The variable radial depth of cut in finishing machining of thin-walled blade based on the stable-state deformation field

2021 ◽  
Vol 113 (1-2) ◽  
pp. 141-158
Author(s):  
Yaohua Hou ◽  
Dinghua Zhang ◽  
Ying Zhang ◽  
Baohai Wu
Keyword(s):  
Stable State ◽  
Deformation Field ◽  
Depth Of Cut ◽  
Radial Depth ◽  
Thin Walled ◽  
Finishing Machining

scholarly journals OPTIMUM PERFORMANCE OF GREEN MACHINING ON THIN WALLED TI6AL4V USING RSM AND ANN IN TERMS OF CUTTING FORCE AND SURFACE ROUGHNESS

2019 ◽  
Vol 81 (6) ◽  
Author(s):  
Muhammad Yanis ◽  
Amrifan Saladin Mohruni ◽  
Safian Sharif ◽  
Irsyadi Yani
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Cutting Speed ◽  
Weight Ratio ◽  
Cutting Fluid ◽  
Depth Of Cut ◽  
Ann Model ◽  
Green Machining ◽  
Radial Depth ◽  
Thin Walled

Thin walled titanium alloys are mostly applied in the aerospace industry owing to their favorable characteristic such as high strength-to-weight ratio. Besides vibration, the friction at the cutting zone in milling of thin-walled Ti6Al4V will create inconsistencies in the cutting force and increase the surface roughness. Previous researchers reported the use of vegetable oils in machining metal as an effort towards green machining in reducing the undesirable cutting friction. Machining experiments were conducted under Minimum Quantity Lubrication (MQL) using coconut oil as cutting fluid, which has better oxidative stability than other vegetable oil. Uncoated carbide tools were used in this milling experiment. The influence of cutting speed, feed and depth of cut on cutting force and surface roughness were modeled using response surface methodology (RSM) and artificial neural network (ANN). Experimental machining results indicated that ANN model prediction was more accurate compared to the RSM model. The maximum cutting force and surface roughness values recorded are 14.89 N, and 0.161 µm under machining conditions of 125 m/min cutting speed, 0.04 mm/tooth feed, 0.25 mm radial depth of cut (DOC) and 5 mm axial DOC. 

Three-Dimensional Finite Element Simulation Analysis of Cutting Force of SiCp/Al Composite Thin-Walled Parts

2013 ◽  
Vol 589-590 ◽  
pp. 106-110 ◽  
Author(s):  
Yu Nan Liu ◽  
Shu Tao Huang ◽  
Li Zhou ◽  
Li Fu Xu
Keyword(s):  
Finite Element ◽  
Cutting Force ◽  
Simulation Analysis ◽  
Three Dimensional ◽  
Depth Of Cut ◽  
Milling Force ◽  
Machining Deformation ◽  
Al Composite ◽  
Radial Depth ◽  
Thin Walled

In milling process, cutting force is the main cause of machining deformation, and in machining of thin-walled parts, machining deformation is the major factor for machining error. In this paper, through finite element analysis software ABAQUS, three-dimensional simulation analysis on the machining of SiCp/Al composite thin-walled parts with a polycrystalline diamond tool have been carried out. It reveals the influence of radial depth of cut, cutting speed, and feed per tooth on cutting force. Analysis results show that: higher speed, small radial depth of cut and moderate feed per tooth can effectively reduce cutting force and inhibit deformation. In addition, a comparison is made between analysis results of milling force and high accuracy milling force prediction model, results from the two methods are similar.

scholarly journals High speed machining of the thin-walled aircraft constructions

Mechanik ◽  
2017 ◽  
Vol 90 (8-9) ◽  
pp. 726-729 ◽  
Author(s):  
Paweł Bałon ◽  
Edward Rejman ◽  
Robert Smusz ◽  
Bartłomiej Kiełbasa
Keyword(s):  
High Speed ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Internal Stresses ◽  
Depth Of Cut ◽  
Machining Errors ◽  
Radial Depth ◽  
Thin Walled ◽  
Machining Operations ◽  
Optimization Of Cutting Parameters

Machining operations of thin-walled elements generate a lot of production process issues related to deformations and elastic and plastic displacements of the workpiece. Due to displacements of the milled workpiece, vibrations can occur, and thus, geometric errors may occur on surface in the structure of the workpiece. Furthermore, plastic deformation can also cause shape problems and be a source of internal stresses in the surface layer, which are highly difficult to remove and lead to deformation of the workpiece after machining. Consequently, this leads to an increase in the manufacturing costs of machining operations, especially of thin-walled elements, due to shortages and increased manufacturing time. It is recommended that multiple methods for minimizing machining errors be utilized to improve the quality of thin walled elements, such as: optimization of the machining strategy, increase of the cutting speed vc, optimization of cutting parameters, especially feed per blade fz, the radial depth of cut ae due to the minimization of the cutting force component perpendicular to the surface of the milled wall.

