The influence of bending mode ultrasonic-assisted friction stir welding of Al-6061-T6 alloy on residual stress, welding force and macrostructure

2017 ◽  
Vol 95 (5-8) ◽  
pp. 2757-2766 ◽  
Author(s):  
I. Alinaghian ◽  
M. Honarpisheh ◽  
S. Amini
Keyword(s):  
Residual Stress ◽  
Friction Stir Welding ◽  
Friction Stir ◽  
Al 6061 ◽  
Bending Mode ◽  
Ultrasonic Assisted ◽  
Welding Force

Numerical Simulation of Plunge Force During the Plunge Phase of Friction Stir Welding and Ultrasonic Assisted FSW

2008 ◽  
Author(s):  
Kwanghyun Park ◽  
Bongsuk Kim ◽  
Jun Ni
Keyword(s):  
Numerical Simulation ◽  
Friction Stir Welding ◽  
High Frequency ◽  
Hybrid Welding ◽  
Ultrasonic Vibrations ◽  
Welding Quality ◽  
Friction Stir ◽  
Ultrasonic Assisted ◽  
Welding Force ◽  
Welding Technique

Ultrasonic assisted friction stir welding (UaFSW) is an hybrid welding technique, where high frequency vibration is superimposed on the movement of a rotating tool. The benefit of using ultrasonic vibration in the FSW process refers to the reduction in the welding force and to the better welding quality. The UaFSW system is being developed and its mechanism needs to be understood using both the experiments and the numerical simulations. In this paper, FE simulations of FSW and UaFSW using ABAQUS/Explicit were carried out to examine plunge forces during the plunge phase of FSW and UaFSW, respectively. First, the simulations of the conventional FSW process were validated. Then, simulation of UaFSW process was performed by imposing sinusoidal horizontal ultrasonic vibrations on the tool.

Experimental Study on Friction Stir Welding of Dissimilar Al 6061 to Trip 780/800 Steel

2014 ◽  
Author(s):  
Xun Liu ◽  
Shuhuai Lan ◽  
Jun Ni
Keyword(s):  
Friction Stir Welding ◽  
Cross Sections ◽  
Welding Speed ◽  
Rotational Speed ◽  
Maximum Temperature ◽  
Friction Stir ◽  
Al 6061 ◽  
Tool Axis ◽  
Edge Temperature ◽  
Welding Force

Friction stir welding (FSW) of dissimilar Al 6061 and TRIP 780/800 steel has been performed under different process parameters, including tool rotational speed, welding speed as well as the relative position of the tool axis to the abutting edge. Temperature and mechanical welding force was recorded during the process. Welding speed has an insignificant effect on either the maximum temperature or welding force. However, it can directly change the length of high temperature duration, which will accordingly influence temperature distribution in the weld and the microstructure. Higher rotational speed can effectively elevate weld temperature through greater amount of heat input. Metallurgical observations on weld cross sections perpendicular to the joint line was performed using both optical and scanning electron microscope. Microstructure evolution was analyzed and related to the force and temperature measurement results during the FSW process.

Residual stress, tensile strength, and macrostructure investigations on ultrasonic assisted friction stir welding of AA 6061-T6

2018 ◽  
Vol 53 (7) ◽  
pp. 494-503 ◽  
Author(s):  
Iman Alinaghian ◽  
Saeid Amini ◽  
Mohammad Honarpisheh
Keyword(s):  
Residual Stress ◽  
Tensile Strength ◽  
Friction Stir Welding ◽  
Weld Zone ◽  
Ultrasonic Power ◽  
Ultrasonic Vibrations ◽  
Friction Stir ◽  
Longitudinal Residual Stress ◽  
Ultrasonic Assisted

In recent decades, ultrasonic vibrations are used in manufacturing processes because they can improve tool life, material performance, and quality. One of them which can be integrated with ultrasonic vibrations is friction stir welding called ultrasonic assisted friction stir welding. In previous studies, the effect of ultrasonic vibrations on the mechanical, metallurgical, and thermal properties was investigated and there is not any residual stress investigations on ultrasonic assisted friction stir welding. Since residual stress plays an important role in performance and stability of components, the influence of ultrasonic power on the longitudinal residual stress in friction stir welding is investigated in this work. In spite of residual stress, tensile strength and quality of weldment were investigated as complementary terms to ensure successful performance of ultrasonic assisted friction stir welding. The findings indicated that high-frequency vibrations with power of 200 W can reduce the maximum tensile residual stress about 45% and significantly increase tensile strength. Also, ultrasonic vibrations prevent defect such has voids and tunnel in weld zone due to peening effect in ultrasonic assisted friction stir welding.

