Bio-based Polyurethane-clay Nanocomposite Foams: Systheses and Properties

2009 ◽  
Vol 1188 ◽  
Author(s):  
Min Liu ◽  
Zoran S. Petrovic ◽  
Yijin Xu
Keyword(s):  
Thermal Conductivity ◽  
Thermal Insulation ◽  
Cell Structure ◽  
Polyurethane Foams ◽  
Mechanical And Thermal Properties ◽  
Cell Content ◽  
Modified Clay ◽  
Rigid Polyurethane Foams ◽  
Nanocomposite Foams ◽  
Organically Modified

AbstractStarting from a bio-based polyol through modification of soybean oil, BIOH™ X-210, two series of bio-based polyurethanes-clay nanocomposite foams have been prepared. The effects of organically-modified clay types and loadings on foam morphology, cell structure, and the mechanical and thermal properties of these bio-based polyurethanes-clay nanocomposite foams have been studied with optical microscopy, compression test, thermal conductivity, DMA and TGA characterization. Density of nanocomposite foams decreases with the increase of clay loadings, while reduced 10% compressive stress and yield stress keep constant up to 2.5% clay loading in polyol. The friability of rigid polyurethane-clay nanocomposite foams is high than that of foam without clay, and the friability for nanofoams from Cloisite® 10A is higher than that from 30B at the same clay loadings. The incorporation of clay nanoplatelets decreases the cell size in nanocomposite foams, meanwhile increases the cell density; which would be helpful in terms of improving thermal insulation properties. All the nanocomposite foams were characterized by increased closed cell content compared with the control foam from X-210 without clay, suggesting the potential to improve thermal insulation of rigid polyurethane foams by utilizing organically modified clay. Incorporation of clay into rigid polyurethane foams results in the increase in glass transition temperature: the Tg increased from 186 to 197 to 204 °C when 30B concentration in X-210 increased from 0 to 0.5 to 2.5%, respectively. Even though the thermal conductivity of nanocomposite foams from 30B is lower than or equal to that of rigid polyurethane control foam from X-210, thermal conductivity of nanocomposite foams from 10A is higher than that of control at all 10A concentrations. The reason for this abnormal phenomenon is not clear at this moment; investigation on this is on progress.

scholarly journals Rigid Polyurethane Foams Modified with Biochar

Materials ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 5616
Author(s):  
Katarzyna Uram ◽  
Maria Kurańska ◽  
Jacek Andrzejewski ◽  
Aleksander Prociak
Keyword(s):  
Thermal Conductivity ◽  
Thermal Stability ◽  
Thermal Insulation ◽  
Foam Cells ◽  
Polyurethane Foams ◽  
Cross Sectional ◽  
Rigid Polyurethane Foams ◽  
Insulation Materials

This paper presents results of research on the preparation of biochar-modified rigid polyurethane foams that could be successfully used as thermal insulation materials. The biochar was introduced into polyurethane systems in an amount of up to 20 wt.%. As a result, foam cells became elongated in the direction of foam growth and their cross-sectional areas decreased. The filler-containing systems exhibited a reduction in their apparent densities of up to 20% compared to the unfilled system while maintaining a thermal conductivity of 25 mW/m·K. Biochar in rigid polyurethane foams improved their dimensional and thermal stability.

The Synthesis and Application of a Novel Class of Polyols for Preparation of Polyurethane

2013 ◽  
Vol 357-360 ◽  
pp. 1441-1445
Author(s):  
Xiao Lin Li ◽  
Zheng Fang ◽  
Dong Ji ◽  
Zhi Dong Wan ◽  
Kai Guo
Keyword(s):  
Thermal Conductivity ◽  
Compressive Strength ◽  
Polyurethane Foams ◽  
Low Density ◽  
Cell Content ◽  
Low Thermal Conductivity ◽  
High Compressive Strength ◽  
Rigid Polyurethane Foams ◽  
Closed Cell ◽  
Rigid Foams

The synthesis of a novel class of diamine-based polyols derivatives and the potentials and the limitations of these polyols were reported. This class of diamine-based polyols with high hydroxyl values and no acid values can be used in rigid polyurethane foams. The prepared rigid foams show the properties of low density, high closed cell content, low thermal conductivity, and high compressive strength.

