Rheology, Hydration, and Microstructure of Portland Cement Pastes Produced with Ground Açaí Fibers

Açaí (Euterpe oleracea) is a Brazilian typical fruit that is enveloped by natural fibers. This work investigated the effect of incorporating ground açaí fibers (in natura and chemically treated with NaOH and HCl) in 5–10 wt.% replacement of Portland cement on the rheology, hydration, and microstructure of pastes. Rotational rheometry, isothermal calorimetry, X-Ray Diffraction (XRD), and Scanning Electron Microscopy (SEM) were performed to evaluate the cement pastes, in addition to SEM-EDS, FTIR, zeta potential, and XRD for fiber characterization. The results showed that the chemical treatment reduced the cellulose and lignin contents in açaí fibers while increasing its surface roughness. The addition of 5% of either fiber slightly increased the yield stress and viscosity of paste, while 10% addition drastically increased these properties, reaching yield stress and viscosity values respectively 40 and 8 times higher than those of plain paste. The incorporation of 5% in natura fibers delayed the cement hydration by about 2.5 days while 10% in natura fibers delayed it by over 160 h. The chemical treatment significantly reduced this retarding effect, leading to a 3 h delay when 5% treated fibers were incorporated. Overall, the combined NaOH/HCl treatment was effective for açaí fibers functionalization and these fibers can be used in cementitious composites.

Application of WGM Resonances to the Measurement of the Temperature Increment of Ho and Ho-Yb Doped Optical Fibers Pumped at 1125 and 975 nm

Optical fiber characterization using whispering gallery mode resonances of the fiber itself has been demonstrated to be a powerful technique. In this work, we exploit the thermal sensitivity of whispering gallery mode resonances to characterize the pump-induced temperature increment in holmium doped and holmium-ytterbium codoped optical fibers. The technique relies on the measurement of the resonances’ wavelength shift due to temperature variation as a function of the pump power. Holmium doped fibers were pumped to the second excited level 5I6 of the Ho3+ ion using a laser diode at 1125 nm and ytterbium-holmium codoped fibers to the 2F5/2 level of the Yb3+ ion by a laser diode at 975 nm. Our results demonstrate that pumping ytterbium-holmium codoped fibers at 975 nm results in dramatic thermal effects, producing a temperature increment two orders higher than that observed in holmium doped fibers pumped with a 1125 nm laser diode.

Refractive-Index Profile Reconstruction in Graded-Index Polymer Optical Fibers Using Raman Spectroscopy

This work reports a novel method to create a 3D map of the refractive index of different graded-index polymer optical fibers (GI-POF), measuring the Raman spectra at different points of their transverse sections. Raman fingerprints provide accurate molecular information of the sample with high spatial resolution. The refractive index of GI-POFs is modified by adding a dopant in the preform; therefore, by recording the intensities of the Raman peaks related to the dopant material, a 3D map of the refractive index is rendered. In order to demonstrate the usefulness of the method, three different GI-POFs were characterized and the obtained results were compared with the information provided by the manufacturers. The results show accurate 3D maps of the refractive index taken in the actual GI-POF end faces, showing different imperfections that manufacturers do not take into account, such as the slight deviations of the azimuthal symmetry. The simplicity and the feasibility of the technique mean this method has high potential for fiber characterization purposes.

Synthesis of TiO2/WO3 Composite Nanofibers by a Water-Based Electrospinning Process and Their Application in Photocatalysis

TiO2/WO3 nanofibers were prepared in a one-step process by electrospinning. Titanium(IV) bis(ammonium lactato)dihydroxide (TiBALDH) and ammonium metatungstate (AMT) were used as water-soluble Ti and W precursors, respectively. Polyvinylpyrrolidone (PVP) and varying ratios of TiBALDH and AMT were dissolved in a mixture of H2O, EtOH and CH3COOH. The as-spun fibers were then heated in air at 1 °C min−1 until 600 °C to form TiO2/WO3 composite nanofibers. Fiber characterization was done using TG/DTA, SEM–EDX, FTIR, XRD, and Raman. The annealed composite nanofibers had a diameter range of 130–1940 nm, and the results showed a growth in the fiber diameter with an increasing amount of WO3. The photocatalytic property of the fibers was also checked for methyl orange bleaching in visible and UV light. In visible light, the photocatalytic activity increased with an increase in the ratio of AMT, while 50% TiBALDH composite fibers showed the highest activity among the as-prepared fibers in UV light.