scholarly journals Effect of Quenching and Partitioning Temperatures in the Q-P Process on the Properties of AHSS with Various Amounts of Manganese and Silicon

2012 ◽  
Vol 706-709 ◽  
pp. 2734-2739 ◽  
Author(s):  
Hana Jirková ◽  
Ludmila Kučerová ◽  
Bohuslav Mašek
Keyword(s):  
Tensile Strength ◽  
Retained Austenite ◽  
Isothermal Holding ◽  
Bainitic Ferrite ◽  
High Strength Steels ◽  
High Strength ◽  
Experimental Program ◽  
Quenching Temperature ◽  
Quenching And Partitioning ◽  
Advanced High Strength Steels

The use of the combined influence of retained austenite and bainitic ferrite to improve strength and ductility has been known for many years from the treatment of multiphase steels. Recently, the very fine films of retained austenite along the martensitic laths have also become the centre of attention. This treatment is called the Q-P process (quenching and partitioning). In this experimental program the quenching temperature and the isothermal holding temperature for diffusion carbon distribution for three advanced high strength steels with carbon content of 0.43 % was examined. The alloying strategies have a different content of manganese and silicon, which leads to various martensite start and finish temperatures. The model treatment was carried out using a thermomechanical simulator. Tested regimes resulted in a tensile strength of over 2000MPa with a ductility of above 14 %. The increase of the partitioning temperature influenced the intensity of martensite tempering and caused the decrease of tensile strength by 400MPa down to 1600MPa and at the same time more than 10 % growth of ductility occurred, increasing it to more than 20%.

scholarly journals Heat Treatment Design for a QP Steel: Effect of Partitioning Temperature

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1136
Author(s):  
Marcel Carpio ◽  
Jessica Calvo ◽  
Omar García ◽  
Juan Pablo Pedraza ◽  
José María Cabrera
Keyword(s):  
Retained Austenite ◽  
High Strength Steels ◽  
High Strength ◽  
Tensile Tests ◽  
Quenching Temperature ◽  
Advanced High Strength Steels ◽  
New Family ◽  
Automotive Parts ◽  
Fresh Martensite ◽  
Industry Needs

Designing a new family of advanced high-strength steels (AHSSs) to develop automotive parts that cover early industry needs is the aim of many investigations. One of the candidates in the 3rd family of AHSS are the quenching and partitioning (QP) steels. These steels display an excellent relationship between strength and formability, making them able to fulfill the requirements of safety, while reducing automobile weight to enhance the performance during service. The main attribute of QP steels is the TRIP effect that retained austenite possesses, which allows a significant energy absorption during deformation. The present study is focused on evaluating some process parameters, especially the partitioning temperature, in the microstructures and mechanical properties attained during a QP process. An experimental steel (0.2C-3.5Mn-1.5Si (wt%)) was selected and heated according to the theoretical optimum quenching temperature. For this purpose, heat treatments in a quenching dilatometry and further microstructural and mechanical characterization were carried out by SEM, XRD, EBSD, and hardness and tensile tests, respectively. The samples showed a significant increment in the retained austenite at an increasing partitioning temperature, but with strong penalization on the final ductility due to the large amount of fresh martensite obtained as well.

Quenching and Partitioning of Ni-Added High Strength Steels

2007 ◽  
Vol 539-543 ◽  
pp. 4476-4481 ◽  
Author(s):  
F.C. Rizzo ◽  
A.R. Martins ◽  
John G. Speer ◽  
David K. Matlock ◽  
A. Clarke ◽  
...  
Keyword(s):  
Retained Austenite ◽  
High Strength Steels ◽  
High Strength ◽  
Processing Parameters ◽  
Carbide Formation ◽  
X Ray Diffraction ◽  
Quenching And Partitioning ◽  
Steel Microstructure ◽  
Advanced High Strength Steels ◽  
Treatment Procedures

