Change in polymer supermolecular structure on heat-treatment of technical purpose polyester yarns

Aluminum-copper-silicon thin films have been considered as an interconnection metallurgy for integrated circuit applications. Various schemes have been proposed to incorporate small percent-ages of silicon into films that typically contain two to five percent copper. We undertook a study of the total effect of silicon on the aluminum copper film as revealed by transmission electron microscopy, scanning electron microscopy, x-ray diffraction and ion microprobe techniques as a function of the various deposition methods.X-ray investigations noted a change in solid solution concentration as a function of Si content before and after heat-treatment. The amount of solid solution in the Al increased with heat-treatment for films with ≥2% silicon and decreased for films <2% silicon.

Download Full-text

The influence of heat treatment on the fiber/matrix interface in a SiC-reinforced glassceramic

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100105771 ◽

1988 ◽

Vol 46 ◽

pp. 742-743

Author(s):

E. Bischoff ◽

O. Sbaizero

Keyword(s):

Heat Treatment ◽

Aluminum Silicate ◽

Lithium Aluminum ◽

Interfacial Region ◽

Specimen Preparation ◽

Crack Wake ◽

Pull Out ◽

Annealed Material ◽

Ultrasonic Drilling ◽

Fiber Matrix Interface

Fiber or whisker reinforced ceramics show improved toughness and strength. Bridging by intact fibers in the crack wake and fiber pull-out after failure contribute to the additional toughness. These processes are strongly influenced by the sliding and debonding resistance of the interfacial region. The present study examines the interface in a laminated 0/90 composite consisting of SiC (Nicalon) fibers in a lithium-aluminum-silicate (LAS) glass-ceramic matrix. The material shows systematic changes in sliding resistance upon heat treatment.As-processed samples were annealed in air at 800 °C for 2, 4, 8, 16 and 100 h, and for comparison, in helium at 800 °C for 4 h. TEM specimen preparation of as processed and annealed material was performed with special care by cutting along directions having the fibers normal and parallel to the section plane, ultrasonic drilling, dimpling to 100 pm and final ionthinning. The specimen were lightly coated with Carbon and examined in an analytical TEM operated at 200 kV.

Download Full-text

Strain-induced martensite effects on transgranular carbide precipitation in type 304 stainless steels

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100087331 ◽

1991 ◽

Vol 49 ◽

pp. 604-605

Author(s):

A.H. Advani ◽

L.E. Murr ◽

D. Matlock

Keyword(s):

Heat Treatment ◽

Grain Boundary ◽

Stress Corrosion Cracking ◽

Stainless Steels ◽

Deformation Twin ◽

Austenitic Stainless Steels ◽

Carbide Precipitation ◽

Strain Induced Martensite ◽

Type 304

Thermomechanically induced strain is a key variable producing accelerated carbide precipitation, sensitization and stress corrosion cracking in austenitic stainless steels (SS). Recent work has indicated that higher levels of strain (above 20%) also produce transgranular (TG) carbide precipitation and corrosion simultaneous with the grain boundary phenomenon in 316 SS. Transgranular precipitates were noted to form primarily on deformation twin-fault planes and their intersections in 316 SS.Briant has indicated that TG precipitation in 316 SS is significantly different from 304 SS due to the formation of strain-induced martensite on 304 SS, though an understanding of the role of martensite on the process has not been developed. This study is concerned with evaluating the effects of strain and strain-induced martensite on TG carbide precipitation in 304 SS. The study was performed on samples of a 0.051%C-304 SS deformed to 33% followed by heat treatment at 670°C for 1 h.

Download Full-text