Cutting Temperature and Cutting Forces Investigation Based on the Taguchi Design Method when High-Speed Milling of Titanium Matrix Composites with PCD Tool

2016 ◽  
Vol 836-837 ◽  
pp. 168-174 ◽  
Author(s):  
Ying Fei Ge ◽  
Hai Xiang Huan ◽  
Jiu Hua Xu
Keyword(s):  
Cutting Force ◽  
Feed Rate ◽  
Cutting Forces ◽  
High Speed ◽  
Volume Fraction ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
High Speed Milling ◽  
Radial Depth

High-speed milling tests were performed on vol. (5%-8%) TiCp/TC4 composite in the speed range of 50-250 m/min using PCD tools to nvestigate the cutting temperature and the cutting forces. The results showed that radial depth of cut and cutting speed were the two significant influences that affected the cutting forces based on the Taguchi prediction. Increasing radial depth of cut and feed rate will increase the cutting force while increasing cutting speed will decrease the cutting force. Cutting force increased less than 5% when the reinforcement volume fraction in the composites increased from 0% to 8%. Radial depth of cut was the only significant influence factor on the cutting temperature. Cutting temperature increased with the increasing radial depth of cut, feed rate or cutting speed. The cutting temperature for the titanium composites was 40-90 °C higher than that for the TC4 matrix. However, the cutting temperature decreased by 4% when the reinforcement's volume fraction increased from 5% to 8%.

Micro Flat End Milling Simulation Model With Instantaneous Plowing Area Prediction

2016 ◽  
Vol 4 (2) ◽  
Author(s):  
Abdolreza Bayesteh ◽  
Junghyuk Ko ◽  
Martin Byung-Guk Jun
Keyword(s):  
Feed Rate ◽  
Tool Path ◽  
End Milling ◽  
Chip Thickness ◽  
Depth Of Cut ◽  
Uncut Chip Thickness ◽  
Chip Area ◽  
Edge Radius ◽  
Wide Range ◽  
Radial Depth

There is an increasing demand for product miniaturization and parts with features as low as few microns. Micromilling is one of the promising methods to fabricate miniature parts in a wide range of sectors including biomedical, electronic, and aerospace. Due to the large edge radius relative to uncut chip thickness, plowing is a dominant cutting mechanism in micromilling for low feed rates and has adverse effects on the surface quality, and thus, for a given tool path, it is important to be able to predict the amount of plowing. This paper presents a new method to calculate plowing volume for a given tool path in micromilling. For an incremental feed rate movement of a micro end mill along a given tool path, the uncut chip thickness at a given feed rate is determined, and based on the minimum chip thickness value compared to the uncut chip thickness, the areas of plowing and shearing are calculated. The workpiece is represented by a dual-Dexel model, and the simulation properties are initialized with real cutting parameters. During real-time simulation, the plowed volume is calculated using the algorithm developed. The simulated chip area results are qualitatively compared with measured resultant forces for verification of the model and using the model, effects of cutting conditions such as feed rate, edge radius, and radial depth of cut on the amount of shearing and plowing are investigated.

A Comprehensive Study on Surface Roughness in Machining of AISI D2 Hardened Steel

2012 ◽  
Vol 576 ◽  
pp. 60-63 ◽  
Author(s):  
N.A.H. Jasni ◽  
Mohd Amri Lajis
Keyword(s):  
Surface Roughness ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Hardened Steel ◽  
Depth Of Cut ◽  
Feed Speed ◽  
Radial Depth ◽  
Aisi D2 ◽  
Coated Carbide

Hard milling of hardened steel has wide application in mould and die industries. However, milling induced surface finish has received little attention. An experimental investigation is conducted to comprehensively characterize the surface roughness of AISI D2 hardened steel (58-62 HRC) in end milling operation using TiAlN/AlCrN multilayer coated carbide. Surface roughness (Ra) was examined at different cutting speed (v) and radial depth of cut (dr) while the measurement was taken in feed speed, Vf and cutting speed, Vc directions. The experimental results show that the milled surface is anisotropic in nature. Surface roughness values in feed speed direction do not appear to correspond to any definite pattern in relation to cutting speed, while it increases with radial depth-of-cut within the range 0.13-0.24 µm. In cutting speed direction, surface roughness value decreases in the high speed range, while it increases in the high radial depth of cut. Radial depth of cut is the most influencing parameter in surface roughness followed by cutting speed.

