LES and Hybrid RANS/LES of a Fundamental Trailing Edge Slot

2014 ◽  
Author(s):  
Elizaveta Ivanova ◽  
Gregory M. Laskowski
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Numerical Study ◽  
Mixing Layer ◽  
Detached Eddy Simulation ◽  
Trailing Edge ◽  
Adiabatic Wall ◽  
Mean Velocity ◽  
Eddy Simulation ◽  
Delayed Detached Eddy Simulation

This paper presents the results of a numerical study on the predictive capabilities of Large Eddy Simulation (LES) and hybrid RANS/LES methods for heat transfer, mean velocity, and turbulence in a fundamental trailing edge slot. The geometry represents a landless slot (two-dimensional wall jet) with adjustable slot lip thickness. The reference experimental data taken from the publications of Kacker and Whitelaw [1] [2] [3] [4] contains the adiabatic wall effectiveness together with the velocity and the Reynolds-stress profiles for various blowing ratios and slot lip thicknesses. The simulations were conducted at three different lip thickness and several blowing ratio values. The comparison with the experimental data shows a general advantage of LES and hybrid RANS/LES methods against unsteady RANS. The predictive capability of the tested LES models (dynamic ksgs-equation [5] and WALE [6]) was comparable. The Improved Delayed Detached Eddy Simulation (IDDES) hybrid method [7] also shows satisfactory agreement with the experimental data. In addition to the described baseline investigations, the influence of the inlet turbulence boundary conditions and their implication for the initial mixing layer and heat transfer development were studied for both LES and IDDES.

Experimental and Numerical Investigations of the Heat Transfer and Flow Field in a Trailing Edge Cooling Geometry: Part 2 — LES and Hybrid RANS/LES Study

2015 ◽  
Author(s):  
Elizaveta Ivanova ◽  
Gustavo Ledezma ◽  
Guanghua Wang ◽  
Gregory M. Laskowski
Keyword(s):  
Heat Transfer ◽  
Numerical Study ◽  
Future Research ◽  
Detached Eddy Simulation ◽  
Trailing Edge ◽  
Validation Data ◽  
Eddy Simulation ◽  
Delayed Detached Eddy Simulation ◽  
Adiabatic Cooling ◽  
Les Model

This paper presents the results of a numerical study on the predictive capabilities of Large Eddy Simulation (LES) and hybrid RANS/LES methods for heat transfer in the trailing edge (TE) geometry experimentally investigated in Part 1. The experimental validation data includes 2D wall contours and laterally-averaged values of adiabatic cooling effectiveness. The simulations were conducted at three different blowing ratio values. The comparison with the experimental data shows a general advantage of LES and hybrid RANS/LES methods against steady-state RANS. The results obtained by means of the WALE LES model and the Improved Delayed Detached Eddy Simulation (IDDES) hybrid RANS/LES method were comparable. The presented grid dependence study shows the importance of adequate grid resolution for the predictive capabilities of trailing edge cooling LES. Furthermore, the importance of considering TE slot lands simulation quality in the numerical method assessment is discussed. Potential directions of future research needed to improve simulation reliability are outlined.

Numerical study of the flow over the modified simple frigate shape

2020 ◽  
pp. 095441002097775
Author(s):  
Tong Li ◽  
Yibin Wang ◽  
Ning Zhao
Keyword(s):  
Bluff Body ◽  
Recirculation Zone ◽  
Numerical Study ◽  
Reference Value ◽  
Flow Fields ◽  
Navier Stokes ◽  
Detached Eddy Simulation ◽  
Eddy Simulation ◽  
Delayed Detached Eddy Simulation ◽  
Simulation Results

The simple frigate shape (SFS) as defined by The Technical Co-operative Program (TTCP), is a simplified model of the frigate, which helps to investigate the basic flow fields of a frigate. In this paper, the flow fields of the different modified SFS models, consisting of a bluff body superstructure and the deck, were numerically studied. A parametric study was conducted by varying both the superstructure length L and width B to investigate the recirculation zone behind the hangar. The size and the position of the recirculation zones were compared between different models. The numerical simulation results show that the size and the location of the recirculation zone are significantly affected by the superstructure length and width. The results obtained by Reynolds-averaged Navier-Stokes method were also compared well with both the time averaged Improved Delayed Detached-Eddy Simulation results and the experimental data. In addition, by varying the model size and inflow velocity, various flow fields were numerically studied, which indicated that the changing of Reynolds number has tiny effect on the variation of the dimensionless size of the recirculation zone. The results in this study have certain reference value for the design of the frigate superstructure.