Experimental study of tool wears to join Al6026 aluminium alloy by Ultrasonic Assisted Friction Stir welding

2021 ◽  
Author(s):  
Ivy Chowdhury ◽  
Kaushik Sengupta ◽  
Kaustav Kumar Maji ◽  
Swapna Roy ◽  
Sujit Ghosal
Keyword(s):  
Experimental Study ◽  
Friction Stir Welding ◽  
Aluminium Alloy ◽  
Friction Stir ◽  
Ultrasonic Assisted

scholarly journals Effect of Trailing Intensive Cooling on Residual Stress and Welding Distortion of Friction Stir Welded 2060 Al-Li Alloy

2018 ◽  
Vol 37 (5) ◽  
pp. 397-403 ◽  
Author(s):  
Shude Ji ◽  
Zhanpeng Yang ◽  
Quan Wen ◽  
Yumei Yue ◽  
Liguo Zhang
Keyword(s):  
Residual Stress ◽  
Friction Stir Welding ◽  
Plastic Strain ◽  
Welding Process ◽  
Butt Joint ◽  
Welding Distortion ◽  
Welding Temperature ◽  
Friction Stir ◽  
Numerical Simulation Methods ◽  
Conventional Cooling

AbstractTrailing intensive cooling with liquid nitrogen has successfully applied to friction stir welding of 2 mm thick 2060 Al-Li alloy. Welding temperature, plastic strain, residual stress and distortion of 2060 Al-Li alloy butt-joint are compared and discussed between conventional cooling and trailing intensive cooling using experimental and numerical simulation methods. The results reveal that trailing intensive cooling is beneficial to shrink high temperature area, reduce peak temperature and decrease plastic strain during friction stir welding process. In addition, the reduction degree of plastic strain outside weld is smaller than that inside weld. Welding distortion presents an anti-saddle shape. Compared with conventional cooling, the reductions of welding distortion and longitudinal residual stresses of welding joint under intense cooling reach 47.7 % and 23.8 %, respectively.

Process - Property Correlation of Friction Stir Welding of Marine Grade Aluminium Alloy 5083 Using Finite Element Analysis

2021 ◽  
Vol 163 (A2) ◽  
Author(s):  
M Sahu ◽  
A Paul ◽  
S Ganguly
Keyword(s):  
Mechanical Properties ◽  
Residual Stress ◽  
Finite Element ◽  
Friction Stir Welding ◽  
Residual Stresses ◽  
Process Variables ◽  
Friction Stir ◽  
Stress Region ◽  
Longitudinal Residual Stress ◽  
Process Property

In this article, a 3D finite element based thermo-mechanical model for friction stir welding (FSW) of a marine-grade aluminium alloy 5083 is proposed. The model demonstrates the thermal evaluation and the distribution of residual stresses and strains under the variation of process variables. The temperature profile of the weld joint during the FSW process and the mechanical properties of the joints are also experimentally evaluated. The necessary calibration of the model for the correct implementation of the thermal loading, mechanical loading, and boundary conditions was performed using the experimental results. The model simulation and experimental results are analyses in view of the process-property correlation study. The residual stress was evaluated along, and across the weld, centreline referred as longitudinal and transverse residual stresses, respectively. The magnitude of longitudinal residual stress is noted 60-80% higher than that of the transverse direction. The longitudinal residual stress generated a tensile oval shaped stress region around the tool shoulder confined to a maximum distance of about 25mm from the axis of the tool along the weld line. It encompasses the weld-nugget to thermo-mechanically affected zone (TMAZ), while the parent metal region is mostly experiences the compressive residual stresses. However, the transverse residual stress region appears like wing shaped region spread out in both the advancing and retreating side of the weld and occupying approximately double the area as compared to the longitudinal residual stresses. Overall, the study revealed a corelation between the FSW process variables such as welding speed and the tool rotational speed with the residual stress and the mechanical properties of the joint.

Sign in / Sign up

Export Citation Format

Share Document