additional thermal treatment
Recently Published Documents


TOTAL DOCUMENTS

16
(FIVE YEARS 0)

H-INDEX

4
(FIVE YEARS 0)

Author(s):  
Ulviyya Magsud Gurbanova ◽  
Dunya Mahammad Babanly ◽  
Ruhangiz Gurmuz Huseynova ◽  
Dilgam Babir Tagiyev

The process of co-deposition of Ni with Mo from alkaline electrolytes was studied by taking linear and cyclic polarization curves of Pt electrode at various concentrations of initial components and potential scan rates. Solutions of Na2MoO4∙2H2O and NiSO4∙7H2O were used as sources of ions of the main components in NH4OH electrolyte. It was found that co-deposition of nickel with molybdenum goes through the oxide formation stage, and a solid solution of these two metals is deposited on the cathode surface. The film obtained at constant current on Ni electrode under optimal conditions was found amorphous, but additional thermal treatment at 500 °C for one hour made it polycrystalline. This was confirmed by peaks in X-ray diffraction patterns, corresponding to NiMoO4, Ni, and MoO3. The proposed electrolyte and electrolysis conditions allow to obtain thin films with molybdenum content ranging from 17.1 to 50.9 at.%. The co-deposition of Ni with Mo is limited by diffusion of these ions to the cathode surface. The knowledge of the mechanism of co-deposition of Ni and Mo will make possible a selection of optimal conditions for deposition of alloys of the required composition with satisfactory electrocatalytic properties.



2019 ◽  
Vol 946 ◽  
pp. 374-379 ◽  
Author(s):  
Anatoly A. Babenko ◽  
Vladimir I. Zhuchkov ◽  
Natalia I. Selmenskih

Effects of boron in low-carbon tube steel grade 17G1SU on nonmetallic inclusions, structure and mechanical properties were investigated. Experimental samples of rolled metal containing boron 0.006 and 0.011% are characterized by predominantly small, nonmetallic inclusions not more than 5 μm, which are represented by complex alumomagnesium spinels in the shell of manganese and calcium sulfides, and small silicate inclusions. Nonmetallic inclusions of comparative pipe steel sample, containing no boron characterized by the presence of larger inclusions presented complex oxysulfide and sulfide films. The main structural component of the comparative and experimental samples is ferrite. The introduction of boron is contributed by a decrease in the average size of ferritic grains from 8.7 μm (0% B) to 6.2 (0.006% B). Increasing the boron content to 0.011% leads to slight increase (up to 6.8 microns) of the size. The mechanical properties of 10 μm rolled metal pipe steel ensured the production of rolled products of strength class X80 without additional (thermal) treatment, as a result of the reduction in the size and shape of nonmetallic inclusions, and formation of dispersed structure.



2018 ◽  
Vol 243 ◽  
pp. 00019
Author(s):  
Taras Dement ◽  
Irina Kurzina ◽  
Mark Kalashnikov ◽  
Natalia Popova ◽  
Natalia Karakchieva

Three-layer materials consisting of the V-4.9Ti-4.8Cr/ferrite steel 17Cr-12Ni-Fe /V-4.9Ti-4.8Cr were obtained in the paper. Phase composition and microstructure of the transition zone of the three-layer material of vanadium alloy V-4.9Ti-4.8Cr and ferrite steel 17Cr-12Ni-Fe were considered. The use of the method of direct laser growing allowed obtaining a three-layer material with qualitative interconnection of layers, as well as decreasing a multistage nature of deformation and thermal operations used when obtaining a three-layer material in earlier works. Additional thermal treatment of a three-layer alloy led to growth of matrix grains up to 100 μm of the vanadium alloy. A uniform distribution of main elements V, Ti, Cr was observed in the transition zone both before and after annealing. A zone of interdiffusion of the metals amounted to 250-350 μm.



Nukleonika ◽  
2017 ◽  
Vol 62 (2) ◽  
pp. 149-152 ◽  
Author(s):  
Bożena Malesa ◽  
Tomasz Pikula ◽  
Dariusz Oleszak ◽  
Elżbieta Jartych

Abstract In this research, the mechanical activation method is proposed as an alternative process of preparation of the (BiFeO3)1-x-(BaTiO3)x solid solutions with various concentrations of barium titanate (x = 0.1÷0.9). However, mechanical milling itself does not allow obtaining the desired products and additional thermal treatment is needed to complete the solid-state reaction. In the present studies, X-ray diffraction and 57Fe Mössbauer spectroscopy were applied as complementary methods in order to study the structural and magnetic properties of materials. The investigations revealed that an increase of BaTiO3 concentration causes changes in the crystalline and hyperfine magnetic structure of the studied (BiFeO3)1-x-(BaTiO3)x system.



