Effects of silicone surfactant on the cell size and thermal conductivity of rigid polyurethane foams by environmentally friendly blowing agents

2009 ◽  
Vol 17 (1) ◽  
pp. 44-50 ◽  
Author(s):  
Mi Sun Han ◽  
Seok Jin Choi ◽  
Ji Mun Kim ◽  
Youn Hee Kim ◽  
Woo Nyon Kim ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Cell Size ◽  
Environmentally Friendly ◽  
Polyurethane Foams ◽  
Silicone Surfactant ◽  
Rigid Polyurethane Foams ◽  
Blowing Agents

Improvement of thermal conductivity of rigid polyurethane foams with aluminum nitride filler

2021 ◽  
pp. 026248932198897
Author(s):  
Serife Akkoyun ◽  
Meral Akkoyun
Keyword(s):  
Thermal Conductivity ◽  
Aluminum Nitride ◽  
Polyurethane Foams ◽  
Thermal Transitions ◽  
Rigid Polyurethane Foams ◽  
Noticeable Increase ◽  
Polyurethane Composite ◽  
Composite Foams ◽  
Step Procedure ◽  
Electrical Conductivities

The aim of this work is the fabrication of electrically insulating composite rigid polyurethane foams with improved thermal conductivity. Therefore, this study is focused on the effect of aluminum nitride (AlN) on the thermal and electrical conductivities of rigid polyurethane foams. For this purpose, aluminum nitride/rigid polyurethane composite foams were prepared using a three-step procedure. The electrical and thermal conductivities of the foams were characterized. The thermal transitions, mechanical properties and morphology of the foams were also examined. The results reveal that AlN induces an increase of the thermal conductivity of rigid polyurethane foam of 24% which seems to be a relatively noticeable increase in polymeric foams. The low electrical conductivity of the foams is preserved.

Bio-based Polyurethane-clay Nanocomposite Foams: Systheses and Properties

2009 ◽  
Vol 1188 ◽  
Author(s):  
Min Liu ◽  
Zoran S. Petrovic ◽  
Yijin Xu
Keyword(s):  
Thermal Conductivity ◽  
Thermal Insulation ◽  
Cell Structure ◽  
Polyurethane Foams ◽  
Mechanical And Thermal Properties ◽  
Cell Content ◽  
Modified Clay ◽  
Rigid Polyurethane Foams ◽  
Nanocomposite Foams ◽  
Organically Modified

AbstractStarting from a bio-based polyol through modification of soybean oil, BIOH™ X-210, two series of bio-based polyurethanes-clay nanocomposite foams have been prepared. The effects of organically-modified clay types and loadings on foam morphology, cell structure, and the mechanical and thermal properties of these bio-based polyurethanes-clay nanocomposite foams have been studied with optical microscopy, compression test, thermal conductivity, DMA and TGA characterization. Density of nanocomposite foams decreases with the increase of clay loadings, while reduced 10% compressive stress and yield stress keep constant up to 2.5% clay loading in polyol. The friability of rigid polyurethane-clay nanocomposite foams is high than that of foam without clay, and the friability for nanofoams from Cloisite® 10A is higher than that from 30B at the same clay loadings. The incorporation of clay nanoplatelets decreases the cell size in nanocomposite foams, meanwhile increases the cell density; which would be helpful in terms of improving thermal insulation properties. All the nanocomposite foams were characterized by increased closed cell content compared with the control foam from X-210 without clay, suggesting the potential to improve thermal insulation of rigid polyurethane foams by utilizing organically modified clay. Incorporation of clay into rigid polyurethane foams results in the increase in glass transition temperature: the Tg increased from 186 to 197 to 204 °C when 30B concentration in X-210 increased from 0 to 0.5 to 2.5%, respectively. Even though the thermal conductivity of nanocomposite foams from 30B is lower than or equal to that of rigid polyurethane control foam from X-210, thermal conductivity of nanocomposite foams from 10A is higher than that of control at all 10A concentrations. The reason for this abnormal phenomenon is not clear at this moment; investigation on this is on progress.

