Optimization of spray drying process parameters for production of Japanese apricot (Prunus mume Sieb. et Zucc.) juice powder

2021 ◽  
Author(s):  
Ju-Hui Kim ◽  
Jang H. Kim ◽  
Jong-Bang Eun
Keyword(s):  
Spray Drying ◽  
Process Parameters ◽  
Prunus Mume ◽  
Drying Process ◽  
Japanese Apricot

Effect of foam spray drying process parameters on powder morphology

2018 ◽  
Vol 37 (5) ◽  
pp. 535-545 ◽  
Author(s):  
Artur Lewandowski ◽  
Maciej Jaskulski ◽  
Ireneusz Zbiciński
Keyword(s):  
Spray Drying ◽  
Process Parameters ◽  
Drying Process ◽  
Powder Morphology

Impact of Spray-Drying Process Parameters on Dairy Powder Surface Composition and Properties

2015 ◽  
Vol 33 (13) ◽  
pp. 1654-1661 ◽  
Author(s):  
Y. Nikolova ◽  
J. Petit ◽  
A. Gianfrancesco ◽  
C. F. W. Sanders ◽  
J. Scher ◽  
...  
Keyword(s):  
Spray Drying ◽  
Process Parameters ◽  
Surface Composition ◽  
Drying Process ◽  
Powder Surface

scholarly journals Effect of spray drying process parameters on Uncaria tomentosa (Willd. ex Schult.) DC. dried extracts

Revista Fitos ◽  
2020 ◽  
Vol 14 (4) ◽  
pp. 469-475
Author(s):  
Lucas Oliveira Rodrigues ◽  
Rachel Andrade de Faria ◽  
Marcos Martins Gouvêa ◽  
Carlos Augusto de Freitas Peregrino ◽  
Elizabeth Valverde Macedo ◽  
...  
Keyword(s):  
Spray Drying ◽  
Process Parameters ◽  
Inlet Temperature ◽  
Airflow Rate ◽  
Spray Nozzle ◽  
Drying Process ◽  
Process Yield ◽  
Uncaria Tomentosa ◽  
Acacia Gum ◽  
Higher Temperature

Uncaria tomentosa (Willd. ex Schult.) DC. (Cat's claw) is a plant member of the Rubiaceae family, from the Amazon region, and used in traditional medicine as raw material for phytomedicines indicated for arthritis and osteoarthritis. This study aimed to evaluate the spray drying process parameters on the properties of different extracts obtained from Uncaria tomentosa. A reduced 24-1 multifactorial design was applied to evaluate the importance of the equipment variables (pump speed, spray nozzle diameter, air inlet temperature, and atomization airflow rate) in the process. Maltodextrin and acacia gum were used as carriers in a 1:1 (m/m) ratio, considering the solid residue content of the liquid plant extract. Process yield, moisture, and hygroscopicity were evaluated as dependent variables. Higher atomization airflow rate led to higher process yield for powdered dried extracts with maltodextrin. Higher temperature led to lower moisture contents regarding powdered dried extracts with acacia gum. No variable, for any carrier, was considered significant for hygroscopicity. The best spray drying configuration for the desired characteristics (i.e. lower hygroscopicity and moisture) used the larger spray nozzle with a diameter of 1.2 mm and the higher temperature of 150 °C, with both carriers.

Optimization of Spray Drying Process Parameters for Sweet Corn Enzymolysis Liquid

2015 ◽  
Vol 11 (3) ◽  
pp. 411-419 ◽  
Author(s):  
Ning Jiang ◽  
Chunquan Liu ◽  
Dajing Li
Keyword(s):  
Bulk Density ◽  
Spray Drying ◽  
Process Parameters ◽  
Feed Rate ◽  
Water Solubility ◽  
Sweet Corn ◽  
Production Yield ◽  
Inlet Temperature ◽  
Drying Process ◽  
Liquid Concentrate

Abstract The aim of this study was to optimize the spray drying process parameters for sweet corn enzymolysis liquid concentrate (SCELC). Experimental design with inlet temperature (170–190°C), SCELC/maltodextrin (MD) ratio (0.25–4) and inlet feed rate (800–1000 mL h−1) as independent variables was studied to investigate the effects on product responses. The corresponding results showed that an increase in the inlet temperature resulted in sweet corn powder with lower moisture, bulk density, L* value, H° value and higher water solubility index. Meanwhile, an increase in MD ratio brought lower moisture and higher L* value, H° value, water solubility index. It was also found that an increase in the inlet feed rate caused higher moisture and lower water solubility index. The highest production yield was achieved at 42.86% with optimized inlet temperature of 177.66°C, SCELC/MD ratio of 0.84 and inlet feed rate of 834.50 mL h−1. Accordingly, the production yield, moisture content, bulk density, water solubility index, L* and H° value were 42.86%, 3.57%, 0.45 g/cm3, 96.54 g/100 g, 84.46, and 83.54, respectively.

Sign in / Sign up

Export Citation Format

Share Document