scholarly journals Orthogonal cutting of Wire and Arc Additive Manufactured parts

2022 ◽  
Author(s):  
Pedro P. Fonseca ◽  
Catarina Vidal ◽  
Francisco Ferreira ◽  
Valdemar R. Duarte ◽  
Tiago A. Rodrigues ◽  
...  
Keyword(s):  
Orthogonal Cutting

NUMERICAL AND EXPERIMENTAL MODELS FOR ORTHOGONAL CUTTING

2017 ◽  
Author(s):  
Fabio da Costa Figueiredo ◽  
Jose Luis Silveira ◽  
Nicole Dimas ◽  
Lavinia Maria Alves Borges
Keyword(s):  
Orthogonal Cutting ◽  
Experimental Models

Experimental and Numerical Investigation into Residual Stress During Turning Operation for Stainless Steel AISI 316

2020 ◽  
Vol 38 (12A) ◽  
pp. 1862-1870
Author(s):  
Safa M. Lafta ◽  
Maan A. Tawfiq
Keyword(s):  
Stainless Steel ◽  
Residual Stresses ◽  
Orthogonal Cutting ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Percentage Error ◽  
Depth Of Cut ◽  
Main Role ◽  
Turning Operation ◽  
Aisi 316

RS (residual stresses) represent the main role in the performance of structures and machined parts. The main objective of this paper is to investigate the effect of feed rate with constant cutting speed and depth of cut on residual stresses in orthogonal cutting, using Tungsten carbide cutting tools when machining AISI 316 in turning operation. AISI 316 stainless steel was selected in experiments since it is used in many important industries such as chemical, petrochemical industries, power generation, electrical engineering, food and beverage industry. Four feed rates were selected (0.228, 0.16, 0.08 and 0.065) mm/rev when cutting speed is constant 71 mm/min and depth of cutting 2 mm. The experimental results of residual stresses were (-15.75, 12.84, 64.9, 37.74) MPa and the numerical results of residual stresses were (-15, 12, 59, and 37) MPa. The best value of residual stresses is (-15.75 and -15) MPa when it is in a compressive way. The results showed that the percentage error between numerical by using (ABAQUS/ CAE ver. 2017) and experimental work measured by X-ray diffraction is range (2-15) %.

RESEARCH ON CUTTING FORCES AND CUTTING TEMPERATURE IN ORTHOGONAL CUTTING SOFTWOOD AND HARDWOOD PARALLEL TO GRAIN

2018 ◽  
Vol 50 (4) ◽  
pp. 458-464
Author(s):  
Xu Bao ◽  
Xiaolei Guo ◽  
Pingxiang Cao ◽  
Linlin Xie ◽  
Minsi Deng
Keyword(s):  
Cutting Forces ◽  
Orthogonal Cutting ◽  
Cutting Temperature

scholarly journals Serrated Chips Formation in Micro Orthogonal Cutting of Ti6Al4V Alloys with Equiaxial and Martensitic Microstructures

Micromachines ◽  
2019 ◽  
Vol 10 (3) ◽  
pp. 197 ◽  
Author(s):  
ZeJia Zhao ◽  
Suet To ◽  
ZhuoXuan Zhuang
Keyword(s):  
Cutting Force ◽  
Unit Length ◽  
Orthogonal Cutting ◽  
Machining Process ◽  
Orthogonal Machining ◽  
Large Yield ◽  
Power Spectral ◽  
Straight Line ◽  
Serrated Chips ◽  
Electropulsing Treatment

The formation of serrated chips is an important feature during machining of difficult-to-cut materials, such as titanium alloy, nickel based alloy, and some steels. In this study, Ti6Al4V alloys with equiaxial and acicular martensitic microstructures were adopted to analyze the effects of material structures on the formation of serrated chips in straight line micro orthogonal machining. The martensitic alloy was obtained using highly efficient electropulsing treatment (EPT) followed by water quenching. The results showed that serrated chips could be formed on both Ti6Al4V alloys, however the chip features varied with material microstructures. The number of chip segments per unit length of the alloy with martensite was more than that of the equiaxial alloy due to poor ductility. Besides, the average cutting and thrust forces were about 8.41 and 4.53 N, respectively, for the equiaxed Ti6Al4V alloys, which were consistently lower than those with a martensitic structure. The high cutting force of martensitic alloy is because of the large yield stress required to overcome plastic deformation, and this force is also significantly affected by the orientations of the martensite. Power spectral density (PSD) analyses indicated that the characteristic frequency of cutting force variation of the equiaxed alloy ranged from 100 to 200 Hz, while it ranged from 200 to 400 Hz for workpieces with martensites, which was supposedly due to the formation of serrated chips during the machining process.

scholarly journals Smoothed Particle Hydrodynamics Simulation of Orthogonal Cutting with Enhanced Thermal Modeling

2021 ◽  
Vol 11 (3) ◽  
pp. 1020
Author(s):  
Mohamadreza Afrasiabi ◽  
Hagen Klippel ◽  
Matthias Roethlin ◽  
Konrad Wegener
Keyword(s):  
Smoothed Particle Hydrodynamics ◽  
Metal Cutting ◽  
Thermal Modeling ◽  
Orthogonal Cutting ◽  
Detection Algorithm ◽  
Mesh Free ◽  
Particle Hydrodynamics ◽  
Smoothed Particle ◽  
Boundary Treatments ◽  
Cutting Problems

Smoothed Particle Hydrodynamics (SPH) is a mesh-free numerical method that can simulate metal cutting problems efficiently. The thermal modeling of such processes with SPH, nevertheless, is not straightforward. The difficulty is rooted in the computationally demanding procedures regarding convergence properties and boundary treatments, both known as SPH Grand Challenges. This paper, therefore, intends to rectify these issues in SPH cutting models by proposing two improvements: (1) Implementing a higher-order Laplacian formulation to solve the heat equation more accurately. (2) Introducing a more realistic thermal boundary condition using a robust surface detection algorithm. We employ the proposed framework to simulate an orthogonal cutting process and validate the numerical results against the available experimental measurements.

Sign in / Sign up

Export Citation Format

Share Document