Experimental study on cutting force and cutting temperature in high speed milling of hardened steel based on response surface method

2018 ◽  
Vol 13 (2) ◽  
pp. 99 ◽  
Author(s):  
Wei Zhang ◽  
Xiuqi Chen ◽  
Fengshun He ◽  
Tong Wu
Keyword(s):  
Experimental Study ◽  
Cutting Force ◽  
Response Surface ◽  
Response Surface Method ◽  
High Speed ◽  
Cutting Temperature ◽  
Hardened Steel ◽  
High Speed Milling ◽  
Surface Method

Cutting Temperature and Cutting Forces Investigation Based on the Taguchi Design Method when High-Speed Milling of Titanium Matrix Composites with PCD Tool

2016 ◽  
Vol 836-837 ◽  
pp. 168-174 ◽  
Author(s):  
Ying Fei Ge ◽  
Hai Xiang Huan ◽  
Jiu Hua Xu
Keyword(s):  
Cutting Force ◽  
Feed Rate ◽  
Cutting Forces ◽  
High Speed ◽  
Volume Fraction ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
High Speed Milling ◽  
Radial Depth

High-speed milling tests were performed on vol. (5%-8%) TiCp/TC4 composite in the speed range of 50-250 m/min using PCD tools to nvestigate the cutting temperature and the cutting forces. The results showed that radial depth of cut and cutting speed were the two significant influences that affected the cutting forces based on the Taguchi prediction. Increasing radial depth of cut and feed rate will increase the cutting force while increasing cutting speed will decrease the cutting force. Cutting force increased less than 5% when the reinforcement volume fraction in the composites increased from 0% to 8%. Radial depth of cut was the only significant influence factor on the cutting temperature. Cutting temperature increased with the increasing radial depth of cut, feed rate or cutting speed. The cutting temperature for the titanium composites was 40-90 °C higher than that for the TC4 matrix. However, the cutting temperature decreased by 4% when the reinforcement's volume fraction increased from 5% to 8%.

Vibration Signature Analysis of a Rotor Bearing System Using Response Surface Method

2009 ◽  
Author(s):  
P. K. Kankar ◽  
Satish C. Sharma ◽  
S. P. Harsha
Keyword(s):  
Response Surface ◽  
Response Surface Method ◽  
High Speed ◽  
Vibration Response ◽  
Radial Clearance ◽  
System Response ◽  
Surface Waviness ◽  
Surface Method ◽  
Rotor Bearing ◽  
Bearing System

The vibration response of a rotor bearing system is extremely important in industries and is challenged by their highly non-linear and complex properties. This paper focuses on performance prediction using response surface method (RSM), which is essential to the design of high performance rotor bearing system. Response surface method is utilized to analysis the effects of design and operating parameters on the vibration response of a rotor-bearing system. A test rig of high speed rotor supported on rolling bearings is used. Vibration response of the healthy ball bearing and ball bearings with various faults are obtained and analyzed. Distributed defects are considered as surface waviness of the bearing components. Effects of internal radial clearance and surface waviness of the bearing components and their interaction are analyzed using design of experiment (DOE) and RSM.

scholarly journals Cutting Performance Evaluation of the Coated Tools in High-Speed Milling of AISI 4340 Steel

Materials ◽  
2019 ◽  
Vol 12 (19) ◽  
pp. 3266 ◽  
Author(s):  
Yuan Li ◽  
Guangming Zheng ◽  
Xiang Cheng ◽  
Xianhai Yang ◽  
Rufeng Xu ◽  
...  
Keyword(s):  
Performance Evaluation ◽  
Cutting Force ◽  
High Speed ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Cutting Performance ◽  
High Speed Milling ◽  
Coated Tools ◽  
Coated Tool ◽  
Aisi 4340

