Tough Ductile Ultra High Strength Steels Through Direct Quenching and Partitioning—An Update

2018 ◽  
pp. 129-134
Author(s):  
Mahesh C. Somani ◽  
David A. Porter ◽  
Jukka I. Kömi ◽  
L. P. Karjalainen ◽  
Devesh K. Misra
Keyword(s):  
High Strength Steels ◽  
High Strength ◽  
Quenching And Partitioning ◽  
Direct Quenching ◽  
Ultra High Strength Steels

Innovation and Processing of Novel Tough Ductile Ultra-High Strength Steels through TMR-DQP Processing Route

2014 ◽  
Vol 783-786 ◽  
pp. 1009-1014 ◽  
Author(s):  
Mahesh C. Somani ◽  
David A. Porter ◽  
L. Pentti Karjalainen ◽  
Pasi Suikkanen ◽  
R.D.K. Misra
Keyword(s):  
Mechanical Properties ◽  
Physical Simulation ◽  
High Strength Steels ◽  
High Strength ◽  
Structural Steels ◽  
Processing Route ◽  
Quenching And Partitioning ◽  
Direct Quenching ◽  
Thermomechanical Rolling ◽  
Ultra High Strength Steels

Based on the recent concept of quenching and partitioning (Q&P), a novel TMR-DQP (thermomechanical rolling followed by direct quenching and partitioning) processing route has been established for the development of ultra-high strength structural steels with yield strengths ≈1100 MPa combined with good uniform and total elongations and impact toughness. Suitable compositions were designed based on high silicon and/or aluminium contents with or without small additions of Nb, Mo or Ni. The DQP parameters were established with the aid of physical simulation on a Gleeble simulator. Finally, the TMR-DQP processing route was designed for trials on a laboratory rolling mill. Metallographic studies showed that the desired martensite-austenite microstructures were achieved thus providing the targeted mechanical properties. The advantage of strained austenite in refining the martensite packets/blocks was clearly evident. No adverse effect of prolonged partitioning simulating the coiling stage has been noticed suggesting new possibilities for strip and plate products. Promising results in respect of microstructures and mechanical properties indicate that there are possibilities for developing tough ductile structural steels through the TMR-DQP route.

An Appraisal of Direct Quenching for the Development and Processing of Novel Super-High Strength Steels

2016 ◽  
Vol 879 ◽  
pp. 1819-1827 ◽  
Author(s):  
Mahesh C. Somani ◽  
Jaakko I. Hannula ◽  
Antti J. Kaijalainen ◽  
Devesh K. Misra ◽  
David A. Porter
Keyword(s):  
Linear Regression Analysis ◽  
High Strength Steels ◽  
High Strength ◽  
Processing Route ◽  
Low Carbon ◽  
Martensitic Steels ◽  
Quenching And Partitioning ◽  
Direct Quenching ◽  
Bainitic Steels ◽  
Novel Processing

Recent interests in developing novel super-high strength steels have led to extensive research efforts in direct quenching with or without tempering (DQ, DQT) or combined with partitioning (DQP). Both strip and plate products have been targeted for different applications. For boron-microalloyed DQ/DQT steels, the ASTM A255 approach for predicting the hardenability was considered inapplicable. Fresh attempts were made to develop new hardenability models through non-linear regression analysis by dynamically varying both the boron factor and multiplying factors of most elements in the alloy factor. Based on the recent concept of quenching and partitioning (Q&P), a novel processing route comprising thermomechanical rolling followed by direct quenching and partitioning (TMR-DQP) has been established for the development of ultra-high strength structural steels with yield strengths ≈1100 MPa combined with good uniform and total elongations and impact toughness. Examples of recent advances made in DQ processing and associated challenges, such as those related to the bendability of low carbon martensitic-bainitic steels and influence of boron on the toughness of Nb-bearing martensitic steels are presented.