Study on the Methods for Measuring Closed Cell Content of Cellular Glass and its Thermal Insulation Performance

2016 ◽  
Vol 680 ◽  
pp. 68-71
Author(s):  
Chao Peng ◽  
Gui Qiang Li ◽  
Cheng Xin Sui ◽  
Hui Meng Zhang ◽  
Yu Hui Zhang
Keyword(s):  
Thermal Conductivity ◽  
Thermal Insulation ◽  
Cell Structure ◽  
Insulation Property ◽  
Cell Content ◽  
Measuring Condition ◽  
Effect Of Pressure ◽  
Cellular Glass ◽  
Closed Cell ◽  
Insulation Performance

The principle of measuring cellular glass by automatic densimeter was studied. The effect of pressure on closed cell content was researched in order to optimize the measuring pressure. The influence of closed cell content on the insulation property was analyzed by measuring thermal conductivity. The results showed that cell structure of cellular glass can distort or even be damaged with the increasing of pressure and the first condition for obtaining accurate closed cell content was to optimize the measuring condition and determine appropriate pressure. Closed cell content affects the insulation property of the cellular glass significantly.

Preparation and Characterization of Soybean Oil-based Flame Retardant Rigid Polyurethane Foams Containing Phosphaphenanthrene Groups

2020 ◽  
Vol 17 (10) ◽  
pp. 760-771
Author(s):  
Qirui Gong ◽  
Niangui Wang ◽  
Kaibo Zhang ◽  
Shizhao Huang ◽  
Yuhan Wang
Keyword(s):  
Soybean Oil ◽  
Flame Retardant ◽  
Chemical Structure ◽  
Cell Structure ◽  
Polyurethane Foams ◽  
Limiting Oxygen Index ◽  
Rigid Polyurethane Foams ◽  
Degradation Activation Energy ◽  
Ft Ir

A phosphaphenanthrene groups containing soybean oil based polyol (DSBP) was synthesized by epoxidized soybean oil (ESO) and 9,10-dihydro-oxa-10-phosphaphenanthrene-10-oxide (DOPO). Soybean oil based polyol (HSBP) was synthesized by ESO and H2O. The chemical structure of DSBP and HSBP were characterized with FT-IR and 1H NMR. The corresponding rigid polyurethane foams (RPUFs) were prepared by mixing DSBP with HSBP. The results revealed apparent density and compression strength of RPUFs decreased with increasing the DSBP content. The cell structure of RPUFs was examined by scanning electron microscope (SEM) which displayed the cells as spherical or polyhedral. The thermal degradation and flame retardancy of RPUFs were investigated by thermogravimetric analysis, limiting oxygen index (LOI), and UL 94 vertical burning test. The degradation activation energy (Ea) of first degradation stage reduced from 80.05 kJ/mol to 37.84 kJ/mol with 80 wt% DSBP. The RUPF with 80 wt% DSBP achieved UL94 V-0 rating and LOI 28.3. The results showed that the flame retardant effect was mainly in both gas phase and condensed phase.

Improvement of thermal conductivity of rigid polyurethane foams with aluminum nitride filler

2021 ◽  
pp. 026248932198897
Author(s):  
Serife Akkoyun ◽  
Meral Akkoyun
Keyword(s):  
Thermal Conductivity ◽  
Aluminum Nitride ◽  
Polyurethane Foams ◽  
Thermal Transitions ◽  
Rigid Polyurethane Foams ◽  
Noticeable Increase ◽  
Polyurethane Composite ◽  
Composite Foams ◽  
Step Procedure ◽  
Electrical Conductivities

The aim of this work is the fabrication of electrically insulating composite rigid polyurethane foams with improved thermal conductivity. Therefore, this study is focused on the effect of aluminum nitride (AlN) on the thermal and electrical conductivities of rigid polyurethane foams. For this purpose, aluminum nitride/rigid polyurethane composite foams were prepared using a three-step procedure. The electrical and thermal conductivities of the foams were characterized. The thermal transitions, mechanical properties and morphology of the foams were also examined. The results reveal that AlN induces an increase of the thermal conductivity of rigid polyurethane foam of 24% which seems to be a relatively noticeable increase in polymeric foams. The low electrical conductivity of the foams is preserved.

Cryogenic thermal insulating and mechanical properties of rigid polyurethane foams blown with hydrofluoroolefin: Effect of perfluoroalkane

2021 ◽  
pp. 0021955X2110626
Author(s):  
Tae Seok Kim ◽  
Yeongbeom Lee ◽  
Chul Hyun Hwang ◽  
Kwang Ho Song ◽  
Woo Nyon Kim
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Thermal Stability ◽  
Cell Size ◽  
Thermal Insulation ◽  
Coefficient Of Thermal Expansion ◽  
Lower Surface ◽  
Polyurethane Foams ◽  
Insulation Material ◽  
Pu Foams