Cryogenic thermal insulating and mechanical properties of rigid polyurethane foams blown with hydrofluoroolefin: Effect of perfluoroalkane

2021 ◽  
pp. 0021955X2110626
Author(s):  
Tae Seok Kim ◽  
Yeongbeom Lee ◽  
Chul Hyun Hwang ◽  
Kwang Ho Song ◽  
Woo Nyon Kim
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Thermal Stability ◽  
Cell Size ◽  
Thermal Insulation ◽  
Coefficient Of Thermal Expansion ◽  
Lower Surface ◽  
Polyurethane Foams ◽  
Insulation Material ◽  
Pu Foams

The effect of perfluoroalkane (PFA) on the morphology, thermal conductivity, mechanical properties and thermal stability of rigid polyurethane (PU) foams was investigated under ambient and cryogenic conditions. The PU foams were blown with hydrofluorolefin. Morphological results showed that the minimum cell size (153 μm) was observed when the PFA content was 1.0 part per hundred polyols by weight (php). This was due to the lower surface tension of the mixed polyol solution when the PFA content was 1.0 php. The thermal conductivity of PU foams measured under ambient (0.0215 W/mK) and cryogenic (0.0179 W/mK at −100°C) conditions reached a minimum when the PFA content was 1.0 php. The low value of thermal conductivity was a result of the small cell size of the foams. The above results suggest that PFA acted as a nucleating agent to enhanced the thermal insulation properties of PU foams. The compressive and shear strengths of the PU foams did not appreciably change with PFA content at either −170°C or 20°C. However, it shows that the mechanical strengths at −170°C and 20°C for the PU foams meet the specification. Coefficient of thermal expansion, and thermal shock tests of the PU foams showed enough thermal stability for the LNG carrier’s operation temperature. Therefore, it is suggested that the PU foams blown by HFO with the PFA addition can be used as a thermal insulation material for a conventional LNG carrier.

scholarly journals Rigid Polyurethane Foams Modified with Biochar

Materials ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 5616
Author(s):  
Katarzyna Uram ◽  
Maria Kurańska ◽  
Jacek Andrzejewski ◽  
Aleksander Prociak
Keyword(s):  
Thermal Conductivity ◽  
Thermal Stability ◽  
Thermal Insulation ◽  
Foam Cells ◽  
Polyurethane Foams ◽  
Cross Sectional ◽  
Rigid Polyurethane Foams ◽  
Insulation Materials

This paper presents results of research on the preparation of biochar-modified rigid polyurethane foams that could be successfully used as thermal insulation materials. The biochar was introduced into polyurethane systems in an amount of up to 20 wt.%. As a result, foam cells became elongated in the direction of foam growth and their cross-sectional areas decreased. The filler-containing systems exhibited a reduction in their apparent densities of up to 20% compared to the unfilled system while maintaining a thermal conductivity of 25 mW/m·K. Biochar in rigid polyurethane foams improved their dimensional and thermal stability.

Rigid polyurethane foams moulded with new generation blowing agents

Polimery ◽  
2003 ◽  
Vol 48 (07/08) ◽  
pp. 565-567
Author(s):  
ALEKSANDER PROCIAK ◽  
MARCIN FIGURA
Keyword(s):  
Polyurethane Foams ◽  
Rigid Polyurethane Foams ◽  
Blowing Agents ◽  
New Generation

The influence of blowing agents type on foaming process and properties of rigid polyurethane foams

Polimery ◽  
2018 ◽  
Vol 63 (10) ◽  
pp. 672-678 ◽  
Author(s):  
Maria Kuranska ◽  
Aleksander Prociak ◽  
Slawomir Michalowski ◽  
Karolina Zawadzinska
Keyword(s):  
Polyurethane Foams ◽  
Rigid Polyurethane Foams ◽  
Blowing Agents ◽  
Foaming Process

scholarly journals Properties of Rigid Polyurethane Foams with Blowing Agents and Catalysts

2004 ◽  
Vol 36 (5) ◽  
pp. 368-373 ◽  
Author(s):  
Kun Hyung Choe ◽  
Dong Soo Lee ◽  
Won Jin Seo ◽  
Woo Nyon Kim
Keyword(s):  
Polyurethane Foams ◽  
Rigid Polyurethane Foams ◽  
Blowing Agents

The Synthesis and Application of a Novel Class of Polyols for Preparation of Polyurethane

2013 ◽  
Vol 357-360 ◽  
pp. 1441-1445
Author(s):  
Xiao Lin Li ◽  
Zheng Fang ◽  
Dong Ji ◽  
Zhi Dong Wan ◽  
Kai Guo
Keyword(s):  
Thermal Conductivity ◽  
Compressive Strength ◽  
Polyurethane Foams ◽  
Low Density ◽  
Cell Content ◽  
Low Thermal Conductivity ◽  
High Compressive Strength ◽  
Rigid Polyurethane Foams ◽  
Closed Cell ◽  
Rigid Foams

The synthesis of a novel class of diamine-based polyols derivatives and the potentials and the limitations of these polyols were reported. This class of diamine-based polyols with high hydroxyl values and no acid values can be used in rigid polyurethane foams. The prepared rigid foams show the properties of low density, high closed cell content, low thermal conductivity, and high compressive strength.

Sign in / Sign up

Export Citation Format

Share Document