Optimal calculation and experimental study on cutting force of hypoid gear processed by generating method

2021 ◽  
Author(s):  
Chuang Jiang ◽  
Jing Deng ◽  
Xiaozhong Deng
Keyword(s):  
Experimental Study ◽  
Cutting Force ◽  
Hypoid Gear ◽  
Generating Method ◽  
Optimal Calculation

Experimental Investigation of Microcutting Mechanisms in Marble Grinding

2009 ◽  
Vol 131 (6) ◽  
Author(s):  
LJ. Tanovic ◽  
P. Bojanic ◽  
R. Puzovic ◽  
S. Klimenko
Keyword(s):  
Experimental Study ◽  
Experimental Investigation ◽  
Cutting Force ◽  
Surface Finish ◽  
Normal Component ◽  
Natural Material ◽  
Grinding Process ◽  
Force Component ◽  
Diamond Grain

This paper offers an experimental study of the microcutting mechanisms in marble grinding to aid the optimization of the marble grinding process. The necessity for investigating these mechanisms is dictated by the increased use of marble in many applications and the fact that grinding and polishing processes are the dominant technologies used to meet surface finish requirements in this natural material. The experiments are aimed at the determination of the normal component of the cutting force and of the grain traces in microcutting with a single diamond grain. The investigations carried out make provisions for establishing critical grain penetration and cutting depths and allow the prediction of the normal cutting force component as a function of grain penetration speed and depth.

An Experimental Study of Cutting Force on Large Cutting Depth Turning Titanium Alloy with CBN Tool

2014 ◽  
Vol 800-801 ◽  
pp. 237-240
Author(s):  
Li Fu Xu ◽  
Ze Liang Wang ◽  
Shu Tao Huang ◽  
Bao Lin Dai
Keyword(s):  
Experimental Study ◽  
Titanium Alloy ◽  
Cutting Force ◽  
Feed Rate ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Cutting Depth ◽  
Cbn Tool ◽  
Cutting Experiment ◽  
Rough Turning

In this paper, the cutting experiment was used to study the influence of various cutting parameters on cutting force when rough turning titanium alloy (TC4) with the whole CBN tool. The results indicate that among the cutting speed, feed rate and cutting depth, the influence of the cutting depth is the most significant on cutting force; the next is the feed rate and the cutting speed is at least.

A Micromilling Experimental Study on AISI 4340 Steel

2009 ◽  
Vol 407-408 ◽  
pp. 335-338 ◽  
Author(s):  
Jin Sheng Wang ◽  
Da Jian Zhao ◽  
Ya Dong Gong
Keyword(s):  
Experimental Study ◽  
Surface Roughness ◽  
Cutting Force ◽  
Spectrum Analysis ◽  
Chip Thickness ◽  
Experimental Results ◽  
Minimum Chip Thickness ◽  
Aisi 4340 Steel ◽  
4340 Steel ◽  
Aisi 4340

A micromilling experimental study on AISI 4340 steel is conducted to understand the micromilling principle deeply. The experimental results, especially on the surface roughness and cutting force, are discussed in detail. It has been found the minimum chip thickness influences the surface roughness and cutting force greatly. Meanwhile, the material elastic recover induces the increase of the axial micromilling force. The average cutting force and its spectrum analysis validate the minimum chip thickness approximation of AISI 4340 is about 0.35μm.

Experimental Study on PCB Micro Drilling Force

2012 ◽  
Vol 246-247 ◽  
pp. 1017-1021 ◽  
Author(s):  
Feng Gong ◽  
Bai Qiang Chen ◽  
Ji Bin Li
Keyword(s):  
Experimental Study ◽  
Cutting Force ◽  
Printed Circuit Board ◽  
Circuit Board ◽  
Drilling Machine ◽  
Drilling Force ◽  
Printed Circuit ◽  
Market Competitiveness ◽  
Pcb Design ◽  
Micro Drilling

With the development of high density, multi-functions, miniaturization and multi-layer on printed circuit board (PCB) design, great challenges have been presented to the miniaturization of drilling on PCB. In order to meet the hole precision, quality and improve the performance, efficiency of mechanical drilling, further research should be done on the cutting state. Kistler high-precision micro-force platform was used in this paper to test and analyze the cutting force, investigate the general laws of micro drilling, and optimize the parameters for HANS PCB drilling machine. Thereby, to improve the efficiency and precision of the drilling, range of processing, and increasing market competitiveness.

scholarly journals Cutting force prediction in hypoid gear machining

2016 ◽  
Vol 10 (5) ◽  
pp. JAMDSM0082-JAMDSM0082
Author(s):  
Shinichi SHIRAISHI ◽  
Takashi KUSAKA ◽  
Takashi MATSUMURA
Keyword(s):  
Cutting Force ◽  
Hypoid Gear ◽  
Cutting Force Prediction ◽  
Force Prediction

Modeling Research of Hypoid Gear Based on Real Machining Process

2010 ◽  
Vol 20-23 ◽  
pp. 1429-1433
Author(s):  
Xiu Ting Wei ◽  
Jing Cheng Liu ◽  
Qiang Du
Keyword(s):  
Tooth Profile ◽  
Modeling Method ◽  
Machining Process ◽  
Transmission Ratio ◽  
Hypoid Gear ◽  
Hypoid Gears ◽  
Modeling Methods ◽  
Modeling Process ◽  
Generating Method

In this paper, two modeling methods, the forming method and the generating method, for hypoid gears with two kinds of transmission ratio are discussed by simulating the actual machining process. In the generating modeling method, the tooth profile of the gear is generated by boolean algorithm step by step after creating the models of the gear blank and the cutter and then rotating around their own axis by certain degrees until the cutter is outside the gear blank completely. In contrast with the generating modeling method, the tooth profile is formed by carrying out the boolean algorithm for one time after creating the models of the gear blank and cutter seperately in the forming modeling method. Then using feature instance, all the teeth are created both in the generating modeling method and in the forming modeling method. Using the two modeling methods given in this paper, the modeling process can be shortened and the modeling precision can be improved.

Sign in / Sign up

Export Citation Format

Share Document