The effect of perfluoroalkane (PFA) on the morphology, thermal conductivity, mechanical properties and thermal stability of rigid polyurethane (PU) foams was investigated under ambient and cryogenic conditions. The PU foams were blown with hydrofluorolefin. Morphological results showed that the minimum cell size (153 μm) was observed when the PFA content was 1.0 part per hundred polyols by weight (php). This was due to the lower surface tension of the mixed polyol solution when the PFA content was 1.0 php. The thermal conductivity of PU foams measured under ambient (0.0215 W/mK) and cryogenic (0.0179 W/mK at −100°C) conditions reached a minimum when the PFA content was 1.0 php. The low value of thermal conductivity was a result of the small cell size of the foams. The above results suggest that PFA acted as a nucleating agent to enhanced the thermal insulation properties of PU foams. The compressive and shear strengths of the PU foams did not appreciably change with PFA content at either −170°C or 20°C. However, it shows that the mechanical strengths at −170°C and 20°C for the PU foams meet the specification. Coefficient of thermal expansion, and thermal shock tests of the PU foams showed enough thermal stability for the LNG carrier’s operation temperature. Therefore, it is suggested that the PU foams blown by HFO with the PFA addition can be used as a thermal insulation material for a conventional LNG carrier.

scholarly journals Composites of Rigid Polyurethane Foams Reinforced with POSS

Polymers ◽  
2019 ◽  
Vol 11 (2) ◽  
pp. 336 ◽  
Author(s):  
Sylwia Członka ◽  
Anna Strąkowska ◽  
Krzysztof Strzelec ◽  
Agnieszka Adamus-Włodarczyk ◽  
Agnė Kairytė ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Properties ◽  
Water Absorption ◽  
Viscoelastic Behavior ◽  
Physical And Mechanical Properties ◽  
Polyurethane Foams ◽  
Bending Test ◽  
Mechanical And Thermal Properties ◽  
Rigid Polyurethane Foams ◽  
Cell Shapes

Rigid polyurethane foams (RPUFs) were successfully modified with different weight ratios (0.5 wt%, 1.5 wt% and 5 wt%) of APIB-POSS and AEAPIB-POSS. The resulting foams were evaluated by their processing parameters, morphology (Scanning Electron Microscopy analysis, SEM), mechanical properties (compressive test, three-point bending test and impact strength), viscoelastic behavior (Dynamic Mechanical Analysis, DMA), thermal properties (Thermogravimetric Analysis, TGA, and thermal conductivity) and application properties (contact angle, water absorption and dimensional analysis). The results showed that the morphology of modified foams is significantly affected by the type of the filler and filler content, which resulted in inhomogeneous, irregular, large cell shapes and further affected the physical and mechanical properties of resulting materials. RPUFs modified with APIB-POSS represent better mechanical and thermal properties compared to the RPUFs modified with AEAPIB-POSS. The results showed that the best results were obtained for RPUFs modified with 0.5 wt% of APIB-POSS. For example, in comparison with unfilled foam, compositions modified with 0.5 wt% of APIB-POSS provide greater compression strength, better flexural strength and lower water absorption.

Effect of Nanoclay on the Physical-Mechanical and Thermal Properties and Microstructure of Extruded Noncross-Linked LDPE Nanocomposite Foams

2011 ◽  
Vol 471-472 ◽  
pp. 751-756 ◽  
Author(s):  
F. Zandi ◽  
M. Rezaei ◽  
A. Kasiri
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Cell Size ◽  
Flame Retardancy ◽  
Image Analyzer ◽  
Mechanical And Thermal Properties ◽  
Average Cell Size ◽  
Cell Size Distribution ◽  
Average Cell ◽  
Nanocomposite Foams

Novel noncross-linked low density polyethylene (LDPE) foams were produced by extrusion process. In this study the effects of Organophilic Montmorillonite (OMMT) nanoclay (DK1) on thermal conductivity, flame retardancy, morphological and mechanical properties of LDPE foams have been investigated. Nanoclay dispersion in LDPE foam structure was examined by X-ray diffraction (XRD), microstructure was observed by an optical microscope and analyzed by Bel View image analyzer, thermal conductivity was studied by a simple transient method, mechanical properties was investigated using a tensile-compression Zwick-Roell machine as well as the flame retardancy of the samples was examined by flammability test. The optimum nanoclay content was determined by comparison of the properties in nanocomposite and neat LDPE foams. Due to the presence of nanoclay in the foam and decreasing the cell nucleation energy around the nanoclay, the average cell size was decreased as well as the cell density and microstructure uniformity was increased. In XRD patterns of LDPE nanocomposite foams, OMMT (DK1) characteristic peak was not observed as evidence of nanoclay intercalation-exfoliation in the polymer matrix, which led to the production of foams with homogenous microstructure. Furthermore, this nanocomposites showed lower thermal conductivity compared to neat LDPE foam, which can be attributed to the cell size reduction as well as narrow cell size distribution in nanocomposite foams. Compression test results demonstrated that LDPE nanocomposite foams with proper clay contents have improved mechanical properties (Young’s modulus, compressive strength). Furthermore due to the presence of DK1 nanoclay, LDPE foam showed a good char formation as an evidence of their flame retardancy.

Sign in / Sign up

Export Citation Format

Share Document