High strength steels containing significant fractions of retained austenite have been developed in recent years, and are the subject of growing commercial interest when associated with the TRIP phenomenon during deformation. A new process concept “quenching and partitioning” (Q&P) has been proposed by CSM/USA, and the results show the potential to create a new kind of steel microstructure with controlled amounts of retained austenite, enriched by carbon partitioning. Four steels containing C, Si, Mn, Ni, Cr and Mo, were designed with variation in the Ni and C content, aiming to decrease Bs temperature and to suppress carbide formation during the partitioning treatment. Several heat-treatment procedures were performed in specimens previously machined for tensile testing, while x-ray diffraction was used to determine the fraction of retained austenite. The tensile test results showed that except for the high C high Ni alloy, most of the processing conditions resulted in strengths superior to those of advanced high strength steels (AHSS), although it is importantly recognized that higher alloy additions were used in this study, in comparison with conventional AHSS grades.. A variety of strength and ductility combinations were observed, confirming the potential of the Q&P process and illustrating the strong influence of the final microstructure on the mechanical properties. Experimental results for samples partitioned at 400 °C indicate that higher ultimate tensile strength is associated with higher fraction of retained austenite for multiple heat treatments of each alloy investigated. The amount of retained austenite obtained was generally lower than that predicted by the model. Further studies are in progress to understand the influence of alloying and processing parameters (time/temperature) on the partitioning of carbon and precipitation of transition carbides.

scholarly journals Temperature Dependence of the Static and Dynamic Behaviour in a Quenching and Partitioning Processed Low-Si Steel

Metals ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 509 ◽  
Author(s):  
Florian Vercruysse ◽  
Carola Celada-Casero ◽  
Bernd M. Linke ◽  
Patricia Verleysen ◽  
Roumen H. Petrov
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
High Strength Steels ◽  
High Strength ◽  
Dynamic Strain ◽  
Strain Rates ◽  
Trip Effect ◽  
Quenching And Partitioning ◽  
Advanced High Strength Steels ◽  
Wide Range

Because of their excellent combination of strength and ductility, quenching and partitioning (Q & P) steels have a great chance of being added to the third generation of advanced high strength steels. The large ductility of Q & P steels arises from the presence of 10% to 15% of retained austenite which postpones necking due to the transformation induced plasticity (TRIP) effect. Moreover, Q & P steels show promising forming properties with favourable Lankford coefficients, while their planar anisotropy is low due to a weak texture. The stability of the metastable austenite is the key to obtain tailored properties for these steels. To become part of the newest generation of advanced high strength steels, Q & P steels have to preserve their mechanical properties at dynamic strain rates and over a wide range of temperatures. Therefore, in the present study, a low-Si Q & P steel was tested at temperatures from −40 °C to 80 °C and strain rates from 0.001 s−1 to 500 s−1. Results show that the mechanical properties are well-preserved at the lowest temperatures. Indeed, at −40 °C and room temperature, no significant loss of the deformation capacity is observed even at dynamic strain rates. This is attributed to the presence of a large fraction of austenite that is so (thermally) stable that it does not transform in the absence of deformation. In addition, the high stability of the austenite decreases the elongation at high test temperatures (80 °C). The additional adiabatic heating in the dynamic tests causes the largest reduction of the uniform strain for the samples tested at 80 °C. Quantification of the retained austenite fraction in the samples after testing confirmed that, at the highest temperature and strain rate, the TRIP effect is suppressed.

scholarly journals The Effect of Alloying on Mechanical Properties of Advanced High Strength Steels

2014 ◽  
Vol 59 (3) ◽  
pp. 1189-1192 ◽  
Author(s):  
L. Kučerová ◽  
H. Jirková ◽  
B. Mašek
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Cooling Rate ◽  
High Strength Steels ◽  
High Strength ◽  
Microstructure Development ◽  
Quenching And Partitioning ◽  
Advanced High Strength Steels ◽  
Quenching And Partitioning Process ◽  
Effect Of Alloying

Abstract Quenching and partitioning process with incorporated incremental deformation was optimized for six high strength steels with various contents of carbon (0.4-0.6%), manganese (0.6-1.2), silicon (2-2.6%) and chromium (0.8-1.3%). The optimization was gradually done for each steel with respect to the final microstructures and properties. The effect of cooling rate, quenching and partitioning temperature on microstructure development was further investigated. Interesting combinations of mechanical properties were obtained, with tensile strength in the region of 1600-2400 MPa and ductility of 6-20%.

scholarly journals The Effect of Mn and Si on the Properties of Advanced High Strength Steels Processed by Quenching and Partitioning

