Kraft paper sample both show a second increase on longer timescales (t>60 h in humid atmosphere) during which the mass increase of these samples has already been saturated. The results of this study show that by the means of PALS, water transport in paper can be reliably followed over a long timespan and it is even possible to distinguish between different types of cellulose materials. The second stage increase of the mean positron lifetime after long times in humid atmosphere for the Kraft paper sample and the pure viscose sheets even suggest that not only water intake itself can be monitored but also further atomistic processes in the material are accessible.

Temperature studies using positron lifetime spectroscopy of the subsurface zone in pure titanium exposed to a dry sliding test

The report presents the positron annihilation studies of subsurface zone generated in pure titanium exposed to a long period dry sliding test. The total depth of the subsurface zone induced is detected at about 250 µm. Only dislocations and vacancy clusters which consist of two or three vacancies are observed in this zone. Their concentration decreases with the depth, especially at the depth above 100 µm. Despite the long duration of the sliding test, no clear signs indicating the presence of a tribolayer were observed. This was confirmed also by observation of annealing of defects in this zone at different depths. The lack of the tribolayer is in contrast to the research done so far for other metals.

Analysis of Surface Properties of Nickel Alloy Elements Exposed to Impulse Shot Peening with the Use of Positron Annihilation

The paper presents the results of experimental studies on the impact of impulse shot peening parameters on surface roughness (Sa, Sz, Sp, Sv), surface layer microhardness, and the mean positron lifetime (τmean). In the study, samples made of the Inconel 718 nickel alloy were subjected to impulse shot peening on an originally designed stand. The variable factors of the experiment included the impact energy, the diameter of the peening element, and the number of impacts per unit area. The impulse shot peening resulted in changes in the surface structure and an increase in surface layer microhardness. After the application of impulse shot peening, the analyzed roughness parameters increased in relation to post-milling values. An increase in microhardness was obtained, i.e., from 27 HV 0.05 to 108 HV 0.05 at the surface, while the maximum increase the microhardness occur at the depth from 0.04 mm to 0.08 mm. The changes in the physical properties of the surface layer were accompanied by an increase in the mean positron lifetime τmean. This is probably related to the increased positron annihilation in point defects. In the case of small surface deformations, the increase in microhardness was accompanied by a much lower increase in τmean, which may indicate a different course of changes in the defect structure consisting mainly in modification of the dislocation system. The dependent variables were subjected to ANOVA analysis of variance (it was one-factor analysis), and the effect of independent variables was evaluated using post-hoc tests (Tukey test).

Gradient Microstructure Induced by Surface Mechanical Attrition Treatment in Grade 2 Titanium Studied Using Positron Annihilation Spectroscopy and Complementary Methods

Microstructural changes in grade 2 titanium generated by surface mechanical attrition treatment (SMAT) were studied using positron annihilation lifetime spectroscopy and complementary methods. A significant increase in the mean positron lifetime indicated many lattice defects introduced by SMAT. Two positron lifetime components were resolved in the positron lifetime spectra measured. The longer lifetime revealed the presence of vacancy clusters containing about 3 or 4 vacancies, while the shorter one was attributed to the annihilation of positrons trapped at dislocations. The changes of the positron lifetime indicated a decreasing dislocation density and the presence of a deeper layer with a higher concentration of vacancy clusters at the distance from the treated surface for which the microhardness approached the value for the strain-free matrix. Electrochemical impedance spectroscopy showed the positive effect of SMAT on the corrosion resistance of the titanium studied in a saline environment also after removal of the original oxide layer that was formed during the SMAT.

Positron annihilation in mordenite zeolite

The theoretical study of the positron annihilation in complex material such as zeolite is greatly significant to support and increase the accuracy analysis of the material structure from the experimental data of the positron annihilation. The mordenite zeolite is a big and complicated structure consisting of channels and cavities. The analysis of the mordenite structure is studied by the PALS so depending on the selection of the positron lifetime components of the positron annihilation spectra fitting methods. Therefore, these positron life times in on TO4, Na, Ca, K, Fe, H2O and the rings which form the channels and cavities are sophisticatedly studied by the DFT calculation using Ab-initio. The mordenite and modified mordenite zeolite structures are precisely analyzed, and the physical behaviors of the positron in these are more understood by these theoretical results.

Positron lifetime spectroscopy applied to pure Tellurium

High-purity crystalline Tellurium has been investigated using positron lifetime spectroscopy technique in order to determine basic information missing in the current experimental knowledge of the positron annihilation spectroscopy field. Three different pairs of samples have been studied in the as-received state and, in order to eliminate the vacancy-type defects, after consecutive isothermal treatments at 300 °C. Lifetime corresponding to the annihilation in the Tellurium bulk has been determined as 282(1) ps. Previous theoretical calculations present in the bibliography that used different methods and parameterization provided a wide range of values for the annihilation lifetime of the positron in the bulk of Tellurium. The obtained result has been used to identify the most accurate results among them.

Positron Annihilation Spectroscopy as a Diagnostic Tool for the Study of LiCoO2 Cathode of Lithium-Ion Batteries

Positron annihilation spectroscopy using lifetime and Doppler broadening allows the characterization of the lithiation state in LiCoO2 thin film used in cathode of lithium-ion batteries. The lifetime results reflect positron spillover because of the presence of graphite in between the oxide grains in real cathode Li-ion batteries. This spillover produces an effect in the measured positron parameters which are sensitive to delocalized electrons from lithium atoms as in Compton scattering results. The first component of the positron lifetime corresponds to a bulk-like state and can be used to characterize the state of charge of the cathode while the second component represents a surface state at the grain-graphite interface.

Positron lifetime spectroscopy of defect structures in Cd1–x Zn x Te mixed crystals grown by vertical Bridgman–Stockbarger method

Positron annihilation lifetime spectroscopy was used to examine grown-in defects in Cd1–x Zn x Te mixed crystals as a function of Zn content (x = 0, 0.07, 0.11, 0.49, 0.9, 0.95, 1) and measuring temperature. All samples were prepared using the high-pressure modified vertical Bridgman–Stockbarger method. The crystal structure and material phase were characterized by X-ray diffraction. The positron lifetime spectra reveal the presence of both open volumes and shallow traps regardless of the sample composition. In particular, both average and bulk lifetimes are found to be much higher in ternary alloys (CdZnTe) than those in binary systems (CdTe and ZnTe). This originates from distinct differences in average electron densities and the nature of open-volume defects between binary and ternary samples. Competition in positron trapping with increasing Zn content is observed between defects characteristic for both structural systems. Moreover, a clear correlation is shown between defects and the lattice thermal conductivity of studied samples. The applicability of the positron trapping model to CdTe-based materials is discussed.