A numerical study of snow accumulation on the bogies of high-speed trains based on coupling improved delayed detached eddy simulation and discrete phase model

2018 ◽  
Vol 233 (7) ◽  
pp. 715-730 ◽  
Author(s):  
Mingyang Liu ◽  
Jiabin Wang ◽  
Huifen Zhu ◽  
Sinisa Krajnovic ◽  
Guangjun Gao
Keyword(s):  
High Speed ◽  
Numerical Study ◽  
Snow Accumulation ◽  
Phase Model ◽  
Detached Eddy Simulation ◽  
Discrete Phase Model ◽  
Eddy Simulation ◽  
Delayed Detached Eddy Simulation ◽  
Flow Mechanisms ◽  
Discrete Phase

A numerical simulation method based on the improved delayed detached eddy simulation coupled with a discrete phase model is used to study the influence of the snow on the performance of bogies of a high-speed train running in snowy weather. The snow particle trajectories, mass of snow packing on the bogie, and thickness of snow accumulation have been analyzed to investigate the flow mechanisms of snow accumulation on different parts of the bogies. The results show that the snow accumulation on the first bogie of the head vehicle is almost the same as that of the second bogie, but the total accumulated snow on the top side of the second bogie is more than 74% higher than that of the first bogie. Among all the components of the bogies, the motors were found to be strongly influenced by the snow accumulation. The underlying flow mechanisms responsible for the snow accumulations are discussed.

Combination of DES and DDES with a Correlation Based Transition Model

2013 ◽  
Vol 444-445 ◽  
pp. 374-379 ◽  
Author(s):  
Lei Qiao ◽  
Jun Qiang Bai ◽  
Jun Hua ◽  
Chen Wang
Keyword(s):  
Present Article ◽  
Test Case ◽  
Transition Model ◽  
Detached Eddy Simulation ◽  
Combined Model ◽  
Trailing Edge ◽  
Eddy Simulation ◽  
Delayed Detached Eddy Simulation ◽  
Stall Angle ◽  
Edge Separation

The present article describes the combination of the correlation based transition model of Menter et al. with the Detached Eddy Simulation (DES) and Delayed Detached Eddy Simulation (DDES) methodology. The interaction between transition model and DES or DDES method was investigated by T3A test case. The grid sensitivity of the combined methodology is discussed and the resolution is given. Then, the simulation of flow over foil of medium thick at stall angle was performed. The combined methodology produce results that have better agreement with experiment comparing to RANS transition model or fully turbulent DES/DDES alone. And the DDES based combined model shows a better agreement with experiment in the simulation of trailing edge separation comparing to DES based combined model.

scholarly journals Effects of inlet velocity profiles for thermal stripping phenomena in T-junctions

2021 ◽  
Vol 2116 (1) ◽  
pp. 012026
Author(s):  
Lisa Lampunio ◽  
Yu Duan ◽  
Raad Issa ◽  
Matthew D. Eaton
Keyword(s):  
Velocity Profiles ◽  
Lower Sensitivity ◽  
Detached Eddy Simulation ◽  
Mean Velocity ◽  
Inlet Velocity ◽  
Eddy Simulation ◽  
Delayed Detached Eddy Simulation ◽  
Flow Domain ◽  
The Mean ◽  
Good Agreement

Abstract This paper investigates the effects of different inlet velocities on thermal stripping phenomena within a T-junction. The computational flow domain is modelled using the Improved Delayed Detached Eddy Simulation (IDDES) turbulence model implemented within the commercial CFD code STAR-CCM+ 12.04. The computational model is validated against the OECD-NEA-Vattenfall T-junction Benchmark data. The influence of flat and fully developed inlet velocity profiles is then assessed. The results are in good agreement with the experimental data. The different inlet velocity profiles have a non-negligible effect on the mean wall temperature. The mean velocity shows lower sensitivity to changes in inlet velocity profiles, whose influence is confined mainly to the recirculation zone near the T-junction.

Numerical Study of a Compact Wavy Heat Exchanger

2011 ◽  
Author(s):  
Riccardo Mereu ◽  
Emanuela Colombo ◽  
Fabio Inzoli
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Nusselt Number ◽  
Numerical Study ◽  
Reynolds Numbers ◽  
Temperature Fields ◽  
Mean Velocity ◽  
Qualitative Comparison ◽  
Cross Sectional ◽  
Number Range

The present work deals with the design of compact wavy heat exchangers, where high values of heat transfer area per unit volume are looked for in order to reduce size and increase efficiency. A numerical investigation of a rectangular cross-sectional shape geometry, with duct aspect ratio of 7.3, and a corrugation angle of 145° is here proposed. The Reynolds numbers (based on the duct hydraulic diameter) range from 300 to 5000. The numerical analysis is performed by means of a finite volume commercial CFD code. Laminar and Unsteady Reynolds Averaged Navier-Stokes (U-RANS) approaches are applied to a three-dimensional fluid domain over a single module with periodic conditions, respectively for, lower (<1000) and higher (≥1000) Reynolds numbers. Mean velocity and temperature fields are obtained. The average values of Fanning friction factor and Nusselt number are compared with experimental data from literature for the same geometry operating at the same Reynolds number range. For the evaluation of heat transfer quantities obtained in the numerical study the analogy between Sherwood and Nusselt number is used. The numerical results agree with experimental data, by showing the capability of laminar and U-RANS two-equation approach, via RNG model, to capture the mean fluid flow including the Taylor-Gortler instability that appear at low Reynolds numbers. The qualitative comparison of heat results shows an agreement between experimental and numerical data, whereas the extension to quantitative comparison is limited by some deficiencies in experimental correlation for mass/heat transfer analogy.

Sign in / Sign up

Export Citation Format

Share Document