The Multiphase Micro- and Nanostructures of 0.2 and 0.4 C Direct-Quenched and Partitioned Steels

2021 ◽  
Vol 1016 ◽  
pp. 1097-1102
Author(s):  
Sakari Pallaspuro ◽  
Ilkka Miettunen ◽  
S. Assa Aravindh ◽  
Sumit Ghosh ◽  
Wei Cao ◽  
...  
Keyword(s):  
Density Functional ◽  
High Strength Steels ◽  
High Strength ◽  
Density Functional Theory Calculations ◽  
Processing Route ◽  
Slow Cooling ◽  
Quenching And Partitioning ◽  
Main Research ◽  
Direct Quenching ◽  
Advanced High Strength Steels

Quenching and partitioning produces advanced high-strength steels that utilise transformation-induced plasticity for improved strength and deformability. Microstructures of these steels consist mainly of tempered martensite and carbon-enriched retained austenite. A novel processing route of direct-quenching and partitioning (DQP) facilitates carbon partitioning from supersaturated martensite to untransformed austenite directly from the quench-stop temperature in a decelerated cooling that simulates slow cooling of a coiled strip. A major advantage of DQP steels is that they keep both the costs and emissions down by inexpensive alloying and energy-efficient processing. In this study, we investigate the microstructures of 0.2C and 0.4C laboratory hot-rolled DQP steels with comparison to a direct-quenched variant with high-resolution transmission electron microscopy as the main research technique. We show that the structures of DQP steels have frequent nanotwinned regions and can contain three different crystal structures with characteristic length scales ranging from few nm to ~200 nm. This is in remarkable contrast to the traditional lath-martensitic microstructure of the as-quenched material. Density functional theory calculations provide further insight into these findings with the calculated results of energetics, and show that carbon helps in stabilising the newly found omega phase. These results give further insight to the aspects that must be considered when assessing their effect on essential mechanical properties like strain hardening and toughness.

Bendability and Microstructure of Direct Quenched Optim® 960QC

2014 ◽  
Vol 783-786 ◽  
pp. 818-824 ◽  
Author(s):  
Vili Kesti ◽  
A. Kaijalainen ◽  
A. Väisänen ◽  
A. Järvenpää ◽  
A. Määttä ◽  
...  
Keyword(s):  
Material Handling ◽  
High Strength Steels ◽  
High Strength ◽  
Total Elongation ◽  
Roll Forming ◽  
Direct Quenching ◽  
Thermomechanical Rolling ◽  
Ultra High Strength Steels ◽  
End Use ◽  
Save Energy

Use of ultra-high-strength steels (UHSS) in weight critical constructions is an effective way to save energy and minimize carbon footprint in the end use. On the other hand, the demands for reducing manufacturing costs and energy consumption of the steelmaker are increasing. This has led to development of energy efficient direct quenching (DQ) steelmaking process as an alternative to the conventional quenched and tempered or thermomechanical rolling and accelerate cooled processes. Ruukki has employed thermomechanical rolling and direct quenching process (TM + DQ) for a novel type of ultra-high-strength strip and plate steels since 2001. Advantages of the ultra-high-strength level (>900MPa) can be fully utilized only if fabricated properties are on a sufficient level. Bending is one of the most important workshop processes and a good bendability is essential for a structural steel. Hence, the metallurgy and bendability of Ruukki ́s TM + DQ strip steel Optim® 960QC have been investigated closely. It was found that by optimizing process parameters and chemical composition, a good combination of strength and ductility can be achieved by a modification of martensitic-bainitic microstructure. Despite of smaller total elongation, the bendability of Optim® 960QC is at least on the same level as on conventionally manufactured 960MPa steels. However, it is important to pay special attention to bending process (tool parameters, springback, bending force, material handling) when bending UHSS. It was also found that the bendability of Optim® 960QC can be significantly enhanced by local laser heat treatments or roll forming.