SURFACE ROUGHNESS OF MAGNESIUM ALLOY AZ91D IN HIGH SPEED MILLING

2016 ◽  
Vol 78 (6-9) ◽  
Author(s):  
Mohd Shahfizal Ruslan ◽  
Kamal Othman ◽  
Jaharah A.Ghani ◽  
Mohd Shahir Kassim ◽  
Che Hassan Che Haron
Keyword(s):  
Surface Roughness ◽  
Magnesium Alloy ◽  
Feed Rate ◽  
High Speed ◽  
Cutting Parameters ◽  
Experimental Result ◽  
Depth Of Cut ◽  
Polishing Process ◽  
High Speed Cutting ◽  
Radial Depth

Magnesium alloy is a material with a high strength to weight ratio and is suitable for various applications such as in automotive, aerospace, electronics, industrial, biomedical and sports. Most end products require a mirror-like finish, therefore, this paper will present how a mirror-like finishing can be achieved using a high speed face milling that is equivalent to the manual polishing process. The high speed cutting regime for magnesium alloy was studied at the range of 900-1400 m/min, and the feed rate for finishing at 0.03-0.09 mm/tooth. The surface roughness found for this range of cutting parameters were between 0.061-0.133 µm, which is less than the 0.5µm that can be obtained by manual polishing. Furthermore, from the S/N ratio plots, the optimum cutting condition for the surface roughness can be achieved at a cutting speed of 1100 m/min, feed rate 0.03 mm/tooth, axial depth of cut of 0.20 mm and radial depth of cut of 10 mm. From the experimental result the lowest surface roughness of 0.061µm was obtained at 900 m/min with the same conditions for other cutting parameters. This study revealed that by milling AZ91D at a high speed cutting, it is possible to eliminate the polishing process to achieve a mirror-like finishing.

Tool Wear Characteristics in High Speed Milling of Ti-6Al-4V Alloy with Nitrogen Gas Medium

2006 ◽  
Vol 315-316 ◽  
pp. 588-592 ◽  
Author(s):  
Wei Zhao ◽  
Ning He ◽  
Liang Li ◽  
Z.L. Man
Keyword(s):  
Tool Wear ◽  
High Speed ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
High Speed Milling ◽  
Radial Depth ◽  
Oil Mist ◽  
Electron Microscopes ◽  
Scanning Electron Microscopes

High speed milling experiments using nitrogen-oil-mist as cutting medium were undertaken to investigate the characteristics of tool wear for Ti-6Al-4V Alloy, a kind of important and commonly used titanium alloy in the aerospace and automobile industries. Uncoated carbide tools have been applied in the experiments. The cutting speed was 300 m/min. The axial depth of cut and the radial depth of cut were kept constant at 5.0 mm and 1.0 mm, respectively. The feed per tooth was 0.1 mm/z. Optical and scanning electron microscopes have been utilized to determine the wear mechanisms of the cutting tools, and energy spectrum analysis has been carried out to measure the elements distribution at the worn areas. Meanwhile, comparisons were made to discuss the influence of different cutting media such as nitrogen-oil-mist and air-oil–mist upon the tool wear. The results of this investigation indicate that the tool life in nitrogen-oil-mist is significantly longer than that in air-oil-mist, and nitrogen-oil-mist is more suitable for high speed milling of Ti-6Al-4V alloy than air-oil-mist.

Cutting Forces and Surface Roughness in High-Speed End Milling of Ti6Al4V

2013 ◽  
Vol 589-590 ◽  
pp. 76-81
Author(s):  
Fu Zeng Wang ◽  
Jun Zhao ◽  
An Hai Li ◽  
Jia Bang Zhao
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Cutting Forces ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Wide Range ◽  
Radial Depth ◽  
Coated Carbide

In this paper, high speed milling experiments on Ti6Al4V were conducted with coated carbide inserts under a wide range of cutting conditions. The effects of cutting speed, feed rate and radial depth of cut on the cutting forces, chip morphologies as well as surface roughness were investigated. The results indicated that the cutting speed 200m/min could be considered as a critical value at which both relatively low cutting forces and good surface quality can be obtained at the same time. When the cutting speed exceeds 200m/min, the cutting forces increase rapidly and the surface quality degrades. There exist obvious correlations between cutting forces and surface roughness.

Sign in / Sign up

Export Citation Format

Share Document