Total Focusing Method Damage Imaging in Frequency Domain Using Laser-Ultrasonic Lamb Wave Based on Time-domain Filtering in Multi-band

Author(s):  
Fengzhong Li ◽  
Ying Luo
Author(s):  
Nitam Sunuwar ◽  
Jung-Ryul Lee

Interest in ultrasonic guided wave based Structural Health Monitoring and a nondestructive evaluation system has grown in recent years, especially to monitor thin plate like structures. However, an effective signal processing and imaging algorithms are essential to achieve necessary performance. This paper describes wave rich laser ultrasonic wavenumber imaging method (UWI) method for damage visualization. Ultrasonic waves were generated by a scanning laser source and acquired using a capacitance air coupled transducer (ACT). However, the inherent existence of multiple Lamb wave modes in signal makes it harder for effective damage evaluation. This is further complicated if the reflections from the boundaries are present in the signal. The use of an ACT with an in-line programmable filter helps to isolate lower order Lamb wave modes (Ao and So), since the dispersive waves radiate at certain angle from the specimen governed by Snell’s law. By comparing the results from the ultrasonic wavefield image obtained using the ACT and a PZT contact sensor under the same experimental condition, mode isolation phenomena was verified. Such isolated wave mode was processed using a proposed wave rich UWI algorithm where a wave rich field was generated by superposing the wavefields. The mode filtered measurements were arranged in 3D space-time domain where each slice in time domain represents 2D wavefield image. A 2D Fast Fourier Transform (FFT) was applied to this spatial information in time domain which transformed it to a wavenumber domain. A wavenumber filter is then applied and inverse Fourier transformed to get back to the wavenumber filtered measurement. However, instead of applying filter to every 2D slice in time domain, certain frames were selected and merged to replicate wave propagation in total scan-area. This wave rich field not only saves time and space but also reduce computational complexity during post-processing. This method was tested successfully in an aluminum plate with milled area damage and a composite fiber-reinforced plastic (CFRP) wing skin with two impact damages.


2018 ◽  
Vol 12 (7-8) ◽  
pp. 76-83
Author(s):  
E. V. KARSHAKOV ◽  
J. MOILANEN

Тhe advantage of combine processing of frequency domain and time domain data provided by the EQUATOR system is discussed. The heliborne complex has a towed transmitter, and, raised above it on the same cable a towed receiver. The excitation signal contains both pulsed and harmonic components. In fact, there are two independent transmitters operate in the system: one of them is a normal pulsed domain transmitter, with a half-sinusoidal pulse and a small "cut" on the falling edge, and the other one is a classical frequency domain transmitter at several specially selected frequencies. The received signal is first processed to a direct Fourier transform with high Q-factor detection at all significant frequencies. After that, in the spectral region, operations of converting the spectra of two sounding signals to a single spectrum of an ideal transmitter are performed. Than we do an inverse Fourier transform and return to the time domain. The detection of spectral components is done at a frequency band of several Hz, the receiver has the ability to perfectly suppress all sorts of extra-band noise. The detection bandwidth is several dozen times less the frequency interval between the harmonics, it turns out thatto achieve the same measurement quality of ground response without using out-of-band suppression you need several dozen times higher moment of airborne transmitting system. The data obtained from the model of a homogeneous half-space, a two-layered model, and a model of a horizontally layered medium is considered. A time-domain data makes it easier to detect a conductor in a relative insulator at greater depths. The data in the frequency domain gives more detailed information about subsurface. These conclusions are illustrated by the example of processing the survey data of the Republic of Rwanda in 2017. The simultaneous inversion of data in frequency domain and time domain can significantly improve the quality of interpretation.


2021 ◽  
Vol 9 (7) ◽  
pp. 781
Author(s):  
Shi He ◽  
Aijun Wang

The numerical procedures for dynamic analysis of mooring lines in the time domain and frequency domain were developed in this work. The lumped mass method was used to model the mooring lines. In the time domain dynamic analysis, the modified Euler method was used to solve the motion equation of mooring lines. The dynamic analyses of mooring lines under horizontal, vertical, and combined harmonic excitations were carried out. The cases of single-component and multicomponent mooring lines under these excitations were studied, respectively. The case considering the seabed contact was also included. The program was validated by comparing with the results from commercial software, Orcaflex. For the frequency domain dynamic analysis, an improved frame invariant stochastic linearization method was applied to the nonlinear hydrodynamic drag term. The cases of single-component and multicomponent mooring lines were studied. The comparison of results shows that frequency domain results agree well with nonlinear time domain results.


Sign in / Sign up

Export Citation Format

Share Document