Texture analysis and joint performance of laser-welded similar and dissimilar dual-phase and complex-phase ultra-high-strength steels

2021 ◽  
Vol 174 ◽  
pp. 111035
Author(s):  
Ajit Kumar Pramanick ◽  
Hrishikesh Das ◽  
Ji-Woo Lee ◽  
Yeyoung Jung ◽  
Hoon-Hwe Cho ◽  
...  
Keyword(s):  
Texture Analysis ◽  
High Strength Steels ◽  
High Strength ◽  
Dual Phase ◽  
Complex Phase ◽  
Joint Performance ◽  
Ultra High Strength Steels

scholarly journals Carbon Redistribution and Microstructural Evolution Study during Two-Stage Quenching and Partitioning Process of High-Strength Steels by Modeling

Materials ◽  
2018 ◽  
Vol 11 (11) ◽  
pp. 2302 ◽  
Author(s):  
Yilin Wang ◽  
Huicheng Geng ◽  
Bin Zhu ◽  
Zijian Wang ◽  
Yisheng Zhang
Keyword(s):  
Retained Austenite ◽  
Volume Fraction ◽  
High Strength Steels ◽  
High Strength ◽  
Simulation Method ◽  
Low Carbon ◽  
Two Stage ◽  
Quenching And Partitioning ◽  
Carbon Redistribution ◽  
Carbon Martensite

The application of the quenching and partitioning (Q-P) process on advanced high-strength steels improves part ductility significantly with little decrease in strength. Moreover, the mechanical properties of high-strength steels can be further enhanced by the stepping-quenching-partitioning (S-Q-P) process. In this study, a two-stage quenching and partitioning (two-stage Q-P) process originating from the S-Q-P process of an advanced high-strength steel 30CrMnSi2Nb was analyzed by the simulation method, which consisted of two quenching processes and two partitioning processes. The carbon redistribution, interface migration, and phase transition during the two-stage Q-P process were investigated with different temperatures and partitioning times. The final microstructure of the material formed after the two-stage Q-P process was studied, as well as the volume fraction of the retained austenite. The simulation results indicate that a special microstructure can be obtained by appropriate parameters of the two-stage Q-P process. A mixed microstructure, characterized by alternating distribution of low carbon martensite laths, small-sized low-carbon martensite plates, retained austenite and high-carbon martensite plates, can be obtained. In addition, a peak value of the volume fraction of the stable retained austenite after the final quenching is obtained with proper partitioning time.

scholarly journals Effect of Quenching and Partitioning Temperatures in the Q-P Process on the Properties of AHSS with Various Amounts of Manganese and Silicon

2012 ◽  
Vol 706-709 ◽  
pp. 2734-2739 ◽  
Author(s):  
Hana Jirková ◽  
Ludmila Kučerová ◽  
Bohuslav Mašek
Keyword(s):  
Tensile Strength ◽  
Retained Austenite ◽  
Isothermal Holding ◽  
Bainitic Ferrite ◽  
High Strength Steels ◽  
High Strength ◽  
Experimental Program ◽  
Quenching Temperature ◽  
Quenching And Partitioning ◽  
Advanced High Strength Steels

The use of the combined influence of retained austenite and bainitic ferrite to improve strength and ductility has been known for many years from the treatment of multiphase steels. Recently, the very fine films of retained austenite along the martensitic laths have also become the centre of attention. This treatment is called the Q-P process (quenching and partitioning). In this experimental program the quenching temperature and the isothermal holding temperature for diffusion carbon distribution for three advanced high strength steels with carbon content of 0.43 % was examined. The alloying strategies have a different content of manganese and silicon, which leads to various martensite start and finish temperatures. The model treatment was carried out using a thermomechanical simulator. Tested regimes resulted in a tensile strength of over 2000MPa with a ductility of above 14 %. The increase of the partitioning temperature influenced the intensity of martensite tempering and caused the decrease of tensile strength by 400MPa down to 1600MPa and at the same time more than 10 % growth of ductility occurred, increasing it to more than 20%.

Sign in / Sign up

Export Citation Format

Share Document