2010 ◽  
Vol 654-656 ◽  
pp. 94-97 ◽  
Author(s):  
Bohuslav Mašek ◽  
Hana Jirková ◽  
Daniela Hauserova ◽  
Ludmila Kučerová ◽  
Danuše Klauberová
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
Volume Fraction ◽  
High Strength Steels ◽  
High Strength ◽  
Microstructural Development ◽  
X Ray Diffraction ◽  
Quenching And Partitioning ◽  
Advanced High Strength Steels ◽  
High Ultimate Strength

The concepts new types of materials are, for economic reasons, focused mainly on low alloyed steels with a good combination of strength and ductility. Suitable heat and thermo-mechanical treatments play an important role for the utilization of these materials. Different alloying strategies are used to influence phase transformations. The quenching and partitioning process (Q-P Process) is one of the heat treatment methods which can result in a high ultimate strength as well as a good ductility. However, these good properties can be obtained only if a sufficient amount of retained austenite is stabilized. The influence of different contents of manganese, silicon and chromium on microstructural development and mechanical properties were experimentally tested. Alloying elements were used to stabilize the retained austenite in the final microstructure and also to strengthen the solid solution. Ultimate strengths of over 2000MPa with ductility over 10% were reached after the optimization of the Q-P Process. The microstructures were analyzed using several microscopic methods; mechanical properties were determined by a tensile test and the volume fraction of the retained austenite was established by X-ray diffraction phase analysis.

Austenite Stabilization by Quenching and Partitioning in a Low-Alloy Medium Carbon Steel

2012 ◽  
Vol 706-709 ◽  
pp. 2234-2239
Author(s):  
E. Paravicini Bagliani ◽  
E. Anelli ◽  
Marco Boniardi
Keyword(s):  
Retained Austenite ◽  
Room Temperature ◽  
Isothermal Holding ◽  
High Strength Steels ◽  
High Strength ◽  
Medium Carbon Steel ◽  
Medium Carbon ◽  
Quenching And Partitioning ◽  
Untransformed Austenite

Innovative treatments like quenching and partitioning (Q&P) have been recently proposed to improve the combination of strength and ductility of high strength steels by stabilization of significant fractions of retained austenite in a microstructure of tempered martensite. The decomposition of austenite into bainite and carbides precipitation are the two main competitive processes that reduce the content of retained austenite achievable at room temperature. A medium carbon low-silicon steel (0.46% C and 0.25% Si) has been studied to identify in which limits the austenite can be enriched in C and stabilized by Q&P, although a silicon content well below 1.5%, commonly used to retard cementite precipitation, is adopted; indeed, high Si contents are detrimental to the surface quality of the product due to the formation of adherent scale in high temperature manufacturing cycles. The heat treatments have been carried out with a quenching dilatometer, investigating the carbon partitioning process mainly below Ms, where cementite precipitation is not activated. The dilatometric curves show the progressive enrichment of carbon in the untransformed austenite and the occurrence of austenite phase transformation during the isothermal holding below Ms. A range of temperatures and times has been found where a content of about 10% of retained austenite can be stabilized at room temperature, a percentage much lower than the theoretical maximum achievable with the carbon content of this steel.

scholarly journals Influence of the Quenching and Partitioning Process on the Transformation Kinetics and Hardness in a Lean Medium Manganese TRIP Steel

Metals ◽  
2019 ◽  
Vol 9 (3) ◽  
pp. 353 ◽  
Author(s):  
Simone Kaar ◽  
Reinhold Schneider ◽  
Daniel Krizan ◽  
Coline Béal ◽  
Christof Sommitsch
Keyword(s):  
Isothermal Holding ◽  
Bainitic Ferrite ◽  
High Strength ◽  
Quenching Temperature ◽  
Quenching And Partitioning ◽  
Novel Approach ◽  
Medium Mn Steel ◽  
C Partitioning ◽  
Mn Steel ◽  
Isothermal Bainitic Transformation

