Effect of Splitter Blades on Performances of a Very Low Specific Speed Pump

The usage of splitter blades to enhance the performances of low specific speed pumps is common practice. Based on experimental and numerical studies, the influence of the addition of one and two splitter blades is investigated on a very low specific speed pump to assess their impact not only on the performance characteristics but also on the losses in all pump domains. First, the main characteristic curves are discussed and it is shown that the usage of splitter blades enhances the head of the pump while not impairing its efficiency. Secondly, a detailed analysis of the losses in the pump reveals that splitter blades improve the flow in all parts of the pumps, but the volute. The flow at the impeller outlet shows that splitter blades largely benefit the slip factor and discharges a more blade-congruent flow in the volute. However, higher absolute velocity at the outlet of the impeller with splitter blades increases friction at the volute wall, as confirmed by the average wall shear stress in the different tested cases.

Simulation analysis of aneurysm embolization surgery: Hemorheology of aneurysms with different embolization rates (CTA)

BACKGROUND: Embolization degree acts as an important factor affecting recurrence of aneurysm. OBJECTIVE: To analyze the role of hemodynamics parameters of different degrees of embolization in the occurrence, development and post-treatment of aneurysms, and to determine the specific factors causing the occurrence and recurrence of aneurysms after hemodynamics treatment. Our study provides a theoretical basis for the prevention and treatment of aneurysms. METHODS: Computed Tomography Angiography (CTA) data of a patient with cerebral aneurysm were used to model 0%, 24%, 52%, 84% and 100% of endovascular embolization, respectively. The time average wall shear stress, time average wall shear stress, oscillatory shear index, hemodynamics formation index and relative retentive time were used to analyze the changes of hemodynamics indexes in different embolic models. RESULTS: With the increase of embolic rate, the values of time average wall shear stress, time average wall shear stress grade and aneurysm index formation gradually increased, and the values of relative retention time gradually decreased. Oscillatory shear index was higher in patients with incomplete embolization and decreased in patients with complete embolization. CONCLUSIONS: As the degree of embolization increased, the blood flow tended to stabilize, reducing the risk of cerebral aneurysm rupture, and finding that the wall of the vessel junction was susceptible to injury.

Computational Study of the Blood Flow in Three Types of 3D Hollow Fiber Membrane Bundles

The goal of this study is to develop a computational fluid dynamics (CFD) modeling approach to better estimate the blood flow dynamics in the bundles of the hollow fiber membrane based medical devices (i.e., blood oxygenators, artificial lungs, and hemodialyzers). Three representative types of arrays, square, diagonal, and random with the porosity value of 0.55, were studied. In addition, a 3D array with the same porosity was studied. The flow fields between the individual fibers in these arrays at selected Reynolds numbers (Re) were simulated with CFD modeling. Hemolysis is not significant in the fiber bundles but the platelet activation may be essential. For each type of array, the average wall shear stress is linearly proportional to the Re. For the same Re but different arrays, the average wall shear stress also exhibits a linear dependency on the pressure difference across arrays, while Darcy's law prescribes a power-law relationship, therefore, underestimating the shear stress level. For the same Re, the average wall shear stress of the diagonal array is approximately 3.1, 1.8, and 2.0 times larger than that of the square, random, and 3D arrays, respectively. A coefficient C is suggested to correlate the CFD predicted data with the analytical solution, and C is 1.16, 1.51, and 2.05 for the square, random, and diagonal arrays in this paper, respectively. It is worth noting that C is strongly dependent on the array geometrical properties, whereas it is weakly dependent on the flow field. Additionally, the 3D fiber bundle simulation results show that the three-dimensional effect is not negligible. Specifically, velocity and shear stress distribution can vary significantly along the fiber axial direction.

Preliminary Computational Hemodynamics Study of Double Aortic Aneurysms under Multistage Surgical Procedures: An Idealised Model Study

Double aortic aneurysm (DAA) falls under the category of multiple aortic aneurysms. Repair is generally done through staged surgery due to low invasiveness. In this approach, one aneurysm is cured per operation. Therefore, two operations are required for DAA. However, post-first-surgery rupture cases have been reported. Although the problems involved with managing staged surgery have been discussed for more than 30 years, investigation from a hemodynamic perspective has not been attempted. Hence, this is the first computational fluid dynamics approach to the DAA problem. Three idealized geometries were prepared: presurgery, thoracic aortic aneurysm (TAA) cured, and abdominal aortic aneurysm (AAA) cured. By applying identical boundary conditions for flow rate and pressure, the Navier-Stokes equation and continuity equations were solved under the Newtonian fluid assumption. Average pressure in TAA was increased by AAA repair. On the other hand, average pressure in AAA was decreased after TAA repair. Average wall shear stress was decreased at the peak in post-first-surgery models. However, the wave profile of TAA average wall shear stress was changed in the late systole phase after AAA repair. Since the average wall shear stress in the post-first-surgery models decreased and pressure at TAA after AAA repair increased, the TAA might be treated first to prevent rupture.

Setup and Validation of Flow Cell Systems for Biofouling Simulation in Industrial Settings

A biofouling simulation system consisting of a flow cell and a recirculation tank was used. The fluid circulates at a flow rate of 350 L⋅ h−1in a semicircular flow cell with hydraulic diameter of 18.3 mm, corresponding to an average velocity of 0.275 m⋅ s−1. Using computational fluid dynamics for flow simulation, an average wall shear stress of 0.4 Pa was predicted. The validity of the numerical simulations was visually confirmed by inorganic deposit formation (using kaolin particles) and also by direct observation of pathlines of tracer PVC particles using streak photography. Furthermore, the validity of chemostat assumptions was verified by residence time analysis. The system was used to assess the influence of the dilution rate on biofilm formation byEscherichia coliJM109(DE3). Two dilution rates of 0.013 and 0.0043 h−1were tested and the results show that the planktonic cell concentration is increased at the lower dilution rate and that no significant changes were detected on the amount of biofilm formed in both conditions.

A New Probe for Measurement of Velocity and Wall Shear Stress in Unsteady, Reversing Flow

Separated turbulent flows exhibit instantaneous reversals of flow direction which make measurement of the velocity field extremely difficult. A three-wire heat-tracer technique has been employed to measure streamwise velocity of a low-speed air flow very near a smooth, solid wall; the wall shear stress is calculated using a similarity hypothesis. Initial results presented show the evolution of average wall shear stress and rms fluctuation intensity of wall shear stress in a reattaching 2-D flow downstream of a backward-facing step.