Effects of process parameters on jet electrochemical machining of SiC particle-reinforced aluminum matrix composites

2021 ◽  
Vol 112 (11-12) ◽  
pp. 3351-3361
Author(s):  
Sansan Ao ◽  
Xiangyang Qin ◽  
Kangbai Li ◽  
Zhen Luo
Keyword(s):  
Process Parameters ◽  
Electrochemical Machining ◽  
Aluminum Matrix ◽  
Aluminum Matrix Composites ◽  
Matrix Composites ◽  
Jet Electrochemical Machining ◽  
Sic Particle

Drilling Characteristics of SiC Particle Reinforced Aluminum-Matrix Composites with Ultrasonic Vibration

2010 ◽  
Vol 455 ◽  
pp. 302-306 ◽  
Author(s):  
Xing Xin Xu ◽  
Xiao Hui Zhang ◽  
Chuan Shao Liu ◽  
Bo Zhao
Keyword(s):  
Surface Quality ◽  
Ultrasonic Vibration ◽  
Rapid Development ◽  
Aluminum Matrix ◽  
Aluminum Matrix Composites ◽  
Drilling Process ◽  
Matrix Composites ◽  
Drilling Force ◽  
Vibration Drilling ◽  
Sic Particle

With the rapid development of aviation at home, particle reinforced metal matrix composites (PRMMCs) has been widely applied recently. But at the same time, the difficult machining has gradually been one of the most outstanding bottle-necks that restrict the rapid enhancement of productivity. Here, in virtue of the self-developed ultrasonic drilling equipment, hole-making experiments of common and ultrasonic vibration drilling are performed on SiC particle reinforced aluminum-matrix composites （SiCp/Al）with different content of SiC by using two types of tungsten carbide drill. Drilling characteristics of machining composites with ultrasonic vibration are analyzed from such respects as the composites crush, drilling force, drill wear and hole surface quality. Studies show that, during the ultrasonic vibration drilling process, SiC particle in the composites is prone to break along the crystal connection boundary or suffer ductile fracture under the dynamic ultrasonic impulse, in which the cutting resistance could be reduced and the tool edge could be protected. Thereby, drilling locating precision and hole surface quality could be enhanced, wear of the drill chisel edge effectively improved, and the drilling torque reduced about 30%.

Microstructure and Properties of SiC Particle Reinforced Aluminum Matrix Composites by Powder Metallurgy Method

2013 ◽  
Vol 457-458 ◽  
pp. 131-134 ◽  
Author(s):  
Tao Fan ◽  
Cong Li Xiao ◽  
Yan Rong Sun ◽  
Hong Bo Li
Keyword(s):  
Particle Size ◽  
Wear Resistance ◽  
Powder Metallurgy ◽  
Sintering Temperature ◽  
Aluminum Matrix ◽  
Aluminum Matrix Composites ◽  
Average Particle ◽  
Particle Sizes ◽  
Matrix Composites ◽  
Sic Particle

The aim of this study is to investigate the effect of SiC particle pretreatment, aluminum matrix particle size and sintering temperature on relative density, hardness, microstructure and wear resistance to SiC particle einforced aluminum matrix composites. To this end, the amount of 16.7 wt.% SiC with average particle sizes 20μm was used along with pure aluminum of average particle size of 75 μm and 25μm. Powder metallurgy is a method used in the fabrication of this composite in which the powders were mixed using a planetary ball mill. By analyzing SEM micrograph and the Property test, it is concluded that SiC particle pretreatment has significant effect on the morphology of pecimens. pretreatment increase the interface adhesion, improve the wettability. SiC is uniformly distributed in the matrix, with good relation to the substrate, the maximum hardness is 51.1HB, the minimum wear rate is 0.1684%, while the density is 97.3%.For the same SiC content and particle size, the smaller the particle size of aluminum matrix is, the higher wear resistance of composite materials is on condition that others are same, the higher sintering temperature and the higher the wearability of composites, the wear resistance of the composite material is significantly improved after SiC pre-processing.The relative density increases with increasing aluminum matrix particle sizes under the same pressure and the holding time. The actual density of all samples reached the theoretical density over 96%, to a maximum of 98.9%.

Sign in / Sign up

Export Citation Format

Share Document