Production of quicklime from Ashaka limestone through calcination process

This study is on the production of quicklime from Ashaka limestone through calcination process. Effects of temperature, particle size and time on quicklime yield were determined. The experiment was carried out at temperatures of 800, 900, 1000, 1100 and 1200 0C, particle sizes of 80mm, 90mm, 100mm, 300mm and 425mm and times of 0.5hr, 1hr, 2hrs, 3hrs and 4hrs. Analyses of the results showed that quicklime was successfully produced from Ashaka limestone through the calcination process. Quadratic model adequately described the relationship between quicklime yield and calcination factors of temperature, particle size and time. Recorded model F-value of 134.35 implies that the model is significant. The predicted R² of 0.9597 is in reasonable agreement with the adjusted R² of 0.9844; the difference is less than the critical value of 0.2. Optimum yield of 73.48% was obtained at optima operating conditions; temperature of 1000 0C, particle size of 90 µm and time of 3 hrs.

The synthesis of polyhydroxyalkanoates from low carbon wastewater under anaerobic-microaerobic process: effects of pH and nitrogen and phosphorus limitation

Polyhydroxyalkanoate (PHA) is a new type of bio-polyester which is expected to replace traditional petroleum-based plastics. The experiment was carried out based on anaerobic-microaerobic process. Firstly, the PHA accumulation capacity of activated sludge under different pH conditions was discussed, and then the batch test of nitrogen and phosphorus limitation was carried out under the condition of optimal pH. Moreover, the content of PHA monomer under nutrient restriction was also studied. The experimental results showed that when pH was not controlled (7.5~8.5), C:N and C:P weight ratio was equal to 150, the maximum content of PHA accounted for 50.39% and 36.07% of the dry cell weight, respectively. Besides, it was found that increasing the C:N weight ratio was beneficial to increasing the proportion of polyhydroxyvalerate (PHV) monomer in PHA.

Impact of Innovative Information Technologies and Systems on Achieving Financial and Process Effects of a Company

In the last decade, measuring the effectiveness and the effects of information and communication technologies has become a very important issue for companies. Company managers often argue over the effects achieved by integrating innovative information technologies and systems.

C. elegans feed yolk to their young in a form of primitive lactation

The nematode Caenorhabditis elegans exhibits rapid senescence that is promoted by the insulin/IGF-1 signalling (IIS) pathway via regulated processes that are poorly understood. IIS also promotes production of yolk for egg provisioning, which in post-reproductive animals continues in an apparently futile fashion, supported by destructive repurposing of intestinal biomass that contributes to senescence. Here we show that post-reproductive mothers vent yolk which can be consumed by larvae and promotes their growth. This implies that later yolk production is not futile; instead vented yolk functions similarly to milk. Moreover, yolk venting is promoted by IIS. These findings suggest that a self-destructive, lactation-like process effects resource transfer from postreproductive C. elegans mothers to offspring, in a fashion reminiscent of semelparous organisms that reproduce in a single, suicidal burst. That this process is promoted by IIS provides insights into how and why IIS shortens lifespan in C. elegans.

Effects of additives on via filling and pattern plating with simultaneous electroplating

Purpose The purpose of this paper is to solve the issue of via filling and pattern plating simultaneously by concentration optimization of accelerator and leveler in the electroplating bath. Design/methodology/approach This paper designs a series of experiments to verify the performance of pattern plating with the via filling plating formula. Then the compositions of electroplating solution are optimized to achieve via filling and pattern plating simultaneously. Finally, the mechanism of co-plating for via and line is discussed in brief. Findings To achieve excellent performance for via filling and pattern plating simultaneously, proportion of additives are comprehensively considered in optimization of electroplating process. Effects of additives on the via filling and pattern plating should be taken into consideration, especially in achieving flat lines. Originality/value This paper discusses the different effects of accelerator and leveler on the via filling and the pattern plating, respectively. The process of co-plating for the via and the line is presented. The superfilling of via and the flat line are simultaneously obtained with the optimized via filling formula.

Supercritical Assisted Production of Lutein-Loaded Liposomes and Modelling of Drug Release

In this work, a lipophilic ophthalmic drug, lutein, has been entrapped in liposomes, using a supercritical assisted process. Effects of pressure, temperature, and drug to lipid ratio variation were studied on mean diameters and lutein encapsulation efficiency. Liposomes with diameters between 153 ± 38 and 267 ± 56 nm were produced, and lutein encapsulation efficiencies between 86.5 ± 0.4% and 97.8 ± 1.2% were obtained. A Scanning Electron Microscope confirmed spherical shape and mean dimensions of vesicles. The variation of temperature for the production of liposomes showed a significant impact on lutein retention time in the double lipidic layer. Lutein drug release from liposomes produced at 35 °C ended in almost 4.5 days; whereas, liposomes produced at 40 °C showed a faster lutein release in 3 days; then, vesicles obtained at 45 °C released their lutein content in only 2 days. Drug release raw data were well-fitted using Weibull model (R2 up to 99%).