The quenching and partitioning (Q&P) process of lean medium Mn steels is a novel approach for producing ultra-high strength and good formable steels. First, the steel is fully austenitized, followed by quenching to a specific quenching temperature (TQ) in order to adjust an appropriate amount of initial martensite (α’initial). Subsequently, the steel is reheated to a partitioning temperature (TP) in order to ensure C-partitioning from α’initial to remaining austenite (γremain) and thus retained austenite (RA) stabilization. After isothermal holding, the steel is quenched to room temperature (RT), in order to achieve a martensitic-austenitic microstructure, where the meta-stable RA undergoes the strain-induced martensitic transformation by the so-called transformation induced plasticity (TRIP) effect. This paper systematically investigates the influence of the Q&P process on the isothermal bainitic transformation (IBT) kinetics in a 0.2C-4.5Mn-1.3Al lean medium Mn steel by means of dilatometry. Therefore, the Q&P annealing approach was precisely compared to the TRIP-aided bainitic ferrite (TBF) process, where the samples were directly quenched to the temperature of the IBT after full austenitization. The results indicated an accelerated IBT for the Q&P samples, caused by the formation of α’initial during quenching below the martensite start (MS) temperature. Furthermore, a significant influence of the annealing parameters, such as TQ and TP, was observed with regard to the transformation behavior. For further characterization, light optical microscopy (LOM) and scanning electron microscopy (SEM) were applied, showing a microstructure consisting of a martensitic-bainitic matrix with finely distributed RA islands. Saturation magnetization method (SMM) was used to determine the amount of RA, which was primarily depending on TQ. Furthermore, the hardness according to Vickers revealed a remarkable impact of the annealing parameters, such as TQ and TP, on the predicted mechanical properties.

scholarly journals Carbon Redistribution and Microstructural Evolution Study during Two-Stage Quenching and Partitioning Process of High-Strength Steels by Modeling

Materials ◽  
2018 ◽  
Vol 11 (11) ◽  
pp. 2302 ◽  
Author(s):  
Yilin Wang ◽  
Huicheng Geng ◽  
Bin Zhu ◽  
Zijian Wang ◽  
Yisheng Zhang
Keyword(s):  
Retained Austenite ◽  
Volume Fraction ◽  
High Strength Steels ◽  
High Strength ◽  
Simulation Method ◽  
Low Carbon ◽  
Two Stage ◽  
Quenching And Partitioning ◽  
Carbon Redistribution ◽  
Carbon Martensite

The application of the quenching and partitioning (Q-P) process on advanced high-strength steels improves part ductility significantly with little decrease in strength. Moreover, the mechanical properties of high-strength steels can be further enhanced by the stepping-quenching-partitioning (S-Q-P) process. In this study, a two-stage quenching and partitioning (two-stage Q-P) process originating from the S-Q-P process of an advanced high-strength steel 30CrMnSi2Nb was analyzed by the simulation method, which consisted of two quenching processes and two partitioning processes. The carbon redistribution, interface migration, and phase transition during the two-stage Q-P process were investigated with different temperatures and partitioning times. The final microstructure of the material formed after the two-stage Q-P process was studied, as well as the volume fraction of the retained austenite. The simulation results indicate that a special microstructure can be obtained by appropriate parameters of the two-stage Q-P process. A mixed microstructure, characterized by alternating distribution of low carbon martensite laths, small-sized low-carbon martensite plates, retained austenite and high-carbon martensite plates, can be obtained. In addition, a peak value of the volume fraction of the stable retained austenite after the final quenching is obtained with proper partitioning time.

Application of Quenching-Partitioning-Tempering Process in Hot Rolled Plate Fabrication

2010 ◽  
Vol 654-656 ◽  
pp. 82-85 ◽  
Author(s):  
Shu Zhou ◽  
Ying Wang ◽  
Nai Lu Chen ◽  
Yong Hua Rong ◽  
Jian Feng Gu
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
High Strength Steels ◽  
High Strength ◽  
Significant Fraction ◽  
Rolled Plate ◽  
Quenching And Partitioning ◽  
Good Ductility ◽  
Hot Rolled ◽  
Rolled Plates

The quenching-partitioning-tempering (Q-P-T) process, based on the quenching and partitioning (Q&P) treatment, has been proposed for producing high strength steels containing significant fraction of film-like retained austenite and controlled amount of fine martensite laths. In this study, a set of Q-P-T processes for C-Mn-Si-Ni-Nb hot rolled plates are designed and realized. The steels with Q-P-T processes present a combination of high strength and relatively good ductility. The origin of such mechanical properties is revealed by microstructure characterization.

Sign in / Sign up

Export Citation Format

Share Document