The cutting performance of cutting tools in high-speed machining (HSM) is an important factor restricting the machined surface integrity of the workpiece. The HSM of AISI 4340 is carried out by using coated tools with TiN/TiCN/TiAlN multi-coating, TiAlN + TiN coating, TiCN + NbC coating, and AlTiN coating, respectively. The cutting performance evaluation of the coated tools is revealed by the chip morphology, cutting force, cutting temperature, and tool wear. The results show that the serration and shear slip of the chips become more clear with the cutting speed. The lower cutting force and cutting temperature are achieved by the TiN/TiCN/TiAlN multi-coated tool. The flank wear was the dominant wear form in the milling process of AISI 4340. The dominant wear mechanisms of the coated tools include the crater wear, coating chipping, adhesion, abrasion, and diffusion. In general, a TiN/TiCN/TiAlN multi-coated tool is the most suitable tool for high-speed milling of AISI 4340, due to the lower cutting force, the lower cutting temperature, and the high resistance of the element diffusion.

Optimization of Feed Speed and Stroke for Step Micro Hole Drilling of Printed Wiring Boards by Response Surface Method

2012 ◽  
Vol 523-524 ◽  
pp. 509-514 ◽  
Author(s):  
Naoya Noguchi ◽  
Toshiki Hirogaki ◽  
Eiichi Aoyama ◽  
Keiji Ogawa ◽  
Yutaka Takeda
Keyword(s):  
Response Surface ◽  
Response Surface Method ◽  
High Speed ◽  
Hole Drilling ◽  
Feed Speed ◽  
Printed Wiring Boards ◽  
Step Cycle ◽  
Stroke Length ◽  
Surface Method ◽  
Micro Drilling

There have been few reports dealing with the drilling of printed wiring boards (PWBs) with micro-drills that are smaller than 0.2 mm in diameter, and super-high-speed spindles that are higher than 160,000 rpm. In these cases, preventing the micro-drill from breaking and keeping the position accuracy of the drilled hole has been difficult. We therefore focus on the high-speed step-drilling method and short stroke as a novel way of resolving these problems. On the other hand, determining the complicated combination of feed speed, rapid feed speed, and stroke length is difficult. Under these backgrounds, in this report we propose a fast-feed step cycle that use fast-feed command without the processing feed. Thus, we attempted to apply the response surface method to optimize these parameters. As a result, a proposed method was found to be effective to improve the drilled hole quality and drilling efficiency in such kinds of micro-drilling of the PWBs.

Vibration response analysis of high-speed cylindrical roller bearings using response surface method

2020 ◽  
Vol 234 (2) ◽  
pp. 379-392
Author(s):  
Pravajyoti Patra ◽  
V Huzur Saran ◽  
SP Harsha
Keyword(s):  
Response Surface ◽  
Response Surface Method ◽  
High Speed ◽  
Dynamical Behavior ◽  
Roller Bearing ◽  
Interactive Effects ◽  
Response Analysis ◽  
Roller Bearings ◽  
Surface Method ◽  
Cylindrical Roller

The operating clearance in a bearing influences friction, load zone size and fatigue life of a bearing. Hence, an effort is made to investigate the effect of radial internal clearance on the dynamical behavior of a cylindrical roller bearing system with an unbalance present in the system. The differential equations representing the dynamics of the cylindrical roller bearings have been derived using Lagrange’s equations and solved numerically using the fourth-order Runge-Kutta iterative method. The nonlinear vibration signature has been analyzed due to the clearance and the same is represented by various tools like Acceleration-time plots, Poincaré plots and FFT plots. The approximation method is used to calculate the load distribution and deformation of the individual rollers located at a different position in the load zone, for a preloading/interference fit and positive internal clearance. A response surface method is used to analyze the severity involved in the system due to the combined effect of independent variables like rotor speed, radial load, and radial internal clearance. The observations presented here are not only useful to diagnose the bearing health condition with respect to parametric effects but also exhibit their interactive effects on bearing performance.

Sign in / Sign up

Export Citation Format

Share Document