2016 ◽  
Vol 843 ◽  
pp. 117-122
Author(s):  
P.L. Reznik ◽  
O.A. Chikova ◽  
B.V. Ovsyannikov

The article investigates the influence of additional thermal treatment of an ingot before deformation on the microstructure, phase composition, crystalline structure, and mechanical properties of flat hot deformed semi-finished products made from Al-Mg-Mn-Sc-Zr aluminum alloy and presents the results obtained. Additional thermal processing of ingots before deformation was carried out in order to increase the level of the mechanical properties of semiproducts. Mechanical properties testing was carried out for both large-sized specimens and for sub-micro volumes of α-aluminum crystalline particles.



2014 ◽  
Vol 1675 ◽  
pp. 129-136
Author(s):  
Sally A. Ibrahim ◽  
Svitlana Fialkova ◽  
Kwadwo Mensah-Darkwa ◽  
Sergey Yarmolenko ◽  
Dhananjay Kumar

ABSTRACTAs the need for smaller data storage devices in the market continues to grow, the study of new combinations of self-assembled magnetic nanoparticles/films is greatly needed. In this research, Fe50-Ni50 films were synthesized using a Pulsed Laser Deposition technique. The films were analyzed using scanning electron microscopy (SEM), atomic force microscopy (AFM) and physical properties measurement system (PPMS). Films were deposited from Fe-Ni alloy target (50%-50% composition), deposition was conducted in vacuum, at substrate temperatures varying from liquid nitrogen temperature -196°C to 600°C. The films were annealed in a vacuum chamber at 600°C for 1 hour. The study reveals that the substrate temperature has significant effect on the structure of the films and their magnetic properties. It was shown that additional thermal treatment improved the quality of films in terms of narrow grain size distribution. Magnetic properties were also found to improve significantly after post annealing process.



2013 ◽  
Vol 58 (3) ◽  
pp. 663-671 ◽  
Author(s):  
I. Dobosz ◽  
W. Gumowska ◽  
M. Czapkiewicz

Abstract The nanowires of Co66-Fe34 alloy were obtained in the process of the electrodeposition in the pores of alumina membrane. With the use of the X-ray diffraction analysis the structure of cobalt-iron alloy wires was determined. The wires have the regular Body Centred Cubic structure (BCC). The influence of membrane parameters, an external magnetic field, and the annealing temperature on the magnetic properties of alloy wires was investigated. The obtained nanowires show a high shape anisotropy in the direction perpendicular to the membrane surface of anodic alumina. It was found that the highest influence on the magnetic properties of the wires has their geometry (height, diameter, and the distance between them). The use of an external magnetic field directed perpendicular to the sample surface during the electrodeposition process and additional thermal treatment (annealing) causes a slight increase of the coercive field, remanence, and volume energy density.



2011 ◽  
Vol 233-235 ◽  
pp. 1468-1473 ◽  
Author(s):  
Jai Houng Leu ◽  
Ay Su ◽  
Z.M. Huang ◽  
Ying Chieh Liu ◽  
Chun Yuan Lin

A Ni metal form was used to carry the Ru catalyst to induce the hydrogen gas from the NaBH4solution. Results show the Ni material was replaced by Ru material. Ru has been coating twice or more to cover all the Ni metal form surface as possible. About 4% of the Ru catalyst plate shows higher hydrogen generation efficiency. Relative to the concentration of NaBH4solution, the 20 wt.% is consisted with the 4% of Ru catalyst plate. Additional thermal treatment between every coating process, the Ru material can be adhered tightly. Furthermore, adding a layer of plastic film on the Ru catalyst plate can maintain 79% of the generation efficiency after 17 cycles of generation.



2010 ◽  
Vol 638-642 ◽  
pp. 2604-2609 ◽  
Author(s):  
Marcin Knapiński ◽  
Bartosz Koczurkiewicz ◽  
Anna Kawałek ◽  
Henryk Dyja

The article presents the results of physical simulations of the process of rolling plates of steel in the strength category 350÷460MPa on the finishing stand of a reversing mill. The simulations were performed for three steel grades and final plate thicknesses 40mm. The purpose of the simulations was to select the conditions of plate deformation to obtain, directly after rolling, structure of material corresponding to the structure obtained from normalizing annealing. Thus, the simulations reflected the normalizing rolling process. The research carried out has allowed to elaborate the new technology of production of rolling plate without an additional thermal treatment like normalization. It allow to decrease a time and total cost of production for this sort of product.



2009 ◽  
Vol 152-153 ◽  
pp. 221-224 ◽  
Author(s):  
O.S. Ivanova ◽  
I.S. Edelman ◽  
R.D. Ivantsov ◽  
V. Zabluda ◽  
V. Zaikovskiy ◽  
...  

Nano-composite structures based on potassium-aluminum-germanium glasses doped simultaneously with Fe and rare earth (RE) oxides - Gd, Tb, Dy, Ho, or Yb were studied for the first time. Samples were fabricated by glass technology and subjected to an additional thermal treatment at different regimes. Formation of magnetic nanoparticles was revealed with transmission electron microscope. Morphology and space distribution of nanoparticles in the glasses as well as optical and magneto optical spectra have been shown to be dependent on the additional treatment regime and almost independent of the type of the rare earth element.



Sign in / Sign up

Export Citation Format

Share Document